1 / 27

4-20mA Basics and 2-Wire vs. 3-Wire Transmitters

4-20mA Basics and 2-Wire vs. 3-Wire Transmitters. Material Created by Scott Hill Presented by Ian Williams May 23, 2011. Background. Prior to the 1950s, control of industrial sites was achieved with pneumatic systems 3 psi – 15 psi was used as the standard signal span 3 psi  0%

chaela
Download Presentation

4-20mA Basics and 2-Wire vs. 3-Wire Transmitters

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. 4-20mA Basics and 2-Wire vs. 3-Wire Transmitters Material Created by Scott Hill Presented by Ian Williams May 23, 2011

  2. Background • Prior to the 1950s, control of industrial sites was achieved with pneumatic systems • 3 psi – 15 psi was used as the standard signal span • 3 psi  0% • 15 psi  100% • 3 psi used as a “live zero” • < 3 psi considered a fault condition or “dead zero” • The 4-20mA current loop was developed to emulate the old 3-15 psi pneumatic system

  3. Typical 4-20mA Applications Report a process variable from a remote sensor to a control station. • Temperature, pressure, flow • 2-wire transmitter Transmit control signals from a control station out to a remote device. • Valve, actuator, heater • 3-wire transmitter

  4. 4-20mA Overview • 4mA represents 0% input level • Allows up to 4mA to power external input circuitry • 4mA zero level allows under-scale settings and fault detection • 20mA represents 100% input level • Provides sufficient current to power electromechanical devices • Over-scale can also be used to detect fault conditions

  5. Why Use Current Transmitters? • Immunity to noise • Multiple unknown noise sources can exist between transmitter and receiver • Low impedance system prevents noise from impacting the accurate regulation of loop current • Long distance transmission • Signals must often travel distances > 1 mile • Impedance of long wires would severely attenuate a voltage signal • 4-20mA current loops are lossless, even over long distances • Kirchoff’s Current Law states that the current in a loop is equal at any point within the loop

  6. Current Transmitter Function

  7. Why Is Signal Conditioning Required? • Linearity errors on most sensors creates an unacceptable error.

  8. Transmitter Type Diagrams 2-Wire Transmitter 3-Wire Transmitter

  9. 2-Wire vs. 3-Wire Transmitter • Application-specific parameters determine which transmitter type should be used • Accessibility and location • System power requirements • Sensor input or voltage/current input

  10. 2-Wire vs. 3-Wire Transmitter • 2-Wire Transmitter (Loop powered) • Transmitter and sensor remotely located • Local power supply not practical • Input circuitry floats with respect to loop supply ground • 3-Wire Transmitter (Locally powered) • Transmitter located close to power supply • Input is referenced to power supply ground • Also known as a voltage-to-current converter

  11. Common 2-Wire Transmitter Applications

  12. Implementation Of Current Transmitters • 2-Wire Transmitter • Submersible temperature sensor • Remote location prevents local power supply • Sends data back to control station • 3-Wire Transmitter • Sends control signal to element at remote location • Local power supply is available

  13. 2-Wire Transmitters

  14. 2-Wire Typical Input Scaling • 4-20mA span is 16mA • XTR117 has current gain of 100 • Input span is 160µA • Offset current needed if input signal reaches zero

  15. 2-Wire Typical Input Interface

  16. Typical 2-Wire Transmitter • IRET is not GND • Current Input • Current Output • Current gain set by R1 and R2 • Regulator and input circuitry floats at IRET potential

  17. 2-Wire Transmitter Common Abuse

  18. Grounded Loop Supply with Floating Input Source

  19. Internal Current Paths IINTotal = IIN + IOffset IR1 = IIN Total IR2 = IR1 * 99 ILOOP = IR1 + IR2

  20. Equal Path Voltages Created VR1 = VR2

  21. Calculating IRET Level VFLOAT = ILOOP * RL VFLOAT = ILOOP * RL VR2 = R2 * IR2 VR2 = R2 * IR2 V IRET = VFLOAT + VR2 V IRET = VFLOAT + VR2 V IRET = 5.495V V IRET = 1.099V

  22. Effects of Grounding IRET IRET Floating IRET Grounded

  23. 3-Wire Transmitters

  24. Typical 3-Wire Transmitter • Input and Output are referenced to GND • Voltage Input • Current Output • Current gain set by VIN and RSET • Regulator referenced to GND

  25. XTR111 Typical Input Interface

  26. 4-20mA Product Family

  27. Thank You!

More Related