1 / 36

Secure LAN Switching

Secure LAN Switching. Layer 2 security Introduction Port-level controls Storm control Protected ports Private VLAN Port blocking Port security ACLs on switches STP features for layer-2 security DHCP features against snooping IP source guard Dynamic ARP Inspection (DAI).

zulemar
Download Presentation

Secure LAN Switching

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Secure LAN Switching • Layer 2 security • Introduction • Port-level controls • Storm control • Protected ports • Private VLAN • Port blocking • Port security • ACLs on switches • STP features for layer-2 security • DHCP features against snooping • IP source guard • Dynamic ARP Inspection (DAI) Network Security

  2. Switches and Layer 2 security • Security of lower layer devices is important, because some threats are initiated on Layer 2 rather than Layer 3 and above. • Example: A firewall or a router cannot block a compromised server on a DMZ LAN from connecting to another server on the same segment.  because the connection occurs at Layer 2 • Focus of the chapter: Cisco Catalyst series switches (principles applicable to other types of switches) Network Security

  3. Source: http://www.cisco.com/ca/events/pdfs/L2-security-Bootcamp-final.pdf Network Security

  4. Switch and Layer 2 security • Sample L2 attacks and their mitigations See http://www.cisco.com/ca/events/pdfs/L2-security-Bootcamp-final.pdf (local copy) Network Security

  5. Port security • A mechanism to restrict the MAC addresses that can connect via a particular port of the switch • Allows a range of MAC addresses to be specified for a particular port • Only frames with a right MAC address can go through the switch. • Useful for preventing MAC address flooding attacks • CAM overflow: Content-Addressable Memory (aka. associated memory) • CAM table stores information such as MAC addresses available on physical ports, with their associated VLAN params. • CAM table has fixed size. • When a CAM table is full, the switch is unable to create a new entry.  It forwards a received frame to all ports, resulting in increased traffic and allowing the attacker to examine all frames. So, CAM overflow attacks may lead to subsequent DoS and traffic analysis attacks (next slide) Network Security

  6. MAC Address Flooding Network Security

  7. MAC Address Flooding (cont.) • Counter-measures: • Hard-coding the MAC addresses that are allowed to connect on a port, or • Limiting the number of hosts that are allowed to connect on a port • Example 5-1: approach 1 + timed suspension Console> (enable) set port security 2/1 enable Console> (enable) set port security 2/1 enable 00-90-2b-03-34-08 Console> (enable) set port security 2/1 shutdown 600 • Example 5-2: approach 2 Console> (enable) set port security 3/2 maximum 20 Network Security

  8. IP permit lists • Purpose: To restrict higher layer traffic, such asTelnet, SSH, HTTP, and SNMP, from entering a switch • Allows IP addresses to be specified that are allowed to send these kinds of traffic through the switch • Command: set ip permit enable • Example 5-3 Network Security

  9. Protocol Filtering • Purpose: To limit broadcast/multicasts for certain protocols • With Cisco Catalyst 5000 series of switches, packets are classified into protocol groups: • IP 2. IPX • AppleTalk, DECnet, Banyan VINES 4. Other protocols • A port is configured to belong to one or more of these groups. • For each of the groups a port belong to, the port is in one of the following states (for that group): On  Receive all broadcast/multicast traffic for that protocol Off  no broadcast/multicast traffic for that protocol Auto  auto-configured port • The port becomes a member of the protocol group only after the device connected to the port transmits packets of that specific protocol group. • Once the attached device stops transmitting packets for that protocol for 60 minutes, the port is removed form that protocol group. • Example 5-4 Network Security

  10. Controlling LAN floods • Attackers may cause frame flood (e.g., CAM flooding), or send broadcast/multicast messages to flood the LAN. • Counter-measures: • Protocol filtering • Setting up threshold limits for broadcast/multicast traffic on ports • Catalyst switches allow thresholds for broadcast traffic to be set up on a per-port basis. • The thresholds can depend on either the bandwidth consumed by broadcasts or the number of broadcast packets being sent across a port. • ‘Bandwidth consumed’ is a preferred measure. (Why?) • Example: Console> (enable) set port broadcast 2/1-6 75% Other broadcast/multicast traffic is dropped when the bandwidth consumed by broadcast/multicast traffic reaches 75%. Network Security

  11. VLAN • Virtual LAN • Source: http://www.cisco.com/en/US/tech/tk389/tk689/tsd_technology_support_protocol_home.html • Group of devices on one or more LANs that are configured (using management software) so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. • based on logical instead of physical connections • extremely flexible Network Security

