1 / 21

Electrical principles

City and Guilds 2365 Certificate in Electro-technical Technology Level 3 Unit 1 Outcome 4 Session 1. Electrical principles. Outcome 4 Electrical principles. The aim of today is to understand the average and RMS values in an AC circuit. Objectives:

jane
Download Presentation

Electrical principles

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. City and Guilds 2365Certificate in Electro-technical TechnologyLevel 3 Unit 1 Outcome 4 Session 1 Electrical principles

  2. Outcome 4 Electrical principles The aim of today is to understand the average and RMS values in an AC circuit. Objectives: • To know how alternating current is produced • To understand what average and RMS values are, in relation to A.C and D.C supplies

  3. Alternating Current (a.c.) An alternating current (a.c) is produced when a coil is placed within a magnetic field and allowed to rotate. As the coil turns current is induced in the coil. The current in the coil varies depending on how much is being cut.

  4. Sinusoidal Wave The coil starts at a position where no magnetic flux is being cut. At this point if we were drawing a sinusoidal wave or sine wave this would be the 0 on the wave form diagram.

  5. Complete Sinusoidal Wave It moves from zero up to a maximum in one direction. It then moves from the maximum, back through zero Then on to a maximum in the opposite direction, Then to zero. Each complete wave is called a ‘cycle’ or ‘period’. The quantity of cycles in one second is called the ‘frequency’.

  6. Frequency The formula for frequency is; Frequency in the UK is 50Hz. Time is usually measured in seconds or milliseconds

  7. Labelling a sine wave The maximum or peak value cannot be the total useful current, power or voltage, as so much of the wave is less than the maximum. This is the average value. So to look at the average value of current or voltage we must only look at one of the half-cycles.

  8. Average Value of Current or Voltage In this instance, the average value is when a series of readings are taken at different points on the half-cycle and then averaged. Points at which readings would be taken. In the above example, the values are taken every 10 degrees. You could also take the values every 1 degree or even 30 degrees.

  9. Average Values The average value is found from this formula; Value (VAV) = V1 + V2 + V3 + V4 +…………Vn n It doesn’t matter what the size of the current or voltage is, the average value is always 0.637 times the maximum value available.

  10. Average formula Use the table to work out the average VAV = V1 + V2 + V3 + V4 + V5 + V6 6 373.2 divide by 6 = 62.2v. This is the average (Vav) of 100v max (Vmax)

  11. Average Values In D.C circuits, the powered delivered to a resistor is given by the product of voltage across the element and the current through the element. However, this is only true of instantaneous power to a resistor in an A.C circuit. An easy way to measure power is the RMS method.

  12. R.M.S What does RMS stand for? R.M.S stands for, root mean square. This is the effective value of a waveform. The ‘Root Mean Square’ of an alternating current is the value of equivalent direct current that would produce the same amount of heat in a fixed resistive load.

  13. Heating effect 100*C 70.7*C D.C A.C The heating effect of 1A max d.c across a resistor is100*C. But the heating effect of 1A max a.c is 70.7*C. Heating effect of 1A maximum a.c Heating effect of 1A maximum d.c = 0.7071

  14. R.M.S In the U.K, the single phase voltage is 230v. This is the RMS voltage. Multifunction meters (mft) measure RMS values.

  15. R.M.S values The RMS value is found using this formula; Mathematically the RMS voltage (VRMS) of a sinusoidal waveform is determined by multiplying the peak voltage(Vmax) value by 0.7071

  16. R.M.S table 0 2500 7499.56 10000 7499.56 2500 0 Using a table will help you simplify the RMS formula For this example the total squared figure is 29999.12

  17. R.M.S formula So now we have the squared total, the formula becomes a little easier to work out. 29999.12 = 70.71v VRMS = = 4999.85 6 Remember this value!

  18. When we say the main supply to a domestic property is 230V RMS, the maximum value would be 325.3V and the average value would be 207.2V.

  19. Remember In an A.C circuit the average value is 63.7% of the max value In an A.C circuit the RMS value is 70.71% of the max value

  20. Re-cap • AC voltage is produced when a coil rotates through a magnetic field. • Frequency is the number of cycles that occur every second • The maximum value of a waveform is Vpeak or Vmax • The average value of a waveform = 0.637 • The RMS value of a waveform = 0.7071 • Vrms= Vdc • All values of a.c voltage and current are given as RMS values

  21. Exercise Now have go at completing the exercise.

More Related