1 / 24

DAQ System to Search for GRBs using Water Cerenkov Detectors

DAQ System to Search for GRBs using Water Cerenkov Detectors. Mario Castillo*, Gonzalo Perez*, Humberto Salazar* and L. Villaseñor ** * Facultad de Ciencias FisicoMatematicas, BUAP, Puebla  ** Institute of Physics and Mathematics, University of Michoacan, Morelia. VII SILAFAE CAB

geordi
Download Presentation

DAQ System to Search for GRBs using Water Cerenkov Detectors

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. DAQ System to Search for GRBs using Water Cerenkov Detectors Mario Castillo*, Gonzalo Perez*, Humberto Salazar* and L. Villaseñor ** * Facultad de Ciencias FisicoMatematicas, BUAP, Puebla  ** Institute of Physics and Mathematics, University of Michoacan, Morelia VII SILAFAE CAB Bariloche, Ar January, 13-21, 2009

  2. WCD array at Sierra Negra to search for GRBs

  3. 4550 masl (610 g/cm2)‏

  4. 4m2 x 1.4 m Single 5” EMI flat PMT Tyvek Ultra pure (~20 microS)‏ water

  5. Schematic of the DAQ Board (one channel upgradable to 3 channels)‏ Languages: VHDL + Perl & AWK 50 Mhz Clock JTAG PROM FPGA Xilinx Spartan 2E Antenna RS232 115200 Baud 4 operation modes: Trace, Charge, Rate, Muon Decay 1 PPS VP or UT Oncore GPS Receiver 50 ns 2x-4x clock Serial 9600 Baud RAM 10 bit ADC board 100-200 MHz|| Signal from PMT

  6. ADC daugther boards 1 or 2 AD9214BRSZ-105 chips operating at 100MSPS.

  7. We use one (two) delay-locked loop (DLL) circuits to obtain 100 (200) Mhz out of 50 MHz

  8. Use a Motorola Oncore GPS receiver in precise Timing Mode model UT+ Position-Hold option 1PPS Cable and antenna Delay Time RAIM option to isolate satellites with erroneous time measurements

  9. Trace mode, samples 30 trace points every 10 ns in real time and measures charge, amplitude, baseline and STD

  10. Trace Mode: Up to 180 full traces per second Bottle- neck: 115200 baud comm rate

  11. Charge mode: Up to 2880 Charge & Amplitude measurements per second (1920 per s if rise time is also measured)‏

  12. Measure Charge, Amplitude,T10-50,T10-90 with good precision for three different triggers. Arbitrary muons threshold of 30mV

  13. 1.54 m diameter, 1.2 m water, one 8” PMT, tyvek 1/5 in volume of an Auger WCD

  14. LabView based DAS

  15. Rise time behaves similarly to Charge over amplitude

  16. Charge spectrum 2000 masl 4550 masl

  17. Muon decay mode: Time between consecutive pulses in a 20 microsec window and time over threshold with granularity of 5 ns

  18. Stopping muon at 0.1 VEM Decay electron at 0.17 VEM Crossing muon at 1.05 VEM Alarcón M. et al., NIM A 420 [1-2], 39-47 (1999).

  19. Rate mode: Number of pulses above 4 thresholds every 5 ms

  20. Conclusions DAQ system prototype tested 1-3 ADC channels at 100-200 MHz Precise timing from GPS 4 operation modes: Trace, charge, muon decay and rate To do: implement as a single board

More Related