html5-img
1 / 22

Markov Analysis

Markov Analysis. Jørn Vatn NTNU. Introduction. Markov analysis is used to model systems which have many different states These states range from “perfect function” to a total fault state The migration between the different states may often be described by a so-called Markov-model

bruno-lott
Download Presentation

Markov Analysis

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Markov Analysis Jørn Vatn NTNU

  2. Introduction • Markov analysis is used to model systems which have many different states • These states range from “perfect function” to a total fault state • The migration between the different states may often be described by a so-called Markov-model • The possible transitions between the states may further be described by a Markov diagram

  3. Purpose • Markov analysis is well suited for deciding reliability characteristics of a system • Especially the method is well suited for small systems with complicated maintenance strategies • In a Markov analysis the following topics will be of interest • Estimating the average time the system is in each state. These numbers might further form a basis for economic considerations. • Estimating how frequent the system in average “visits” the various states. This information might further be used to estimate the need for spare parts, and maintenance personnel. • Estimate the mean time until the system enters one specific state, for example a critical state.

  4. Markov Analysis procedure • Make a sketch of the system • Define the system states • Draw the Markov diagram with the transition rates • Quantitative assessment • Compilation and presentation of the result from the analysis

  5. Make a sketch of the system • Pump system wit active pump and a spare pump in standby

  6. Definition of system states • x1 = state of active pump • x2 = state of standby pump

  7. State transitions • For this system we have assumed that if the active pump fails, the standby pump could always be started • Further we assume that if both pumps have failed, they will both be repaired before the system is put into service again • The following transition rates are defined 1 = failure rate of the active pump 2 = failure rate of the standby pump (while running, 2 = 0 in standby position) 1 = repair rate of the active pump (1/1 = Mean Down Time when the active pump has failed) B = repair rate when both pumps are in a fault state. I.e. we assume that if the active pump has failed, and a repair with repair rate 1 is started, one will ”start over again” with repair rate B, if the standby pump also fails, independent of “how much” have been repaired on the active pump.

  8. Markov state space diagram • The circles represent the system states, and the arrows represent the transition rates between the different system states • The Markov diagram and the description of states represent the total qualitative description of the system

  9. Quantitative assessment • We want to assess the following quantities • Average time the system remain in the various system states • The visiting frequencies to each system state

  10. Transition matrix • The indexing starts on 0, and moves to r, e.g. there are r +1 system states • Each cell in the matrix has two indexes,where the first (row index) represent the ”from” state, whereas the second (column index) represent the “to” state. • The cells represent transition rates from one state to another • aijis thus the transition rate from state i to state j • The diagonal elements are a kind of ”dummy”-elements, which are filled in at the end, and shall fulfil the condition that all cells in a row adds up to zero

  11. Example transition matrix: (From , To )

  12. State probabilities • Let Pi(t) represent the probability that the system is in state i at time t • Now introduce vector notation, i.e. • P(t) = [P0(t), P1(t),…,Pr(t)] • From the definition of the matrix diagram it might be shown that the Markov state equations are given by:P(t)A = dP(t)/dt • These equations may be used to establish both the steady state probabilities, and the time dependent solution

  13. Steady state probabilities • Let the vector P = [P0, P1,…,Pr] represent the average time the system is in the various system states in the long time run • For example, P0 is average fraction of the time the system is in state 0, P1 is average fraction of the time the system is in state 1 • The elements P = [P0, P1,…,Pr] are also denoted steady state probabilities to indicate that in the stationary situation Pi represents the probability that the system is in state i.

  14. The steady state solution • In the long run when the system has stabilized we must have that dP(t)/dt = 0, hence • PA = 0 • This system of equations is over-determined, hence we may delete one column, and replace it with the fact thatP0+ P1+…+Pr = 1 • Hence, we have

  15. The steady state solution PA1 = b where and b = [0,0, …,0,1]

  16. Example which gives

  17. Numerical solution • To solve the steady state equations PA1 = b is a tedious task • Often we therefore solve these equations by numerical methods • The Markov.xls program does this, where we have to: • Define the transition rates • Assign numerical values to the transition rates • Specify the Markov state space matrix

  18. Visiting frequencies • Often we are interested in evaluating how many times the system enters the various states, i.e. the visiting frequencies • The visiting frequency for state j is denoted j, and could be obtained by: • j = -Pjajj • From our example we obtain the “system failure rate”

  19. Time dependent solution • Up to now we have investigated the steady state situation • In some situations we also want to investigate the time dependent solution, i.e. the probability that the system is in e.g. state 0 at time t • We now let Pi(t) be the probability that the system is in state i at time t • The time dependent solution may be found by: • P(t)A = dP(t)/dt • Which could be solved by Laplace methods, or numerical methods • For numerical methods we apply Markov.xls

  20. Spare parts – Simple model • Assume a spare part regime where there is only one spare in the stock • Upon a demand (with demand rate ) a new spare is ordered • The intensity of arrival of a new spare is  = 1/ MTA (Mean Time to Arrival)

  21. Spare parts 2 spares in stock • Assume a spare part regime wheretherearetwo spares in thestock • Upon a demand (withdemand rate ) a new spare is ordered • The intensityofarrivalof a new spares is  = 1/ MTA (Mean Time to Arrival) independentofhowmany in order

More Related