1 / 28

TIW CORPORATION A PEARCE INDUSTRIES COMPANY

TIW CORPORATION A PEARCE INDUSTRIES COMPANY. P.O. Box 35729 Houston, Texas 77235-5729 U. S. A. TIW Abrasive Jet Drilling System (JETDRILL). Abrasive Jet Casing Cutter (JCUTTER) Abrasive Jet Hole Reamer (JREAMER) Abrasive Jet Horizontal Drill (JETDRILL). Jet Casing Cutter (JCUTTER).

Download Presentation

TIW CORPORATION A PEARCE INDUSTRIES COMPANY

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. TIW CORPORATION A PEARCE INDUSTRIES COMPANY P.O. Box 35729 Houston, Texas 77235-5729 U. S. A.

  2. TIW Abrasive Jet Drilling System (JETDRILL) • Abrasive Jet Casing Cutter (JCUTTER) • Abrasive Jet Hole Reamer (JREAMER) • Abrasive Jet Horizontal Drill (JETDRILL)

  3. Jet Casing Cutter (JCUTTER) Jet Hole Reamer (JREAMER) Jet Horizontal Drill (JETDRILL) TIW Abrasive Jet Drilling System (JETDRILL)

  4. Well Site Equipment

  5. 400 Bbl Tank (A) Data Lines Hydraulic Compensator (E) (C) Data Unit (H) (F) Pump Unit (B) (F) Hydraulic Unit (D) (D) Mud Tank (G) Well Site Equipment A = Water Supply B = Pump Unit C = Sand Blender D = Densometer E = Compensator F = Hydraulic Unit G = Mud Tank H = Data Unit

  6. Downhole Procedures

  7. Abrasive Jet Casing Cutter(JCUTTER)

  8. Abrasive Jet Casing Cutter(JCUTTER) • Run JCUTTER to casing cutting point • Pump abrasive slurry while rotating and moving cutter up and down • Trip out after cutting casing

  9. Abrasive Jet Hole Reamer(JREAMER)

  10. Run-In After cutting casing run abrasive jet hole reamer (JREAMER)

  11. Extend JREAMER nozzles to correct distance to ream hole

  12. After under-reaming move JREAMER upward to rotate nozzles back into tool cavity trip out of hole

  13. JREAMER (Summary) Run-In Hole Extend Jets & Under-ream Retract Jets Trip out of Hole

  14. JREAMER Reamed Section Ream a 30” dia x 10 ft. section 30” 10 FT.

  15. Abrasive Jet Horizontal Drill(JETDRILL)

  16. JETDRILL Anchor The JETDRILL anchor is set using standard wireline or hydraulic setting tools

  17. ORIENTATION GUIDE JETDRILL Orienting Guide A special guide that orients the JETDRILL to the proper angle for jet drilling is adjusted at the surface UNTAPPED Production

  18. ORIENTATION GUIDE Slot for orientation lug JETDRILL Canister A predetermined length of coiled tubing equal to desired lateral length is run inside a canister and the JETDRILL assembly is then run to bottom on a work string

  19. JETDRILL COLLET • The JETDRILL is oriented in the anchor • Compressive weight engages a COLLET in the anchor UNTAPPED Production

  20. JETDRILL BENDING Additional compressive load actuates a unique articulated section, starting the 90 degree bend in the coil tubing UNTAPPED Production PIN PIVOT

  21. Guide JETDRILL ACTIVATION • The coil tubing is released from the canister by rotating the work string • Jet drilling is initiated while continuing to set weight on the coil tubing • The coil tubing extends through the articulated body as weight is applied at the surface UNTAPPED Production

  22. The jet bits operating at 6,000 to 8,000 psi drill 3 to 4 inch diameter horizontal holes up to 300 ft long, to overcome formation damage and water coning problems, and to tap new production zones TAPPED Production

  23. JETDRILL can be retrieved and re-run at different angles with the same anchor setting NEW TAPPED Production

  24. Giving Multiple Boreholes from One Position Setting Top View Well Bore

  25. JETDRILL Summary • Erode casing section with JCUTTER • Erode 30 in x 10 ft hole section with JREAMER • Set JETDRILL ANCHOR at desired depth • Run JETDRILL and orient in ANCHOR • Apply weight to engage collet in ANCHOR • Release coil tubing by rotation and initiate jet drilling. Continue to set-down weight on coil tubing until desired distance is drilled • Pick up and retrieve JETDRILL assembly from well

  26. JETDRILL Advantages • Convert vertical wells to horizontal • Drill multiple laterals from existing wells • Increase production from existing wells • Penetrate near wellbore damage • Overcome water coning problems • Intersect new production zones • Short radius enables pinpoint accuracy • Patent pending

  27. Setting the Pace in Horizontal Completions

  28. CALL US TODAY!

More Related