Leads4Pass 300-410 exam practice questions 2024

1. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download 300-410Q&As Implementing Cisco Enterprise Advanced Routing and Services (ENARSI) (Include 2023 Newest Simulation Labs) Pass Cisco 300-410 Exam with 100% Guarantee Free Download Real Questions & Answers PDF and VCE file from: https://www.leads4pass.com/300-410.html 100% Passing Guarantee 100% Money Back Assurance Following Questions and Answers are all new published by Cisco Official Exam Center 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 1 / 15

2. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download QUESTION 1 You have two routers connected to each other that are both running the EIGRP protocol. The routers have built a neighbor relationship and are exchanging routing information. You execute the following command on the EIGRP process on Router 1: router1(config)# router eigrp 100 router1(config-router)# passive-interface What will be the effect of this command? A. Only routing advertisements from Router 1 to Router 2 will be prevented. B. Only router advertisements to and from Router 1 will be prevented. C. All hellos and routing updates will be prevented, and the neighbor relationship between Router 1 and Router 2 will be broken. D. Hellos will be prevented, but routing updates will continue to be sent out. Correct Answer: C The effect of the passive-interface command is dependent on the routing protocol. With RIP, the command prevents the sending of route updates, but does not prevent the reception of route updates. With EIGRP, the passive-interface command prevents both the sending and receiving of route updates, and also the sending of hellos. Without hello packets, the routers are unable to maintain the neighbor relationship, upon which all communications including route updates depend. If the intent was to preventing routing updates from Router 1 to Router 2 while still allowing updates from Router 2 to Router 1, the routing updates must be filtered out and denied on Router 1 with a distribute list, as shown in the following command set: router1(config)access-list 101 deny any router1(config)#router eigrp 100 router1(config-router)distribute-list 101 out Objective: Layer 3 Technologies Sub-Objective: Troubleshoot passive interfaces References: Cisco IOS Master Command List, Release 12.4T > p through r > passive-interface Cisco > Home > Support > Technology Support > IP > IP Routing > Design > Design Technotes > Filtering Routing Updates on Distance Vector IP Routing 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 2 / 15

3. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download Protocols QUESTION 2 The IPv6 network is under attack by an unknown source that is neither in the binding table nor learned through neighbor discovery. Which feature helps prevent the attack? A. IPv6 Destination Guard B. IPv6 Prefix Guard C. IPv6 Router Advertisement Guard D. IPv6 Snooping Correct Answer: B The IPv6 Prefix Guard feature works within the IPv6 Source Guard feature and enables a device to reject traffic originating from addresses that are topologically incorrect. QUESTION 3 What is a function of an end device configured with DHCPv6 guard? A. If it is configured as a server, only prefix assignments are permitted. B. If it is configured as a relay agent, only prefix assignments are permitted. C. If it is configured as a client, messages are switched regardless of the assigned role. D. If it is configured as a client, only DHCP requests are permitted. Correct Answer: C The DHCPv6 Guard feature blocks reply and advertisement messages that come from unauthorized DHCP servers and relay agents. Packets are classified into one of the three DHCP type messages. All client messages are always switched regardless of device role. DHCP server messages are only processed further if the device role is set to server. Further processing of server messages includes DHCP server advertisements (for source validation and server preference) and DHCP server replies (for permitted prefixes). If the device is configured as a DHCP server, all the messages need to be switched, regardless of the device role configuration. QUESTION 4 The network administrator configured the router for Control Plane Policing to limit OSPF traffic to be policed to 1 Mbps. Any traffic that exceeds this limit must also be allowed at this point for traffic analysis. The router configuration is: access-list 100 permit ospf any any ! class-map CM-OSPF match access-group 100 ! policy-map PM-COPP class CM- OSPF police 1000000 conform-action transmit ! control-plane service-policy output PM-COPP The Control Plane Policing failed to monitor and police OSPF traffic. Which configuration resolves this issue? 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 3 / 15

4. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download A. policy-map PM-COPP class CM-OSPF no police 1000000 conform-action transmit police 1000000 conform-action transmit exceed-action transmit ! control-plane no service-policy output PM-COPP B. policy-map PM-COPP class CM-OSPF no police 1000000 conform-action transmit police 1000000 conform-action transmit exceed-action transmit C. control-plane no service-policy output PM-COPP service-policy input PM-COPP D. no access-list 100 access-list 100 deny ospf any any access-list 100 permit ip any any ! policy-map PM-COPP class CM-OSPF no police 1000000 conform-action transmit police 1000000 conform-action transmit exceed-action drop ! control-plane no service-policy output PM-COPP service-policy input PM-COPP Correct Answer: C QUESTION 5 Refer to the exhibit. 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 4 / 15

5. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download After configuring OSPF in R1, some external destinations in the network became unreachable. Which action resolves the issue? A. Clear the OSPF process on R1 to flush stale LSAs sent by other routers. B. Change the R1 router ID from 10.255.255.1 to a unique value and clear the process. C. Increase the SPF delay interval on R1 to synchronize routes. D. Disconnect the router with the OSPF router ID 0.0.0.0 from the network. Correct Answer: B 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 5 / 15

6. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download QUESTION 6 Refer to the exhibit. Which action installs route 192.168.2.2/32 in the routing table? A. Redistribute connected networks into BGP on the local router. B. Configure NAT on the local router to translate private IP addresses. C. Configure the next-hop-self attribute for the peering on the local router. D. Configure the next-hop-self attribute for the peering on the peer router. Correct Answer: D QUESTION 7 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 6 / 15

7. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download Refer to the exhibit. 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 7 / 15

8. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 8 / 15

9. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download Which two actions restrict access to router R1 by SSH? (Choose two.) A. Remove class-map ANY from service-policy CoPP. B. Configure transport output ssh on line vty and remove sequence 20 from access list 100. C. Configure transport input ssh on line vty and remove sequence 30 from access list 100. D. Remove sequence 10 from access list 100 and add sequence 20 deny tcp any any eq telnet to access list 199. E. Configure transport output ssh on line vty and remove sequence 10 from access list 199. Correct Answer: BC To only allow SSH to R1, we have to: + Deny Telnet in ACL 100 because the action of class-map: PERMIT is "permit" + Permit Telnet in ACL 199 because the action of class-map: ANY is "drop" But: + In ACL 100 there is a permit statement for Telnet traffic "20 permit tcp any any eq telnet (5 matches)" which is not correct so we must remove this statement. + In ACL 199 there is an ACL statement "10 deny tcp any eq telnet any (50 matches)". This statement is aimed for Telnet traffic leaving R1 which is not correct so we must remove this statement. Note: + The command "transport output telnet ssh" allows telnet and SSH from this device (to other devices). + Telnet is TCP port 23. + When using Telnet on source port, it affects Telnet traffic leaving from R1. QUESTION 8 You are configuring NAT64 to allow communication between a host running IPv6 and a server running IPv4. The router R1 sits between the host and the server. The router\\'s Fa0/2/7 interface is connected to the IPv6 host, and the Fa0/2/6 interface is connected to the IPv4 server. The IPv6 host has an IPv6 address of 2001::a00:1/128 and the IPv4 server is at 10.0.0.1. Below is the relevant configuration on R1: When the IPv4 server responds to the IPv6 host, what IPv6 address will be in the source address in the packet? 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 9 / 15

10. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download A. 2001::a001 B. 2001::A00:B C. 3001::a00:1 D. 2001::A00:A Correct Answer: C NAT64 is a solution when IPv6 hosts need to communicate with IPv4-only servers. When the translation occur on the router the IPv4 address 10.0.0.1 will converted to hex as a00:1 and will be attached to the end of the stateful prefix of 3001::/96 that was configured on the router interface connected to the IPv4 server. The result will be 3001::a00:1. The address will not be 2001::a001. The prefix that will be attached to the hex version of 10.0.0.1 will not be that of the interface fa0/2/7 but will be the prefix that was configured on that interface for nat64 translation which is 3301::/96. The address will not be 2001::a00:b. That is the IPv6 address on the interface connected to the IPv6 host, but that address is not used for IPv4 to IPv6 communication. A translated address will be generated by converting the IPv4 address of the IPv4 host to hex and attaching it to the IPv6 prefix configured on the interface connected to the IPv4 server. The address will not be 2001::A00:A. That is the IPv6 address of the IPv6 host. That was statically mapped to 10.0.0.10 in the configuration and as such will be the IPv4 address used by the IPv6 host on the IPv4 side of the router. Objective: Infrastructure Services Sub-Objective: Describe IPv6 NAT References: Stateful Network Address Translation 64 (PDF) QUESTION 9 Refer to the exhibit. 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 10 / 15

11. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download A network administrator successfully logs in to a switch using SSH from a (RADIUS server When the network administrator uses a console port to access the switch the RADIUS server returns shell:priv-lvl=15\\'\\' and the switch asks to enter the enable command \ the command is entered, it gets rejected. Which command set is used to troubleshoot and reserve this issue? A. line con 0 aaa authorization console privl5 ! line vty 0 4 authorization exec B. line con 0 aaa authorization console ! line vty 0 4 authorization exec C. line con 0 aaa authorization console authorization priv15 ! line vty 0 4 transport input ssh D. line con 0 aaa authorization console authorization exec ! line vty 0 4 transport input ssh Correct Answer: D Reference: https://flylib.com/books/en/1.233.1.74/1/ QUESTION 10 The exhibit contains portions of RouterA\\'s BGP configuration and IP routing table. 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 11 / 15

12. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download Which IP network addresses, that were not learned using BGP, will be present in BGP advertisements from RouterA? A. 172.16.0.0/16 B. 172.16.16.0/24 C. 172.16.24.0/20 D. No IGP networks will be advertised because synchronization is disabled. Correct Answer: A The auto-summary command can affect which networks, identified by using the network command, will be advertised. Using the existing BGP configuration, the router will not announce the 172.16.16.0/24 subnet. Instead, it will announce the classful address 172.16.0.0/16 when the IP routing table maintained by the IGP contains any subnet of that classful address. The network command directly affects what network is advertised in BGP. If the network command does not also include a network mask, and if auto-summary is enabled, the classful address of 172.16.0.0/16 is advertised any time that the router learns about a 172.16.0.0 subnet via its Interior Gateway Protocol (IGP), such as OSPF or EIGRP. In the exhibit, the routing table does contain entries of the 172.16.16.0/24 and 172.16.24.0/24 subnets that were learned by using the IGP. If auto-summary is disabled by using the no auto-summary command, only networks in the routing table that are exact matches to the network commands are advertised. For example, to have the router announce only the 172.16.16.0/24 subnet learned via its IGP, you should alter the network command\\'s IP address and include the subnet mask as follows: network 172.16.16.0 mask 255.255.255.0 A combination of network statements and route statements can be used to advertise a subset of networks that exist. Examine the output shown below: router bgp 68410 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 12 / 15

13. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download network 192.168.24.0 255.255.252.0 neighbor 172.16.8.5 remote-as 68441 ip route 192.168.24.0 255.255.252.0 null 0 The router is configured to advertise a summary route to the network 192.168.24.0 255.255.252.0. Consider the following networks: 192.168.24.0/24 192.168.25.0/24 192.168.26.0/24 192.168.32.0/24 If this router was connected to those networks, and received a packet destined for 192.168.25.1, it would successfully route the packet because the summary address (where the summarization is the result of the mask 255.255.252.0) is designed to include all of the subnets above except for 192.168.32.0/24. Therefore, all subnets except 192.168.32.0/24 will be advertised by the network and ip route statements with the summary mask. Note: Whenever changes are made to a routing policy or to an access list that is used by a routing policy, the change will not be reflected in the routing tables of the receiving routers until the BGP session has been cleared with the clear ip bgp command. The BGP synchronization rule specifies that networks will not be advertised or used via iBGP unless it also has been learned through an IGP. If synchronization is disabled, iBGP will advertise a network without also learning it through an IGP. Objective: Layer 3 Technologies Sub-Objective: Configure and verify eBGP (IPv4 and IPv6 address families) References: Cisco IOS Master Command List > a through b > BGP Commands: A through B > auto-summary (BGP) Cisco > Cisco IOS IP Routing: BGP Command Reference > router bgp Cisco > Cisco IOS IP Routing: BGP Command Reference > network (BGP and multiprotocol BGP) QUESTION 11 An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration? A. sudo maglev-config update 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 13 / 15

14. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download B. sudo maglev install config update C. sudo maglev reinstall D. sudo update config install Correct Answer: A QUESTION 12 Refer to the exhibit. The none area 0 routers in OSPF still receive more specific routes of 10.1.1.0.10.1.2.0.10.1.3.0 from area 0. Which action resolves the issue? A. Configure route summarization on OSPF-enabled interfaces. B. Summarize by using the summary-address 10.1.0.0 255.255.252.0 command. C. Summarize by using the area range command on ABRs D. Configure the summary-address 10.1.0.0 255.255.252.0 command under OSPF process. Correct Answer: C QUESTION 13 Refer to the exhibit. An engineer must establish a point-to-point GRE VPN between R1 and the remote site. Which configuration accomplishes the task for the remote site? 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 14 / 15

15. https://www.leads4pass.com/300-410.html 2024 Latest leads4pass 300-410 PDF and VCE dumps Download A. Interface Tunnel1 tunnel source 199.1.1.1 tunnel destination 200.1.1.3 ip address 192.168.1.3 255.255.255.0 B. Interface Tunnel1 tunnel source 200.1.1.3 tunnel destination 199.1.1.1 ip address 192.168.1.1.255.255.255.0 C. Interface Tunnel1 tunnel source 200.1.1.3 tunnel destination 199.1.1.1 ip address 192.168.1.3.255.255.255.0 D. Interface Tunnel lunnel source 199.1.1.1 tunnel destination 200.1.1.3 ip address 192.168.1.1.255.255.255.0 Correct Answer: C 300-410 PDF Dumps 300-410 Study Guide 300-410 Braindumps 300-410 PDF Dumps | 300-410 Study Guide | 300-410 Braindumps 15 / 15 Powered by TCPDF (www.tcpdf.org)