1 / 28

Chapter 26A - Capacitance

Chapter 26A - Capacitance. A PowerPoint Presentation by Paul E. Tippens, Professor of Physics Southern Polytechnic State University. © 2007. Objectives: After completing this module, you should be able to:.

ember
Download Presentation

Chapter 26A - Capacitance

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Chapter 26A - Capacitance A PowerPoint Presentation by Paul E. Tippens, Professor of Physics Southern Polytechnic State University © 2007

  2. Objectives: After completing this module, you should be able to: • Define capacitance in terms of charge and voltage, and calculate the capacitance for a parallel plate capacitor given separation and area of the plates. • Define dielectric constant and apply to calculations of voltage, electric field intensity, and capacitance. • Find the potential energy stored in capacitors.

  3. Conductor Battery - - - - - - Earth - - - e- e- - - - - - Maximum Charge on a Conductor A battery establishes a difference of potential that can pump electrons e-from a ground (earth) to a conductor There is a limit to the amount of charge that a conductor can hold without leaking to the air. There is a certain capacity for holding charge.

  4. Conductor Battery - - - - - - Earth - - - e- e- - - - - - Capacitance The capacitance C of a conductor is defined as the ratio of the charge Q on the conductor to the potential V produced. Q, V Capacitance:

  5. Capacitance in Farads One farad (F) is the capacitance C of a conductor that holds one coulomb of charge for each volt of potential. Example:When 40 mC of charge are placed on a con- ductor, the potential is 8 V. What is the capacitance? C = 5mF

  6. r +Q E and V at surface. Capacitance of Spherical Conductor At surface of sphere: Capacitance, C Recall: Capacitance: And:

  7. Capacitance, C r +Q r = 0.08 m Example 1:What is the capacitance of a metal sphere of radius 8 cm? Capacitance: C = 4peor C = 8.90 x 10-12 F Note: The capacitance depends only on physical para- meters (the radius r) and is not determined by either charge or potential. This is true for all capacitors.

  8. Capacitance, C r +Q r = 0.08 m Example 1 (Cont.):What charge Q is needed to give a potential of 400 V? C = 8.90 x 10-12 F Q = 3.56 nC Total Charge on Conductor: Note: The farad (F) and the coulomb (C) are extremely large units for static electricity. The SI prefixes microm, nano n, and pico p are often used.

  9. r Q Dielectric Dielectric Strength The dielectric strength of a material is that electric intensity Em for which the material becomes a conductor. (Charge leakage.) Em varies considerably with physical and environmental conditions such as pressure, humidity, and surfaces. For air: Em = 3 x 106 N/C for spherical surfaces and as low as 0.8 x 106 N/C for sharp points.

  10. Maximum Q r Air Q Em = 3 x 106 N/C Example 2:What is the maximum charge that can be placed on a spherical surface one meter in diameter? (R = 0.50 m) Qm = 83.3mC Maximum charge in air: This illustrates the large size of the coulomb as a unit of charge in electrostatic applications.

  11. + + + + + + + + + + + + + + + + + + + + + + + + + + + + + Capacitance and Shapes The charge density on a surface is significantly affected by the curvature. The density of charge is greatest where the curvature is greatest. Leakage (called corona discharge) often occurs at sharp points where curvature r is greatest.

  12. For these two parallel plates: Area A +Q d -Q Parallel Plate Capacitance You will recall from Gauss’ law that E is also: Qis charge on either plate. Ais area of plate. And

  13. A 0.4 m2 d 3 mm Example 3.The plates of a parallel plate capacitor have an area of 0.4 m2 and are 3 mm apart in air. What is the capacitance? C = 1.18 nF

  14. Changing Area + + + + + - + - + - A - - Changing d - - Variable Capacitor d Microphone Applications of Capacitors A microphone converts sound waves into an electrical signal (varying voltage) by changing d. The tuner in a radio is a variable capacitor. The changing area A alters capacitance until desired signal is obtained.

  15. reduced E E < Eo Eo - - - + + + - + - + - + - - - + + + - - + - + + Air - + - + - + - - - + + + - + - + - + - - + + - + - - + - + + Co C > Co Dielectric Dielectric Materials Most capacitors have a dielectric material between their plates to provide greater dielectric strength and less probability for electrical discharge. The separation of dielectric charge allows more charge to be placed on the plates—greater capacitance C > Co.

  16. Advantages of Dielectrics • Smaller plate separation without contact. • Increases capacitance of a capacitor. • Higher voltages can be used without breakdown. • Often it allows for greater mechanical strength.

  17. Field decreases. +Q +Q E < Eo Voltage decreases. Co Vo Eo eo + + + + -Q -Q + V < Vo + Insertion of a dielectric Capacitance increases. C > Co C V E e + + Same Q Permittivity increases. Q = Qo e > eo Insertion of Dielectric Air Dielectric

  18. Dielectric Constant, K The dielectric constant K for a material is the ratio of the capacitance C with this material as compared with the capacitance Co in a vacuum. Dielectric constant: K = 1 for Air K can also be given in terms of voltage V, electric field intensity E, or permittivity e:

  19. The Permittivity of a Medium The capacitance of a parallel plate capacitor with a dielectric can be found from: The constant eis the permittivity of the medium which relates to the density of field lines.

  20. e = Ke0 A 0.5 m2 d 2 mm Example 4: Find the capacitance Cand the charge Q if connected to 200-V battery. Assume the dielectric constant is K = 5.0. e = Ke0= 5(8.85 x 10-12C/Nm2) eo = 44.25 x 10-12 C/Nm2 C = 11.1 nF Q if connected to V = 200 V? Q = 2.22 mC Q = CV = (11.1 nF)(200 V)

  21. e = Ke0 A 0.5 m2 200 V d 2 mm Example 4 (Cont.): Find the field E between the plates. Recall Q = 2.22 mC; V = 200 V. e = 44.25 x 10-12 C/Nm2 E = 100 N/C Since V = 200 V, the same result is found if E = V/d is used to find the field.

  22. Air dielectric Vo = 400 V Mica dielectric Mica, K = 5 Example 5:A capacitor has a capacitance of 6mF with air as the dielectric. A battery charges the capacitor to 400 V and is then disconnected. What is the new voltage if a sheet of mica (K = 5) is inserted? What is new capacitance C ? V = 80.0 V C = Kco = 5(6 mF) C = 30mF

  23. Air Co = 6 mF Vo = 400 V Mica C = 30 mF Mica, K = 5 Example 5 (Cont.):If the 400-V battery is reconnected after insertion of the mica, what additional charge will be added to the plates due to the increased C? Q0 = C0V0 = (6 mF)(400 V) Q0 = 2400 mC Q = CV = (30 mF)(400 V) Q = 12,000 mC DQ = 12,000 mC – 2400 mC DQ = 9600 mC DQ = 9.60mC

  24. Energy of Charged Capacitor The potential energyU of a charged capacitor is equal to the work (qV) required to charge the capacitor. If we consider the average potential difference from 0 to Vf to be V/2: Work = Q(V/2) = ½QV

  25. Capacitor of Example 5. C = 11.1 nF 200 V U = ? Q = 2.22 mC Example 6: In Ex-4, we found capacitance to be 11.1 nF, the voltage 200 V, and the charge 2.22 mC. Find the potential energy U. U = 222 mJ Verify your answer from the other formulas for P.E.

  26. Energy Density u for an E-field: A d Energy Density u: Energy Density for Capacitor Energy density u is the energy per unit volume (J/m3). For a capacitor of area A and separation d, the energy density u is found as follows:

  27. Summary of Formulas

  28. CONCLUSION: Chapter 25Capacitance

More Related