Certified Technology Specialist (CTS) PDF Dumps

1. Download Valid Certified Technology Specialist CTS Dumps for Preparation Exam : CTS Title : Certified Technology Specialist https://www.passcert.com/CTS.html 1 / 8

2. Download Valid Certified Technology Specialist CTS Dumps for Preparation 1.Refer to the exhibit. According to the Gantt chart pictured, the Project Manager should wait to start Activity C until which predecessor has been reached? A. Week 3 B. Week 4 C. Activity B D. Milestone X Answer: D 2.As part of a service agreement offering, wfwt PRIMARY role do preventive maintenance visits (PM/PMV) play? A. allows the AV provider toclean, service and assess equipment In the field on a regular basis B. allows the AV provider to check in with customer and serves as an opportunity to sell further solutions C. allows the AV provider tosell a service that is often forgotten by the customer, and therefore generate greater profit D. allows the AV provider access to client premises and scope future work Answer: A 3.Which frequencies are amplified by a subwoofer? A. lowest B. mid-low C. mid-high D. highest Answer: A 4.HOTSPOT Which section of the Ohm's Law chart should be used to calculate values expressed in Ohms? Select the answer by clicking anywhere within the correct quadrant. 2 / 8

3. Download Valid Certified Technology Specialist CTS Dumps for Preparation Answer: 3 / 8

4. Download Valid Certified Technology Specialist CTS Dumps for Preparation 5.When doing a site survey, it is MOST IMPORTANT to consider the client's A. budget. B. timeline. C. expectations. D. knowledge of technology. Answer: C 6.As the height of a character increases on a display. A. legibility increases. B. legibility decreases. C. brightness increases. D. brightness decreases. Answer: A 7.Assuming that the speakers in the picture on the LEFT are 8 Q drivers, what is the impedance of the speaker system on the left? 4 / 8

5. Download Valid Certified Technology Specialist CTS Dumps for Preparation A. 2Q B. 4Q C. 8Q D. 16Q Answer: A 8.During a routine service visit, an engineer notices an LED indicator on a projector's front panel blinking regularly. What should be done? A. consult the projector's manual B. replace the projector's lamp and filters C. disregard because the projector is operational D. remove the power cable and re-boot the projector Answer: A 9.When connecting a condenser microphone, what MUST be included in die system design for it to operate? A. mixer B. stand C. transmitter D. power source Answer: D 10.When creating an estimate for a request for proposal (RFP), what is the FIRST tiling that should be done? A. obtain the costs B. create the submittal C. schedule a site visit D. read the project description Answer: D 11.Network Quality of Service (QoS) is defined as A. the ability to prioritize the traffic in the network system. B. the ability to set the quantity of stations connected via the network. 5 / 8

6. Download Valid Certified Technology Specialist CTS Dumps for Preparation C. the ability to remotely manage network switches, routers and hubs via the network connection. D. a feature allowing the network administrator to monitor who is connected to the network at any given time. Answer: A 12.A saeen is 144 in (3658 mm) wide and the throw ratio is 2.3:1. How far from the screen should the projector be placed? A. 288 In (7303 mm) B. 302 in (7681 mm) C. 331 in (8413 mm) D. 446 in (11339 mm) Answer: C 13.Which method of control is supported by HDBaseT? A. PCIE B. DAU C. RS-232 D. DMX512 Answer: C 14.During project delivery and after completion, it is important to ensure correct management of control system code so that A. programming costs will be within project budget. B. other contractors are unable to reuse or edit code. C. the most up-to-date version of code is available for upload when required. D. sub-contract programmers submit uncompiled code as per their contract of employment. Answer: C 15.Assuming a 10' (3 m) ceiling, what is the approximate volume of this room? 6 / 8

7. Download Valid Certified Technology Specialist CTS Dumps for Preparation A. 300 cubic ft (8.5 m3) B. 600 cubic ft (17 m3) C. 1500 cubic ft (42.5 m3) o D. 6000 cubic ft (162 m3) Answer: D 16.The BEST way to ensure that a project is on budget is to A. calculate the number of calendars days remaining to completion. B. visit the job site and determine the percentage of work completed. C. ask the installation team to estimate remaining work to completion. D. review accrued labor and material costs against remaining work. Answer: D 17.Maintaining AV operations includes which of the following? A. conforming to DISCAS B. measuring system SPL C. updating control system firmware D. comparing NAG and PAG calculations Answer: C 18.How frequently should a personal fall arrest harness be inspected? A. weekly 7 / 8

8. Download Valid Certified Technology Specialist CTS Dumps for Preparation B. before each use C. at the beginning of each project D. at the beginning of each work day Answer: B 19.When discussing a proposed audiovisual project with a new customer, it is important for the salesperson to FIRST A. conduct a survey of end users to determine the project goals. B. prepare a detailed layout of the equipment and cabling requirements. C. identify the key decision makers and stakeholders in the client's organization. D. consult with the project manager to determine the availability of staff to complete the installation. Answer: C 20.Project documentation states the system must logically Isolate control and media networks. What piece of network equipment should be used? A. router B. access point C. managed switch D. unmanaged switch Answer: C 21.To help end users remember key points of the training, the training documentation should include A. equipment datasheets. B. a customized quick start guide. C. user manuals for each piece of equipment. D. instructions for maintaining system input devices. Answer: B 22.When an audio device can no longer accurately reproduce the audio signal, It is called A. feedback. B. dithering. C. distortion. D. saturation. Answer: C 23.Which kind of drawing should a technician refer to in order to determine how to hang a loudspeaker line array? A. detail B. section C. elevation D. reflected ceiling plan Answer: B 8 / 8