1 / 41

Chapter 30

Chapter 30. Operational Amplifiers. Introduction. Characteristics High input impedance Low output impedance High open-loop gain Two inputs One output Usually + and – dc power supplies. Introduction. Ideal Characteristics z in (inverting) ≈ ∞ z in (non-inverting) ≈ ∞ z out ≈ 0

Download Presentation

Chapter 30

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Chapter 30 Operational Amplifiers

  2. Introduction • Characteristics • High input impedance • Low output impedance • High open-loop gain • Two inputs • One output • Usually + and – dc power supplies

  3. Introduction • Ideal Characteristics • zin (inverting)≈ ∞ • zin (non-inverting)≈ ∞ • zout≈ 0 • Av≈ ∞ V+ Inverting Input - Output + Non-Inverting Input V-

  4. Introduction • Uses • Comparators • Voltage amplifiers • Oscillators • Active filters • Instrumentation amplifiers V+ Inverting Input - Output + Non-Inverting Input V-

  5. Introduction • Single-ended amplifier • One input grounded • Signal at other input • Double-ended amplifier/Differential amplifier • Signals at both inputs V+ Inverting Input - Output + Non-Inverting Input V-

  6. Differential Amplifier and Common-Mode Signals • Basic differential amplifier • Q1 identical to Q2 • RC1 = RC2 • IC1 = IC2 and emitter currents equal • Also, IC≈ IE for high β • and VBE ≈ 0.7 V • Similar calculation of Bias

  7. VCC IC2 IC1 RC1 RC2 Q1 Q2 __ _ - __ _ - IE RE ◦ –VEE Differential Amplifier and Common-Mode Signals

  8. VCC IC2 IC1 RC1 RC2 Q1 Q2 __ _ - __ _ - IE RE ◦ –VEE Differential Amplifier and Common-Mode Signals • Apply same signal to both Bases Vout = Vout1 – Vout2≈ 0 • Eliminates common-mode signals • 60 Hz • Noise

  9. VCC IC2 IC1 RC1 RC2 Q1 Q2 __ _ - __ _ - IE RE ◦ –VEE Differential Amplifier and Common-Mode Signals • Apply sinusoids to both bases: • Same amplitude, 180° difference in phase, if Vin1 = –Vin2 Vout = 2Vin

  10. Differential Amplifier and Common-Mode Signals • Common-mode signals • Differential voltage gain also called open-loop voltage gain 20,000≤Av≤200,000

  11. Differential Amplifier and Common-Mode Signals • Common-mode signals • Common-mode voltage gain

  12. Differential Amplifier and Common-Mode Signals • Common-mode rejection ratio (CMRR) • Equations • Values

  13. Differential Amplifier and Common-Mode Signals • Noise • Static in audio signal • Increases as signal is amplified • Common mode signal • Significantly reduced by differential amplifier vnoise - vin + __ _ - __ _ -

  14. Negative Feedback • Op-amp • Large differential, open-loop voltage gain • Avol≈ 100,000 • Small input yields saturated output (VCC or VEE)

  15. Negative Feedback • Negative feedback • Returns a portion of output signal to the input • Open-loop voltage gain decreased

  16. Negative Feedback • Input impedance still high • Output impedance low • Circuit voltage gain, Av • Adjustable • Stable Negative Feedback - + vout vin __ _ -

  17. Inverting Amplifier • Basic circuit

  18. Inverting Amplifier • Output 180° out of phase with input • Significant decrease in gain • Gain now called closed-loop voltage gain • Output impedance ≈ 0 • vd ≈ 0

  19. Inverting Amplifier • Inverting input at virtual ground, vin(-)≈ 0 • iin to op-amp ≈ 0 • Input current only dependent on vinand R1 • Avclonly dependent on input resistor and feedback resistor

  20. Inverting Amplifier • Model • vd≈ 0 • Rin ≈ ∞ • iin = if • zin ≈ R1 RF R1 i = 0 if + - + iin vin vd Rin - + - Rout vout(OC) - + __ _ - Avolvd internal __ _ -

  21. Inverting Amplifier • Low output impedance RF R1 i = 0 if + - + iin vin vd Rin - i1 Rout iout(sc) - + __ _ - __ _ - Avolvd internal __ _ -

  22. Non-Inverting Amplifier • Circuit

  23. The Non-Inverting Amplifier • Very high input impedance • Voltage gain related to the two resistors • Very low output impedance • Excellent buffer

  24. Non-Inverting Amplifier • Differential voltage • vd≈ 0 • Input current to op-amp • i = 0 • Closed-loop voltage gain (Avcl) is a resistor ratio

  25. Non-Inverting Amplifier

  26. Non-Inverting Amplifier • Model • Input impedance vin + iin vd Rin zin vout - Rout - + + - Avolvd internal R1 __ _ - - + __ _ - RF if

  27. Non-Inverting Amplifier • Model • Output impedance i2 + iin vd Rin - Rout - + + - Avolvd internal R1 __ _ - - + __ _ - __ _ - RF if iout(sc)

  28. Non-Inverting Amplifier • Very high zin • Very low zout • Good buffer circuit • Also called voltage follower (gain = 1) • Or adjustable gain > 1

  29. Non-Inverting Amplifier • Voltage Follower Buffer Circuit • Gain = 1 • High impedance source drives low impedance load

  30. Op-Amp Specifications • LM 741 series • Inexpensive • Widely used • Good general specifications • Characteristic of all op-amp specifications • Provide Minimum, Typical, and Maximum ratings

  31. Op-Amp Specifications • Input Offset Voltage, Vio • LM741C, Vio typical is 2 millivolts • Model is voltage source with value, Vio in series with + input

  32. Op-Amp Specifications • Input Offset Voltage, Vio • Without feedback this would saturate output with no input • With negative feedback, output due to Vio is closed-loop gain times Vio

  33. Op-Amp Specifications • Input Offset Current, Ios • Ios= Difference between bias currents at + and – inputs of op-amp • 741C typical Ios is 20 nanoamps • Multiplying resistor used to measure Ios

  34. Op-Amp Specifications • Input Resistance • 741C: minimum = .3 MΩ, typical = 2 MΩ • Open-Loop Voltage gain (Avol) • 741C: Avol = Large Signal Voltage Gain • minimum = 20,000, typical = 200,000 • Closely related to Bandwidth, BW

  35. Op-Amp Specifications • Gain-bandwidth product • 741C = 1,000,000 = 106 MHz

  36. Op-Amp Specifications • Gain versus frequency curve for op-amp

  37. Op-Amp Specifications • Slew rate • Maximum rate of change of output voltage • 741C maximum slew rate = 0.5 V/μsec

  38. Op-Amp Specifications • Fastest time for output to go from 0 to 10 volts is 20 μsec • Can distort waveforms that have too fast a rise time

  39. Op-Amp Specifications • Slew rate required for Sinusoid with frequency f and amplitude A • Maximum amplitude of a sine wave with frequency f for a given slew rate

  40. Op-Amp Specifications • Bias Compensation: use RC = R1||RF

  41. Troubleshooting an Op-Amp Circuit • Problems occur when circuit is first built • Most important • Correct connection of dual power supply • Connecting a – supply to a + input (or vice versa) can burn out an op-amp • Single earth ground • Short connecting wires

More Related