KX-TD500 Technical Training Seminar. Table of Contents. Introduction 1-7 KX-TD500 Basic and Expansion Shelf 8-19 Configuration 20-23 CPU Card KX-TD50101 24-27 TSW Card KX-TD50102 28-32 KX-TD500 Cards 33-59 Activity One 60 System Startup 61-65 Activity Two 66
Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author.While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server.
KX-TD500 Basic and Expansion Shelf 8-19
CPU Card KX-TD50101 24-27
TSW Card KX-TD50102 28-32
KX-TD500 Cards 33-59
Activity One 60
System Startup 61-65
Activity Two 66
Hardware Addresses 67-73
Port Status 74-79
Maintenance Console Software 80-90
Activity Three 91
Activity Four 92-98
Activity Five 99
Activity Six 100
Activity Seven 101-102
Activity Eight 123-128
Activity Nine 129
Final system configuration of (48) CO lines and (448)
extensions (320 DPT & (128) SLT) = (496) Total
Final system configuration of 192 T1 channels and 256
DPT extensions 448 Total
Purpose: To assemble a shelf and install cards in a shelf
1. Install an Expansion Shelf on a Basic Shelf
2. Install all cards into the Basic Shelf leaving slots 09 and 10 empty. Also make sure that slot 01 has either a DLC or DHLC installed in it. This will be necessary for practice exercises at a later time.
1.Ensure that all cards that are to be initially installed are properly seated in the card slots and that the cabinets are properly assembled.
2.Connect the AC power cord to the Basic Shelf and then to a properly grounded and protected AC outlet
3.Connect a ground wire to the Ground terminal (Not necessary in training environment)
4.Turn On the Main Power Switch on the Basic Shelf
5.Turn On the Power Switch for each Expansion Shelf
6. Turn On the Power Switch for the Basic Shelf
7. Using a small flathead screwdriver, turn the Mode Switch on the CPU to position “5”. Note: Leave the System in position 0
8.Press and release the CPU Reset button
9.Wait 2 minutes. After 2 minutes, the Run light will be green and the Off-line light will slowly flash yellow.
10.The system is now in the Off-line mode. Only system administration can be performed.
11.Turn the Mode Switch to position “1”. It is very important that the Mode Switch be placed in position ”1” at this time. If the system were to be reset, or if the AC power were to be lost momentarily, the system would re-initialize and return to the default condition. Any programming changes that you may have been made would have been lost.
12.To place the system into the On-line Mode, press and release the CPU Reset button.
13.Wait 2 minutes. After the 2 minute waiting period, the system will be On-line. The Run light will be lit, and the Off-line and Alarm light will be off. Call processing can be accomplish as well as system administration in the On-line mode. Only the Upload to PBX function can not be performed
Purpose: To become familiar with the system startup procedure
1. Execute the system startup procedure
Purpose: To become familiar with the process of installing the KX-TD500 Maintenance Console program in your PC
1. Install the KX-TD500 Maintenance Console software into your PC.
Purpose: To become familiar with the Maintenance Console program by connecting and disconnecting, navigating, making basic programming changes and applying them.
1. Properly connect your serial cable and null modem connector to your PC and KX-TD500 programming RS-232C
2. Open the KX-TD500 Maintenance Console program
3. Establish a local connection using the default parameters of:
Port Set according to your PC
NL Code CR+LF
Baud Rate 9600 bps
4. Enter Programming-Interactive and allow the software to upload programming parameters
5. Browse through all available programming screens but do not change any parameters at this time.
6. Now make your first programming changes. Ensure that a KX-T7436 is installed on the first port (ext.1001) of the DHLC or DLC installed in slot 01. In the Line-Extension Line screen, program and apply extension 1001 to have the following CO Keys:
CO 1-6 PDN buttons
CO 7-14 S-CO buttons for the 1st 8 CO’s
CO 15-24 Not Stored (for now)
7. Next, program and apply another extension to have the following CO Keys:
CO 1-8 Single-CO
CO 9-18 Not Stored (for now)
CO 19-20 One-Touch buttons
CO 21-24 Not Stored (for now)
8. Now copy all parameters from the above extension to all other extension other than extension 1001 that was programmed in step 6.
9. Name the first 24 extensions
10. Set the Time and Date
11. In the Line-Trunk Line screen, name the first 8 CO’s and assign the Day and Night Destination to be 1001
12. In the Features-System Speed Dialing screen, assign 20 System Speed Dialing names and numbers
13. In the System-System Options 4/4, change the FWD/DND lamp pattern to FWD:On, DND:Flash
14. Test the operation of all applicable programming to this point.
This completes some of the basic programming changes in the interactive mode, now let’s save this configuration to the hard disk drive and make some additional changes to the file in the batch mode.
