1 / 45

Building Owners Roofing System Inspection and Maintenance

Building Owners Roofing System Inspection and Maintenance. Why Inspect and Maintain the Roofing System?. Periodic inspection and maintenance is needed in order for the roof to perform as designed .

greg
Download Presentation

Building Owners Roofing System Inspection and Maintenance

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Building Owners Roofing System Inspection and Maintenance

  2. Why Inspect and Maintain the Roofing System? • Periodic inspection and maintenance is needed in order for the roof to performasdesigned. • Inspection and maintenance is typically required by roofing manufacturers to keeproofingwarrantiesinfullforceandeffect.

  3. Proactive vsReactive Maintenance • ReactiveMaintenance:is a response to a existing problem: • Leaks • Repairs after damage due to weather events • Changes in the rooftop (relocated RTUs, new adjacent construction, etc.)

  4. Proactive vsReactive Maintenance • ProactiveMaintenance:stopping potential problems before they impact the roofing system - can create significant savings and extend the service life of the roofing system: The above cost analysis was prepared by a development firm owning in excess of 550 million square feet of commercial space.

  5. When Should the Roof Be Inspected? • Make a roof inspection plan part of the overall maintenance of the facility • Schedule regular inspections by on-site facility management team • Schedule twice-annual inspections by Roofing Professionals • Inspect following weather events (wind, hail, etc.) • Inspect when leaks or damage occurs

  6. Who Should Perform the Inspection? • The local facility staff can perform casual inspections: • Observe and record the status of the roofing system. • Use data gathered to direct a Roofing Professional to problem areas • A Roofing Professional should perform a thorough inspection: • At least twice a year. • Whenever repairs is required.

  7. Who Should Perform Maintenance? • Local facility management staff: • Clean single-ply membranes • Remove debris, especially from drains/scuppers/gutters • Locate areas of damage/leaks and safely mark them • Roofing Professionals: • Repair leaks and perform reactive maintenance • Perform proactive maintenance • Provide estimates for future roofing maintenance needs • Use manufacturer-licensed roofing contractors to protect your warranty

  8. Inspection ChecklistsWhere to Look - What to Look For - Remedial Actions • Rooftop Traffic Areas • Contaminants • Drainage Components • Wind Storm Damage • Moisture Infiltration • Roof Membrane Seams • Base Attachments

  9. Rooftop Traffic Areas • Where to Look: • Roof Hatch area or roof access points • Walkways and “natural” paths • Mechanical Equipment • What to Look For: • Cuts & punctures • Compressed/crushed insulation • Always monitor and log rooftop traffic Displaced walkway pads

  10. Rooftop Traffic Areas • Remediation: • Emergency repair of cuts and punctures • Duct tape open areas of single-ply membrane/flashing • Seal open asphalt membrane with plastic roof cement • Cover repaired area with tarp if possible • Permanent repair of cuts and punctures • Contact manufacturer’s licensed Roofing Professional • Crushed insulation • Have Roofing Professional replace with new insulation

  11. Rooftop Traffic Areas • Preventative Actions: • Add or enhance Roof Walkways • Register all rooftop traffic on a Roof Access Log Keep debris cleared! (…always remove ducks…!)

  12. Contaminants Membrane split Membrane swelling

  13. Contaminants • Where to Look: • Kitchen Exhaust Fans • HVAC Compressors Membrane swelling

  14. Contaminants • Remediation: • Membrane which has cracked, split, or swelled should be replaced by a Roofing Professional • Preventative Actions: • If grease traps are not present, consider installing grease traps • If sacrificial layer of membrane is not present, consider installing additional layer over waterproofing layer

  15. Drainage Components Roof Drain & Overflow Drain blocked by debris Open scupper flashings

  16. Drainage Components Debris in gutter, broken gutter straps, open fastener holes Blocked Drain

  17. Drainage Components • Where to Look: • Mid-span of Roof Beams & Joists • Around Rooftop Units (RTUs) • At Drains, Scupper, Gutters, Downspouts • What to Look For: • Debris • “Ponding,” Sagging, or Deflection • Discoloration at Curbs and Walls • Damage to Drainage Components

  18. Drainage Components • Remediation: • Remove Debris - bag and dispose • Drainage components – have Roofing Professional replace defective drainage components and flash them, according to manufacturer’s approved details. Blocked Drain

  19. Drainage Components • Preventative Actions: • Add roof drains • Add Tapered Insulation (“saddles and crickets”) • Add a redundant layer of membrane

  20. Wind Damage

  21. Wind Damage Displaced Insulation Boards “Tented” and Backed-Out Fasteners

  22. Wind Damage • Where to Look: • Roof Edge – metal, gutters, downspouts • Rooftop Units • Roof Membrane surface • Flashings – metal and membrane flashings Damaged Metal Coping

