1 / 30

Meandering channels in laboratory flumes Christian Braudrick with Bill Dietrich, Leonard Sklar, Glen Leverich

2. Problem. Bars are essentially passive in current meandering models and they therefore the models cannot be used to predict channel response to changes in discharge or sediment supplyCreating meandering channels in the laboratory has proven difficult without strength channels braid, channels with

aoife
Download Presentation

Meandering channels in laboratory flumes Christian Braudrick with Bill Dietrich, Leonard Sklar, Glen Leverich

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


    1. 1

    2. 2 Problem Bars are essentially passive in current meandering models and they therefore the models cannot be used to predict channel response to changes in discharge or sediment supply Creating meandering channels in the laboratory has proven difficult without strength channels braid, channels with cohesive materials stop migrating Bank erosion occurs faster than bars can create new floodplain Open chutes on the inside of bars are the locus for braiding

    3. 3 Outline Experimental design and methods Experiments on the necessary conditions for meandering Experiments on bar morphology and sediment supply Ongoing experiments at RFS Experiments at OSL What next

    4. 4 Hypotheses If slope, discharge, and channel dimensions are appropriate (following Parker, 1977), gravel-bed meanders also require: Bank strength to slow bank erosion to allow time for the bars to grow Fine sediment (sand) to fill chutes and the downstream end of bars Overbank flows to allow the bar to grow to the floodplain elevation

    5. 5 Hypotheses If slope, discharge, and channel dimensions are appropriate (following Parker, 1977), gravel-bed meanders also require: Bank strength to slow bank erosion to allow time for the bars to grow - Provided by alfalfa sprouts Fine sediment (sand) to fill chutes and the downstream end of bars Lightweight plastic sediment Overbank flows to allow the bar to grow to the floodplain elevation - Test both a variable hydrograph and a steady hydrograph

    6. 6 Experimental conditions Flume is 16.5 m long and 6.1 m wide Basin slope = 0.0046 Basin filled with sand with a D50 of 0.85 mm Initial channel geometry = 40 cm X 1.9 cm Froude number = 0.55, Reynolds number = 4500 Feed sand (scaled gravel) and lightweight plastic (scaled sand)

    7. 7 Measurements Coarse and fine feed fed independently Discharge measured with a v-notch weir Topography measured with laser-camera system Overhead cameras record position every five minutes Water surface profiles measured with point gauges (now using TiO2 and laser-camera system) Velocity measured with both floats, dyes Load cell to measure sediment flux at the downstream end (did not work in first experiment).

    8. 8 The life cycle of alfalfa at RFS Seed flume with low flow on Water by hand and with low flow until seeds germinate After germination turn on grow lights-12-14 hours a day From seed to sprout takes about one week Alfalfa starts to die after about 20 hours of run time (over the course of about 3 days) After the alfalfa dies, start over again Building too cold in winter for alfalfa

    9. 9 The experiment Consists of a 71 hour, variable peak hydrograph (1.8 + 2.7 l/s + early tests up to 4.5 l/s) and a 64 hour steady peak hydrograph (1.8 l/s) The variable experiments used plastic feed with a median diameter of 350 microns and specific gravity=1.5 The steady flow experiments used plastic feed with a median diameter of 350 microns and specific gravity=1.3 Sprouts seeded at ~1.2 sprouts/cm2 Coarse feed turned off periodically to prevent aggradation at upstream end of the flume

    10. 10 Time-lapse video

    11. 11 Bars migrated both downstream and laterally Curvature developed from upstream to downstream Curvature redeveloped following cutoffs The bend wavelength was about 14 channel widths

    12. 12 Width stabilized after 40 hours High flow tests caused channel width to increase Sinuosity increased in first 50 hours, and reached a quasi-steady value Meandering maintained during steady peak flow, but flow was overbank

    13. 13 Sediment dynamics

    14. 14 Close up of a bar

    15. 15 Comparing migration rates to the field- Time scaling

    16. 16 Bank migration rates were very fast

    17. 17

    18. 18 Summary of necessary conditions experiments We were able to create a self-formed, single-thread meandering channel that maintained a stable width Meandering was maintained under the steady peak flow conditions, but the flow was slightly overbank Channel geometry was similar to channels in the field The channel cut off five times and rebuilt curvature after cutoffs Cutoffs limited sinuosity development, sinuosity was a maximum of just under 1.2 Fine sediment was crucial-filled the downstream end of bars, plugged chutes, and plugged cut off channels Bank migration rates were very fast relative to channels in the field

    19. 19 What next? How does sediment supply affect bar morphology and migration rate We want to test the hypothesis that increased topographic steering-induced stress alters bar morphology. Use alternate bars, bars in sinuous fixed bank streams, and the meandering flume. We hypothesize that increased supply will cause bars to grow and increase the area of topographic steering, while decreased stress will decrease the area of topographic steering With the Barflies, modify an existing hydrodynamic model (MD_SWMS) to include supply effects, and provide data to test the model

    20. 20 Ongoing experiments RFS Can we increase the sinuosity by changing the bank strength to slow down erosion? Increase bank strength by increasing the alfalfa density by 2.5-3X (2.8-3.5 sprouts/cm2) Increase discharge to increase sediment flux Increase discharge to increase bank stress (to still get erosion) (Qw=2.6 l/s) Start with a sinuous channel Two runs with similar conditions- Run 1-sediment feed error caused aggradation Run 2-excavated existing channel

    21. 21

    22. 22

    23. 23

    24. 24

    25. 25

    26. 26 Ongoing experiments RFS Higher bank strength (and slower erosion rates) limited chute development The sinuosity increased (up to 1.5), with erosion focused just downstream of the bar apex We are struggling with continued aggradation in the middle of the flume. Will get in one more run prior to freeze up.

    27. 27 OSL experiments with Susannah Erwin, Peter Wilcock, Anne Lightbody, Kristen Sweeney, and Dan Mielke This Fall we conducted a test of supply and bar morphology linkages at the OSL. Flume experiments at field scale. We measured topographic response going from no supply, to a moderate supply, to a ~5X increase in supply and back to moderate supply again Other measurements include velocity, water surface elevation, sediment flux, and grain size data. Here, I will just show some preliminary data

    28. 28

    29. 29

    30. 30 Preliminary Results The bar shrank considerably when supply was turned off (not shown) Turning on the supply created a bar that extended around the middle three cross section, with a trough on the inside edge of the bar Increasing the supply by ~5 times caused the bar to extend upstream and downstream. The bar swelled, the pool shallowed 10-15 cm, and the trough to disappear

    31. 31 What next Create a self-formed channel in meandering flume and insert fixed walls to test bar response to changes in supply-may need to decrease alfalfa density somewhat Test the effect of increased supply on alternate bars at RFS straight flume-is 5X too large a supply increase? Working with the bar flies, provide data to modify MD_SWMS (a quasi 3-d hydraulic model) to include supply effects

More Related