1 / 57

Advanced Digital Circuits ECET 146 Week 3

Advanced Digital Circuits ECET 146 Week 3. Professor Iskandar Hack ET 221B, 481-5733 hack@ipfw.edu. This Week’s Goals. Designing a Combinational Circuit from Truth Table Introduction to the Programming Hardware Verifying a design in Hardware. Designing from a Truth Table.

ayla
Download Presentation

Advanced Digital Circuits ECET 146 Week 3

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Advanced Digital CircuitsECET 146Week 3 Professor Iskandar Hack ET 221B, 481-5733 hack@ipfw.edu

  2. This Week’s Goals • Designing a Combinational Circuit from Truth Table • Introduction to the Programming Hardware • Verifying a design in Hardware

  3. Designing from a Truth Table • Write a Sum of Product Equation straight from the truth table • Draw the schematic from the Equation • No Need to minimize equation (the software will find the minimum solution for the Altera architecture)

  4. Writing the Equation • Look at the Truth Table and everywhere the output is a one then you will generate a term in the Sum of Products • The term generated will depend on the values of ABCD in the table for that term. • If the value for an input is a zero then the term would contain an T-not • If the value for an input is an one then the term would contain T

  5. Table Equivalent Terms • The Term for each of the entries is shown here

  6. Example 1 • Write the Equation for the following table

  7. Comments regarding Example 1 • There were 8 – ones in the table, thus there would be 8 terms in the equation • Each one will create exactly one term, that can be easily written by looking at the table and writing the term by looking at the values • Example if you look at the third line of the table A = 0, B=0, C=1, and D=0 and the output is 1. That would generate the term

  8. Solution to Example 1

  9. Drawing Schematic • Open Altera Quartus II Software • File->New->Schematic File • Insert Inputs and inverters to create inputs for AND gates • Draw AND gates, selecting appropriate inputs for each • OR the output of the eight AND gates • Insert Output

  10. Insert Inputs and Inverters Draw the following circuit using INPUT and Inverters and draw the wires out of each inverter as shown

  11. Name Pins and Nets • As in previous labs name the pins A-D • Click on each wire from the inputs and name them A-D • Click on each wire from the inputs and name them Anot-Dnot

  12. Add AND4 Gates • Insert 8 – AND4 gates (remember one AND gate per term)

  13. Connect Inputs to AND Gates • Connect the four inputs to the AND gates according to the equation. • This is done by drawing a small wire from each input and naming it as before. • Name them according to the equations from the previous slide

  14. The AND gates Connected

  15. Add OR8 and connect the Product Terms

  16. Insert Output (and name it)

  17. Completed Schematic

  18. Save File Click this to Create project

  19. Creating the Project -1 First two screens take default and hit next

  20. Device Number Part Number (EP3C16F484C6N)

  21. Creating the Project – II (Select Device) Cyclone II Family Need a specific device EP2C20F484C7 is the chip on the board Hit OK when done

  22. Compiling the Project • Hit the hot key on the top of the screen to start compiling your project.

  23. The Compiler • If you did everything right thus far you should see something like this:

  24. Compiler Reports The compiler creates a number of reports, which at this point would mean nothing to you, but you may want to explore them. Boolean EQ I/O pin info

  25. Comments regarding errors • It is very possible that you’ll get errors on this drawing. If so look for two connections on a wire to one of the AND gate inputs. This is the most common error. This often happens on the last AND gate if the wires brought down end at the same point you draw the wire across. Just delete the wire and redraw it.

  26. Assigning Pins - I • Open the Pin Planner to Assign the pins

  27. Assigning Pins II • Look at the data sheet for the board and determine what your pin numbers need to be.

  28. Assigning Pins III • Use four of the switches for the inputs • Use one of the LEDs for the output

  29. Assigning the Pins IV

  30. Tristate Unused Pins Device and Pin Options

  31. Tristate Unused Pins II

  32. Recompile after Assigning Pins and tristating unused pins

  33. Check New Pin Assignments • Open the resource files to look at the pin assignment after recompiling. Output pins Click to look at input pins Input pin assignments

  34. NOTE: • The following slides were copied from Lecture two and the waveforms DO NOT match this example. They are included for instructional purposes only.

  35. Drawing Waveforms for Simulation • We now need to create a new file to hold our simulation input waveforms. This done by hitting new and selecting Other and vector waveform file (vwf)

  36. Entering Nodes You will need to double click in the node area of the display – this will bring up the following dialog box Select Node Finder

  37. Entering Nodes II (1) Start by selecting Pins: all (2) Then hit List (3) Move all pins to the right by hitting >> (4) Hit OK

  38. Check if all nodes are selected • Verify in the waveform editor that all nodes are shown Inputs Output

  39. Change Grid and End Time • Select Edit, Grid time, and change it to 50 nS • Select Edit, End time and change it to 1.6 uS

  40. Grouping Inputs • Select all the inputs, right click, hit ‘Group’ and use inputs[3..0] for the name of the inputs, Hex as radix, and uncheck grey count

  41. Display after Grouping + will expand group to show the individual pins - will hide individual pins

  42. Using Count Function • Select the Group, and then hit the count button on the left side of the screen. Take the defaults (start at 0, incr by 1, End value F)

  43. Display after Count • You should see the following after hitting OK

  44. Save Simulation File • Up to now you should have seen that the output is neither high or low. That is because it has not been simulated yet. • In order to simulate you must first save the file as example1.vwf Leave checked

  45. Simulate • This is the easy part – Hit the simulate button on the top of the screen. Simulate

  46. Verify Simulation • You should have a value for the output for each input condition. • Manually determine (using techniques from ECET 111) what the output should be for each condition and verify that the output matches that.

  47. Simulation Display

  48. Connect the Altera Board to the PC • Check out an Altera Board from the Lab Tech office

  49. Connect Board to PC I • When checking out board also check out DC wall pack. Ensure that the wall pack is of the correct polarity (+ is the center, - is the outside) and is between 9 and 12 volts. • Also get a Male -> Female DB25 cable to connect between the computer and the PC

  50. Connect to PC II • Notice the location of the connectors used, the other DB25 connector is used for experiments. DC Power connector DB25 Cable to PC

More Related