  23. Wind Damage What to Look For: • All Systems: • Loose or missing sheet metal flashing components, especially at the roof edge • Deflection or distortion of insulation boards • Large cuts or slices in the roof membrane • Ballastedsystems – displaced rock/pavers, displaced insulation boards under membrane • Adheredsystems – disbonded membrane, “tented” fasteners and plates • Mechanically Attachedsystems – “tented” fasteners

  24. Wind Damage Disbonded Membrane, Failed Base Attachments “Tented” Fasteners

  25. Wind Damage • Remediation: • Remove all debris • Replace any displaced ballast – carefully to avoid puncture • Seal small cuts and punctures • Have Roofing Professional resecure detached flashings and sheet metal • Have Roofing Professional make permanent repairs to membrane and reinstall/replace displaced/damaged insulation

  26. Wind Damage Damaged Metal Coping Displaced Ballast

  27. Wind Damage • Preventative Actions: • Add additional roof ballast to ballasted systems • Review roofing system design – have a Roof Consultant, engineer, or architect review the design and recommend changes to protect against future wind damage

  28. Moisture Infiltration • Where to Look: • Building Walls and Parapets • Large RTUs • Skylights Moisture infiltrating around RTU

  29. Moisture Infiltration • What to Look For: • “Soft” Roof Insulation • Cracking, Spalling, or Discoloration of Walls • Loose Metal Wall Flashings • Covered “Weep Holes” • Missing or Broken Weather Seals on RTU s • Cracked or Sunken Sealants/Caulking

  30. Moisture Infiltration • Remediation: • Replace wet roof insulation (should only be performed by a Roofing Professional) • Reattach and re-seal/caulk metal components (either by Roofing Professional or trade professional) • Repair deteriorated walls, parapets, substrates (should be performed by trade professional) Moisture stain on parapet wall

  31. Moisture Infiltration • Preventative Actions: • Have a Roof Consultant perform a Moisture Survey (Thermal Imaging, and/or core cuts) • Keep RTUs sealed to manufacturer’s standards • Log access to roof by RTU/HVAC maintainers Moisture Scan Image

  32. Roof Membrane Seams “Fishmouth” in seam • Where to Look: • T-Joints (membrane panel intersections) • Angle changes (such as deck-to-wall) • What to Look For: • Edge cavitation • Entrapped moisture

  33. Roof Membrane Seams • Remediation (Emergency Repairs): • Modified Bitumen (asphalt) Systems: • Apply plastic roof cement to the seam edge • Single-Ply Systems: • Gently clean the area, then cover the seam edge with duct tape extending 1.0” in all directions from seam opening • Remediation (Permanent Repairs) • Should only be made by Roofing Professionals Open Lap

  34. Base Attachments Failed Base Attachment Membrane “Bridging”

  35. Base Attachments • Where to Look: • Parapet Walls and Equipment Curbs • Roof Edge • What to Look For: • “Bridging” – membrane pulled away from the 90-degree angle change or greater than 2:12, forming an angled “bridge” from horizontal to vertical • Loose or “Tented” Fasteners

  36. Base Attachments Membrane Bridging • Remediation: • Emergency Repair: • If a leak is present, seal the area with duct tape (single-ply systems) or plastic roof cement (asphalt systems) • Permanent repair: • Base Tie-In and Membrane should be reattached and restored by a Roofing Professional

  37. Roofing Inspection Checklistfor use by on-site Facilities Managers • See Page 13 of the “Firestone Inspection, Repair, and Maintenance Guide” for a reproducible Roofing Inspection Checklist to carry to the rooftop. • Checklist contains a brief description of what to look for in all of the above conditions. • Note “Conditions Observed,” and “Actions Recommended” on the Checklist, along with the location of the problem area. • Reference completed Checklist when contact Roofing Manufacturer to report a leak or problem with the roofing system.

  38. Roofing Inspection Checklist

  39. Guide to Common Repair Methods • See the “Firestone Inspection, Maintenance, and Repair Guide,” Section II, for drawings and explanations of what quality repairs by a Roofing Professional should look like.

  40. Service Requests/Leak Reports • Firestone Warranty Services • 1-800-830-5612 - Line answered 24/7 • Fax information to 1-317-575-7210 • Email information to warrantyclaims@firestonebp.com

  41. Service Requests/Leak Reports • Provide the following information: • Building Name and Address • Building Owner Name • Name of contact on-site, fax number, and phone number • Warranty Number (printed on front of warranty) • Date when leak was observed • Description of leak or issue

  42. Fax Notification Form

  43. Warranted Repairs • Firestone issues a “Warranty Service Work Order” to the original installing contractor. • Building Owner or on-site contact is faxed an acknowledgement letter with roofing contractor’s contact information • Contractor will investigate and complete necessary repairs within 10 working days

  44. Non-Warranted Repairs • Roofing System Warranties typically cover repair of leaks • Most other conditions are non-warranted • Building Owner is responsible for payment of investigation and repair of non-warranted conditions

  45. Questions?

More Related