1 / 21

P11227- Active noise cancellation

P11227- Active noise cancellation. Kyle Desrosiers (ME)- Team Lead Brad Fiedler (EE) Greg Wodzicki (EE) Chris VanWagenen (EE) George Slack- Faculty Guide. Acknowledgements: Cenco Physics Texas Instruments. Project Description.

isaiah
Download Presentation

P11227- Active noise cancellation

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. P11227- Active noise cancellation Kyle Desrosiers (ME)- Team Lead Brad Fiedler (EE) Greg Wodzicki (EE) Chris VanWagenen (EE) George Slack- Faculty Guide Acknowledgements: Cenco Physics Texas Instruments

  2. Project Description • This project aims to attenuate sound level output of a given source using an Active Noise Cancellation system (ANC). • First of a series of projects ultimately targeting attenuation of Internal Combustion Engine.

  3. Key Customer Needs • Prove concept of sound attenuation via Active Cancellation • Demonstrate technical challenges limitations of ANC • ANC system fully functional to work on a given input

  4. Key Engineering specs • Noise reduction- Source only vs ANC system on • Target: >6dB • Ideal conditions: ~17dB • Effective Frequency range • Ideal: 20-20k Hz (Human Auditory Range) • Actual: 20-1000 Hz • Processing time • Ideal: 0.5 ms • Actual: Unknown • Speaker Output Level • ~100dB

  5. Concept summary • Sound Waves: • Propagation of compression and rarefaction through air Source: http://misclab.umeoce.maine.edu/boss/classes/SMS_491_2003/sound/sound_wave.jpg

  6. Super positioning of waves • Out of Phase • In Phase

  7. System Architecture • Microphones: Input Signal, Error Signal • Power Amplifier: Behringer EPQ1200 • Speaker: Goldwood GW-210/8 • DSP: • TAS3108EVM2 Eval Kit • C5505 DSP Eval Kit

  8. Design summary • System Spec’d for Lawn Mower Engine • Wye Configuration, Dipole Configuration • Speakers: • 10in, 110 Watt RMS • 86.5 dB Sound Level output • 40-2200 Hz • Amp • 2 x 320 Watts at 8 Ohms

  9. Design summary • Microphone • Typical Frequency Response • Cheap • For Initial Testing • DSP • TAS3108EVM2 Eval Kit • C5505 DSP EvalKit

  10. DSP • TAS3108EVM2 EvalKit • Sampling Rate: 192 kHz • Programmable in Assembly or GUI Interface • 8 Inputs/outputs • C5505 DSP Eval Kit • Sampling Rate: 48 kHz • Programmable in C++ • TI Support • 2 Inputs/Outputs

  11. Algorithm • Least Mean Squares (LMS) • Modeled in Matlab • Shown to Work • Unable to successfully implement in first DSP • Feedback issues using second DSP stalled implementation

  12. Testing/results • Matlab Simulation

  13. Testing/results • Test Setups Conducted • Straight Inverted Signal, Equal Path Length • Wye • Dipole Box

  14. Testing/results • 4in Pipe, Wye

  15. Testing/results • 4in Pipe, Dipole • Lawn Mower Sound Wave • 8dB Reduction

  16. Testing/results • 6in, Wye Connection • Complex Sounds • Dependent on sound • Achieved 8dB reduction

  17. Testing/Results • Using Microphones and DSP • Max Reduction achieved: 3dB • Feedback through mics limited test range • Testing conducted at low sound levels

  18. Successes and failures • Successes • Proof of concept • Geometry, superposition • Pure tones • Cancellation of low frequencies with inversion

  19. Successes and failures • Failures • Programming original DSP • Programming second DSP, fine tuning • Microphone Feedback, Clipping • Unable to implement on non electrical sound source

  20. Future work • Testing • 6 inch dipole setup • Back pressure with system in use • Algorithm debugged • New microphones • Eliminate feedback/clipping issue • System downsized, optimized • Application to mechanical sound source

  21. Suggestions • Computer engineer • Better knowledge of programming • Increased budget • Microphones with proper range, sensitivity, heat properties • More expert advice/input

More Related