1 / 11

Ch 14: Phase Equilibria

Ch 14: Phase Equilibria. I. Condensed Phase ↔ Vapor II. TR: Eqns Vi. and Vj. III. More Cycles IV. Surface Tension. I. Condensed Ph. ↔ Vapor. At constant T and p, the Extremum Principle states that equilibrium is associated with Δ G = 0  μ c = μ v Recall Example 7.5

graceland
Download Presentation

Ch 14: Phase Equilibria

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Ch 14: Phase Equilibria I. Condensed Phase ↔ Vapor II. TR: Eqns Vi. and Vj. III. More Cycles IV. Surface Tension

  2. I. Condensed Ph. ↔ Vapor • At constant T and p, the Extremum Principle states that equilibrium is associated with ΔG = 0 • μc = μv Recall Example 7.5 • If gas is ideal, μv = kT ℓn (p/pint0) Eqn 11.50

  3. Use Lattice Model for Condensed Phase • Treat liquids and solids the same (ie ignore long range forces in solids) • ΔStrans = 0 (condensed phase atoms held “in place”) • ΔF = ΔU = f(trans only) • Let attractive interaction energy = wAA which is negative and independent of T.

  4. Use Lattice Model for Condensed Phase • Assume N atoms each with z nearest neighbors (n.n.), ΔF = ΔU = Nz wAA/2 Eqn 14.6 • μc = (∂F/∂N)T,V = z wAA/2 Eqn 10.41 • μc = μv p = pint0exp (z wAA/2kT) • Creating cavities or holes in a cond. ph. (ΔUremove), closing the hole (ΔUclose) and opening the hole(ΔUopen = - ΔUclose).

  5. II. Phase Equilibrium Eqns (TR) • Clapeyron Eqn: general phase equil eqn • At constant T and p, dG = -TdS + V dp is the indicator for equilibrium. • Since μ = partial molar G, μ can be used. • dμ = -sdT + vdp • Consider liquid ↔ vapor or μℓ = μv • dp/dT = Δs/Δv = Δh/T Δv Eqn Vi (TR) • Applies to s ↔ ℓ; v ↔ ℓ; s ↔ v, s1 ↔ s2, etc

  6. Clausius-Clapeyron Eqn • Applies to s ↔ g and ℓ ↔ g. • Assume ideal gas, Δv = vg, Δh ≠ f(p,T) • Then Clapeyron Eqn becomes CC Eqn • d ℓn p = Δh/RT2 dT • ℓn (p2/p1) = [- Δh/R][1/T2 – 1/T1] Eqn 14.23

  7. Clausius-Clapeyron Eqn • ℓn (p2/p1) = [- Δh/R][1/T2 – 1/T1] Eqn 14.23 • Measure p vs T to find Δh/R = -slope or Δh for sublimation and vaporization. Fig 14.8, Table 14.1 • Δhvap = - z wAA/2 Eqn 14.24 • Prob 3, 7, 8

  8. III. Refrigerators and Heat Pumps • Working fluid operates in a cycle • Take heat from cold reservoir (qc at Tc, refrigerator or outside) and dumps it into high temperature (qh at Th, room or house) sink. • Note cycle in Fig 14.9 showing H vs p • Determine coefficient of performance c = gain/work

  9. IV. Surface Tension (γ) • Surface = interface between two phases (e.g. liquid and vapor). • Surface tension = free energy cost to increase surface area = γ • Consider lattice model again with N molecules total including n on surface with (z-1) n.n. and (N-n) in bulk with z n.n. • Total surface area = A = na

  10. Surface Tension (γ) • U = [wAA/2] [Nz-n] Eqn 14.25 • γ = (∂F/∂A)T,V,N = (∂U/∂N)T,V,N = - [wAA/2a] • γ increases as wAA increases (becomes more negative) • γ increases as a decreases (molecular area decreases) • γ has units of dyn/cm = force/length = erg/cm2 Table 14.2

  11. Surface Tension (γ) • U = [wAA/2] [Nz-n] Eqn 14.25 • γ = (∂F/∂A)T,V,N = (∂U/∂N)T,V,N = - [wAA/2a] • Eqn 14.24 + 14.28  γ = Δhvap /za Fig 14.12 • Prob 2,4

More Related