15. Execute the File-Download from PBX menu option
16. When the Download from PBX is complete, save the file using the Save As menu option to your hard disk drive.
17. Disconnect from the PBX
Now we will modify the file while not connected to the PBX. The changes that are made will be saved to the hard disk when complete. We will then Upload the changes to the KX-TD500
18. Using the File-Open menu option, open the file that you saved in step 16
19. In the Configuration-Extension Port Assignment screen, set the XDP function for all extensions on the DHLC(s)
20. Select a port on a DLC installed in your system and assign it as a DSS in the Configuration-Extension Port Assignment screen. Pair the DSS with extension 1001
21. In the Line-DSS Console screen, assign 32 DSS keys to the DSS console
Now let’s save the file again to the hard disk drive and then Upload the modified file back into the KX-TD500
22. Save the modified file to the hard disk drive once again
23. Using the rotary Mode Switch on the CPU card, place the system in the Off-Line Mode
24. Establish a Local Connection once again
25. Open the saved file
26. Execute the File-Upload to PBX menu option
27. When Upload is complete, disconnect the local connection
28. Using the rotary Mode Switch on the CPU card, place the system in the On-Line Mode
29. Establish a Local Connection once again and enter Interactive programming
30. Confirm the programming that was completed in step 19-21
Purpose: To understand the KX-TD500 toll restriction capabilities
1.Restrict extension 1001 and 1002 from dialing 1-900, 976, 1***976, 011 and 1-411. Allow all other calls.
2. Allow extension 1003 to dial local calls and 1-800 calls only.
Purpose: To understand the KX-TD500 Automatic Route Selection capabilities
1. Using ARS, route all outgoing CO calls over the LCOT in Trunk Group 1.
Purpose: To understand the programming involved in integrating a Panasonic Voice Processing System using DPITS integration.
1. Make the required physical connections between your KX-TD500 and the Voice Processing System for a 2 port DPITS integrated system. This will require that one data pair from an extension port of the KX-TD500 be wired into the input jacks of the VPS using a modular cord.
2. In the Configuration-Extension Port Assignment screen, assign the extension port selected in step 1 to be VPS(DPT)
3. In the Configuration-VPS(DPT) Port Assignment screen, assign the correct VPS Card, VPS Type, Port No. and DN and Group No. for Ext. No. 1 and 2.
4. Connect your PC to the VPS’ s RS-232C, start your communication software, and default the VPS
5. Run the VPS’s Quick Setup Utility
6. Confirm by dialing the VPS port DN that DPITS integration has been achieved.
* Certain line code and frame selections can reduce the available bandwidth from 64 to 56 Kbps
bits per word x 8
samples/sec x 8000
user data 1,536,000 bps
frame bits + 8000
line speed 1,544,000 bps
0 1 1 0 0 1 0 0
0 1 1 0 0 1 0 0
1 0 0 0 0 0 0 0 0
1 0 0 0 B 1 0 B 1
B = Bipoalar Violation
Purpose: To become familiar with the installation of a T1 cards in the KX-TD500 and to be able to program the system accordingly. One T1 line has been installed at your location with the following configuration:
Line Coding B8ZS
Channels 01-12 LCO See workstation notes for numbers
Channels 13-20 GCO See workstation notes for numbers
Channels 21-24 DID (E&M Immediate with DID enabled)
DID digits transferred = Last four See workstation notes for numbers
1. Install a KX-T96187 card in slot 09. Refer to Installation Manual page 2-52, confirm SW5 (jumper) is in the correct position for the KX-TD500.
2. In the Configuration-Slot Assignment screen, assign a T1 card in slot 09
3. In the Configuration-Slot Assignment screen, click on slot 09 T1, and the Properties. Ensure the Line Coding and Frame Sequence is set to B8ZS and ESF.
4. In the Configuration-Slot Assignment screen, click on slot 14 TSW. Set the Clock Configuration Mode to External and Clock Configuration Priority to 109:T1
5. Change the Status to INS
6. Connect the T1 line to the NET jack of the CSU. Connect the RJ-48C cable to the T1 card, the other end to the CPE jack of the CSU
7. Using the display and the four front panel buttons on the CSU, verify that in the CONFIG-NETWORK (NI) display that the Format and Code are set to ESF and B8ZS
8. The CSU Power LED should be lit and all other LED’s are off. The SYNC LED on the KX-TD96187 should flash slowly. If this is not the case, check the CSU and Configuration-Slot Assignment settings.
9. Now, in the Configuration-T1 Port Assignment screen, assign the proper Channel Type
Channels 01-12 LCO Trunk Group 02
Channels 13-20 GCO Trunk Group 03
Channels 21-24 TIE (E&M) Trunk Group 04
10. Place each channel INS
11. On extension 1001, assign eight Single-CO buttons to CO Keys 15-22 for Trunk Lines 10901-10904, and 10913-10916. Verify that you are able to draw dial tone for each of these lines.
12. Set up a ringing pattern of your choice for each of these lines and test
13. In the Line-Trunk Line screens for 10921-10924, verify that the Incoming Type is set to “TIE”, the DID/TIE-Delete Digits is set to “O Digit”, Insert Dial is blank, and the Start Signal Type is “Immediate.”
14. Using the DID addresses provided at your work station, seize a Single-CO and make test calls to verify that the the extension that rings has the matching extension number of the last four digits of the number dialed. When other workstations are ready to receive test T1 DID type calls, make calls from workstation to workstation.
15. Change the ARS routing so that the T1 channels (Trunk Group 2) are seized as a first priority for outgoing calls, and the LCOT in trunk group 1 are seized as a second priority.
Purpose: To become familiar with the process of running diagnostic tests and checking status and error logs
1. Run various diagnostic test
2. Check the error and status screens