1 / 11

Simultaneous Beam Training

Simultaneous Beam Training. Authors:. Date: March 2010. Background. Beamforming is necessary to achieve multi-Gbps throughput in 60 GHz band. Necessary to overcome severe path loss & directionality in 60 GHz. For a robust 60 GHz network:

hu-ball
Download Presentation

Simultaneous Beam Training

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Simultaneous Beam Training Authors: Date: March 2010

  2. Background • Beamforming is necessary to achieve multi-Gbps throughput in 60 GHz band. • Necessary to overcome severe path loss & directionality in 60 GHz. • For a robust 60 GHz network: • STAs needs to beam-train periodically to account for blockage, movement, change of orientation, etc. • STAs need to use dedicated service (time) periods to beam-train, to prevent traffic disruption to other 60 GHz devices. • The beam training overhead can be significant for 60 GHz network with multiple STAs.

  3. Example Beam-Training Overhead Calculation • Consider a conference Room scenario with 4 pairs of STAs communicating: • Assume beam training uses 15.3c long preamble (4.7μs) • Beam training by 4 pairs of STAs using separate dedicated times can lead to significant overhead. • This significantly reduces perceived network throughput

  4. Solution: Simultaneous Beam Training • Allow multiple pairs of STAs to perform beam training simultaneously • Each pair of STAs uses a different training sequence in order to mitigate interference • The different training sequences may be based on different Golay codes • It is easy to generate multiple Golay codes using the same hardware with good cross-correlation properties • Example: Two complementary Golay sequences of length 128 with good correlation properties • Simultaneous training of even 2 pairs of devices can reduce the beam training overhead by 50%

  5. Conference Room Simulation Setup • We will demonstrate performance of simultaneous Tx beam training of 2 pairs & 3 pairs of STAs • Channels generated using the TGad Conference Room channel model, and as defined in the TGad evaluation methodology • Transmitter parameters: • Training sequence is transmitted across each of Tx beams in a random order • 19 Tx beams total of 60o HPBW, covering the half-space z>0 • Receiver parameters: • Training sequence is received in an omni-directional mode (covering z>0) and using a simple correlator detector • Receiver selects the best Tx beam by comparing the strength of the received training sequences across all beam directions. • A random delay of 0-20 chips has been added to model in-room propagation delays. • Performance results are averaged over 100 channel realizations, and 10 noise realizations and beam-ordering per channel realization.

  6. Case #1: Simultaneous Training of 2 Pairs of STAs • Assume STA2STA1 training uses Golay code a128 from 802.15.3c • Assume STA7STA8 training uses Golay code b128 from 802.15.3c • To illustrate benefit of interference suppression using distinct Golay codes, performance is compared to the case where every STA uses a128 as the training sequence • 50% reduction of training overhead with no performance degradation

  7. Case #2: Simultaneous Training of 3 Pairs of STAs • Assume STA2STA1 and STA7 STA8 trainings use Golay codes a128 and b128 respectively, from 802.15.3c. • The third pair STA6STA3 training uses concatenation of Golay codes a64 and b64 from 802.15.3c Note: Failure events can be readily flagged as they correspond to low measured SINR of the selected beam. • 67% reduction of training overhead with minimal performance degradation.

  8. Enabling Simultaneous Beam Training in TGad • The Simultaneous Beam training concept can be overlayed on any beam training protocol: • Standard specifies a few Golay based training-sequences with good cross-correlation properties. • AP allocates the same service (time) period to more than one pair of STAs for beam training. • AP allocates distinct training sequences to these pairs of STAs • Alternately, STAs pseudo-randomly pick a distinct training sequence (e.g: based on STA-ID). • STAs can re-use existing HW to generate and detect these additional Golay based training-sequences. • Each STA needs to generate or detect only one Golay based training sequence, at any given time.

  9. Conclusion • Enabling simultaneous beam training of multiple pairs of STAs using different Golay-based training sequences can significantly reduce network overhead • Presented examples from the Conference Room Scenario where 3 pairs of STAs can simultaneously perform beam training, resulting in 67% training overhead reduction. • The additional Golay-based training sequences can be generated and detected without change to existing hardware • We are open to comments/suggestions to incorporate this concept in TGad.

  10. References [1] A. Maltsev et al., “Channel Models for 60 GHz WLAN Systems,” 802.11-09/0334r6, 01-20-2010. [2] E. Perahia, “TGad Evaluation Methodology,” 802.11-09/0296r16, 01-20-2010.

  11. Straw Poll • Do you support inclusion of the technique,    - Simultaneous Beam Training as described in 10/0252r0 in the TGad draft amendment? • Y: • N: • A:

More Related