1 / 29

1/128 Method Of Calibration Calibrating Hand Sprayers And High Pressure Hand Guns

1/128 Method Of Calibration Calibrating Hand Sprayers And High Pressure Hand Guns. Because a gallon = 128 ounces and the area to be sprayed is 1/128 of an acre, ounces collected = gallons per acre. Step 1.

ashanti
Download Presentation

1/128 Method Of Calibration Calibrating Hand Sprayers And High Pressure Hand Guns

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. 1/128 Method Of CalibrationCalibrating Hand Sprayers And High Pressure Hand Guns • Because a gallon = 128 ounces and the area to be sprayed is 1/128 of an acre, ounces collected = gallons per acre.

  2. Step 1 • Measure out an area equal to 1/128th of an acre. Approximately 340 sq. ft. or an area 18.5 by 18.5 ft. 18.5 ft 18.5 ft

  3. Step 1 • Maybe this shape would work better. 10 ft 34 ft

  4. Step 1 • Or maybe this shape. 1.5 ft 228 ft

  5. The shape of the calibration course is not important. • However, the size of the course must equal 340 sq ft. or 128th of an acre.

  6. Step 2 • Measure the time it takes to spray the measured area. Repeat several times and take the average time.

  7. Step 3 • Spray into a container for the same amount of time it took to spray the measured area. Measure the water collected, in ounces. The amount collected in ounces equals gallons per acre.

  8. EXAMPLE HAND SPRAYER • Step 1. Measure area. 18.5 by 18.5 ft = 340 sq ft • Step 2. Time to spray = 51 seconds • Step 3. Amount collected = 40 ounces • Therefore; 40 ounces = 40 GPA

  9. Determining How Much Pesticide To Add To The Spray Mixture • Recommendation is to apply 1 quart of 2,4-D per acre

  10. The sprayer is applying 40 gallons per acre. Therefore; You will need to add 1 quart of 2,4-D to each 40 gallons of water. • Your sprayer only holds 1 gallon of spray mixture. So how much pesticide will you need to add to the gallon of water?

  11. 1 quart or 32 ounces divided by 40 gallons means that each gallon of water contains 0.8 ounces of 2,4-D. • 1 fluid ounce = 2 tablespoons. Therefore; You will need ~ 2 tablespoons of 2,4-D per gallon of water.

  12. 1 fluid ounce = 30 (cc) or (ml). Therefore; If measuring in cc you would need 0.8 ounces X 30 cc/ounce = 24 cc per gallon of water. • A plastic syringe is an easy and accurate way to measure liquid pesticides.

  13. How large of an area will 1 gallon spray? There are 43,560 ft2/acre. If 40 gallons will spray one acre then one gallon will spray an area 1/40 that size. • 43,560 ft240 • = 1089 ft2.

  14. 1/128 Method Of Calibration • This method of sprayer calibration gives sprayer output in gallons per acre when nozzle discharge is measured in ounces over a course length that = 1/128th of an acre or 340 ft2 MULTIPLE NOZZLE BOOM-TYPE SPRAYERS

  15. Step 1 • Adjust the sprayer pressure and check for uniformity. Operate the sprayer for 1 minute and measure spray from each nozzle. Clean or replace any nozzle that delivers + or - 5% than the output from a new nozzle in good condition.

  16. Step 2 • Measure the spray band width or nozzle spacing in inches on the boom to determine the course length. • The area to be sprayed must equal 1/128th of an acre or 340 ft2 • If the nozzle spacing = 20" then the distance to travel would be 204 ft.

  17. 20" (1.67 ft) X 204 ft = 340 ft2 204 ft 340 ft2 or 1/128 of an acre 1.67 ft

  18. Step 3 • Catch the spray from ONE nozzle while operating the sprayer under field conditions or for the time required to travel the needed distance at a desired speed.

  19. Step 4 • Measure the spray collected in ounces. The number of ounces collected is the same as the number of gallons per acre.

  20. Example • You have a sprayer that has 15 nozzles on a 30 inch spacing. How would you calibrate it using the 1/128th method?

  21. Step 1 • Make sure sprayer is adjusted properly and nozzles are in good working order.

  22. Step 2 • Measure nozzle spacing in inches on the boom to determine the course length. • Using the formula: • 4084 / 30 inches = 136 feet • Or from table 1. W = 30 inches and D = 136 feet

  23. Table 1. Distance (D) to travel and seconds required for selected speeds when nozzle coverage is (W) inches. W (in) D (ft) 2 mph 3 mph 20 204 70 seconds 46 seconds 24 170 58 39 26 157 54 36 28 146 50 33 30 136 46 31

  24. Step 3 • Time how long it takes to travel the 136 ft at a desired speed. Travel this distance several times and get an average time. • Perhaps it takes an average of 31 seconds to travel the 136 feet.

  25. Step 4 • Collect the spray from ONE nozzle in a container for 31 seconds. • Measure the water collected in ounces. • The amount collected in ounces equals gallons per acre. • If in 31 seconds you collected 20 ounces your sprayer output would be 20 gallons per acre.

  26. Determining How Much Pesticide To Add To The Spray Mixture • The recommendation from the label is to apply 1 quart of 2,4-D per acre.

  27. The sprayer is applying 20 gallons per acre. • Therefore; You will need to add 1 quart of 2,4-D to each 20 gallons of water.

  28. Your sprayer holds 200 gallons. So how much pesticide will you need to add to the 200 gallon spray tank? • 200 gallons divided by 1 qt 2,4-D per 20 gallons water = 10 quarts of 2,4-D per tank

  29. How large an area can be sprayed by your 200 gallon tank? • 200 gallons divided by 20 gallons per acre = 10 acres

More Related