1 / 50

Mechanical Properties and Their Measurement

Mechanical Properties and Their Measurement. Metallurgy for the Non-Metallurgist. Learning Objectives. Upon completion of this lesson, you can: Outline the procedures for performing tensile and hardness tests List the three categories of properties measured by the tensile test

gaston
Download Presentation

Mechanical Properties and Their Measurement

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Mechanical Properties and Their Measurement Metallurgy for the Non-Metallurgist

  2. Learning Objectives • Upon completion of this lesson, you can: • Outline the procedures for performing tensile and hardness tests • List the three categories of properties measured by the tensile test • Describe a fatigue test in general terms • Define yield and ultimate strengths, elongation in two inches., impact toughness, creep rate, and fatigue endurance limits

  3. Tensile Test • Load Limits • Stress • s = F/A = force/cross-sectional area

  4. Tensile sample showing grip and gage sections

  5. Illustration of stress as the ratio of force to cross-sectional area

  6. Stress Stress, σ = F/A = force in Newtons(poundss) area in m2(in.2) Newton/meter2 = Pascal We use megaPascals, MPa, and KSI 15 KSI = ~103 MPa

  7. Strain Strain, ε = Δ L / L0 Strain is dimensionless, may be elastic or plastic

  8. Stress-Strain Curves • Stress at which a metal or alloy deforms must be established • This is the goal of the tensile test stress-strain curve • Force and stress are converted to stress and strain • Properties measured include • Yield strength • Modulus of elasticity (Young’s modulus • Ultimate strength • Elongation to fracture

  9. Typical conventional stress-strain curve for a copper tensile sample

  10. Early strain region of tensile stress-strain curve for copper

  11. E is a measure of the stiffness of a material

  12. Variation in modulus of elasticity of iron, copper, and aluminum. Note that iron has the highest stiffness while aluminum has the lowest stiffness of the three metals.

  13. Relationships between stiffness and melting temperatures

  14. Percent Elongation to Fracture

  15. Typical stress-strain curve of a low-carbon steel showing a yield point

  16. New and failed tensile bars showing region of necking and reduction in cross-sectional area

  17. Reduction in Area

  18. Tensile stress-strain curve for metal, used to illustrate uniform elongation and necking strain

  19. Hardness Testing

  20. Relationship between hardness and tensile strength of steel

  21. Brinell hardness tester

  22. Size specifications for hardness indenters

  23. (a) Induction-hardened gear cross section. (b) Etched cross section of a carburized gear. (c) Etched cross section of a nitrided gear. Images courtesy of Caterpillar, Inc.

  24. Micrograph illustrating the size of a Knoop microhardness indentation relative to the size of microstructural constituents in a D4 tool steel. Original magnification, 1000×

  25. Impact Test

  26. Schematic illustration of the effect of temperature on the tensile behavior of low-carbon steel. (The elastic portion of the stress-strain curves is actually nearly vertical but is sketched to illustrate that temperature decreases the modulus of elasticity as well as the yield strength.)

  27. Impact TesterTests the abilityto arrest cracks

  28. Schematic of an impact test

  29. Impact test machine

  30. Typical shape of a Charpy and Izod impact sample

  31. Lack of penetration and undercut in a fillet weld

  32. Effect of temperature on the impact toughness of a low-carbon steel

  33. Effect of nickel content on the ductile-to-brittle transition of (a) low-carbon steels and (b) medium-carbon steels

  34. Scanning electron micrographs of fracture surfaces of samples that failed in ductile and brittle fashions: (a) Typical dimpled-rupture fracture surface of a ductile fracture viewed at an original magnification of 2000× (shown at 75%) and at an angle of approximately 40–50° to the fracture surface. (b) Intergranular fracture in hardened steel. Note that fracture takes place between the grains; thus, the fracture surface has a “rock candy” appearance that reveals the shapes of part of the individual grains. Original magnification 2000×, shown at 75%

  35. Effect of grain size on ductile-to-brittle transition temperature and yield strength of low-carbon steel

  36. Creep Testing

  37. Illustration of a creep curve

  38. (a) Ruptured superheater tubes. Original magnification, 0.2×. (b) Creep cracks found in metallographic section of 1.25Cr-0.25Mo steel steam pipe. Original magnification, 160×; nital etch. (c) Creep cavities that are linking to form cracks visible in (b). Original magnification, 1500×; nital etch

  39. Fatigue Test

  40. (a) Reversed bending fatigue of a 40 mm (1.6 in.) diameter shaft of 1046 steel with a hardness of approximately 30 HRC. Note the symmetrical fatigue pattern of beach marks on each side, with the final rupture on the diameter. This indicates that each side of the shaft was subjected to the same maximum stress and to the same number of load applications. The C-shaped marks are postfracture damage. (b) Fatigue striations showing the result of spectrum loading in a laboratory test of aluminum alloy 7075-T6. In this test, the specimen was loaded ten cycles at a high stress, then ten at a lower stress, and alternated with these stresses as the fatigue crack continued to propagate. This produced ten large striations, then ten small striations, alternately, across the fracture surface. Original magnification, 4900×

  41. A stress vs. number of cycles to failure, or S-N, curve for a fatigue test of a steel

  42. ASTM Grain Size Grid to be viewed at 100×

  43. Major causes of fatigue failure • Design! Keyways! • Must use chamfers, avoid stress raisers • Corrosion can create stress risers

  44. Grain Size Small grains favorable for strength and fatigue resistance Large grains favorable at high temperatures ASTM Grain Size Number, N: Number of grains/in2 at 100X = 2N-1 Now generally given in microns

  45. Grain size and strength,Hall-Petch relationship Strength fine coarse 1/ (grain size)1/2

  46. Summary • Major mechanical tests: tensile, hardness, impact, creep, and fatigue • Behavior relatable to crystal structure, grain size, alloy, and dislocation response to stress • Described by ASTM standards

More Related