  12. Sample VLAN configurations Source: http://www.cisco.com/en/US/products/hw/switches/ps672/products_tech_note09186a0080093dca.shtml#ex1 Network Security

  13. Multiple-VLAN Network Network Security

  14. VLAN & Trunking • A trunk is an interface on a switch that can carry packets for any VLAN. When packets get sent between switches, each packet gets tagged, based on the IEEE standard for passing VLAN packets between bridges, 802.1Q. The receiving switch removes the tag and forwards the packet to the correct port or VLAN in the case of a broadcast packet. • Be aware! “VLAN Insecurity” (by Rik Farrow): http://www.rikfarrow.com/Network/net0103.html “VLANs make it possible to share a switch among many LANs, by filtering and limiting broadcast traffic.” “But this form of isolation relies on software and configuration, not the physical isolation that security people like myself really like to see.” Network Security

  15. Private VLANs • An enhancement to some Cisco switches • Traditional VLAN: no layer 2 segregation of devices of the same VLAN  So when one of the devices in a VLAN is compromised, other devices on the same VLAN may be compromised as well. • Purpose of private VLANs: To allow restrictions to be placed on the Layer 2 traffic of a VLAN. Network Security

  16. Private VLANs • Provides layer 2 isolation to quarantine hosts from one another among ports within the same PVLAN • Three types of private VLAN ports: • Promiscuous ports: communicate with all other private VLAN ports • Community ports: communicate among themselves and with their promiscuous ports • Isolated ports: have complete Layer 2 isolation from other ports within the same private VLAN (e.g., Ethernet ports in hotel rooms) Network Security

  17. Network Security

  18. Other security features in VLAN • Port blocking • When a packet’s MAC address can not be found in a switch’s MAC address table, the switch will broadcast (flood) unknown unicast and multicast traffic to all the ports in the same VLAN • This flooding can be blocked using port blocking feature • Port filtering based on MAC address • A set of MAC addresses are allowed to access a port. • Packets with source MAC addresses outside the set are dropped. Network Security

  19. ACLs on Switches, 1/4 • Router ACL • Switched virtual interfaces (SVI) are virtual layer 3 interfaces. • Both standard and extended ACLs are supported on SVI. • MAC ACL • Aka Ethernet ACL • Filters non-IP traffic using MAC address filtering • Supports only inbound traffic • mac access-list extended Network Security

  20. ACLs on Switches, 2/4 • Port ACL • Supported on physical layer 2 interfaces • Supports only inbound traffic filtering • Supports standard, extended, and MAC-extended ACLs • Can filter both IP and non-IP traffic • VLAN ACL (VACL) • Aka VLAN map • Filters all types of traffic bridged within a VLAN or routed into or out of the VLAN • Examples next page Network Security

  21. ACLs on Switches, 3/4 • VLAN ACL (VACL) • Filters all types of traffic bridged within a VLAN Network Security

  22. ACLs on Switches, 4/4 • VLAN ACL (VACL) • Filters all types of traffic routed into or out of the VLAN • Order of processing: VACL for input VLAN, input IOS ACL, Outbound IOS ACL, VACL for output VLAN Network Security

  23. L2 security using STP features • Spanning Tree Protocol (STP) • Source: http://www.cisco.com/en/US/tech/tk389/tk621/tsd_technology_support_protocol_home.html • prevents loops from being formed when switches or bridges are interconnected via multiple paths. • implements the IEEE 802.1D algorithm by exchanging BPDU messages with other switches to detect loops, and then removes the loop by shutting down selected bridge interfaces. • guarantees that there is one and only one active path between two network devices. Network Security

  24. Illustration of the STP • http://en.wikipedia.org/wiki/Spanning_Tree_Protocol • Root ports vs Designated ports Network Security

  25. The STP PortFast feature • Source: http://www.cisco.com/en/US/tech/tk389/tk621/technologies_tech_note09186a008009482f.shtml • STP configures meshed topology into a loop-free, tree-like topology. • When the link on a bridge port goes up, STP calculation occurs on that port. The result of the calculation is the transition of the port into forwarding or blocking state. The result depends on the position of the port in the network and the STP parameters. • This calculation and transition period usually takes about 30 to 50 seconds. At that time, no user data pass via the port. Some user applications can time out during the period. • In order to allow immediate transition of the port into forwarding state, enable the STP PortFast feature. PortFast immediately transitions the port into STP forwarding mode upon linkup. The port still participates in STP. So if the port is to be a part of the loop, the port eventually transitions into STP blocking mode. Network Security

  26. The STP PortFast feature: vulnerability • Source: http://www.cisco.com/en/US/tech/tk389/tk621/technologies_tech_note09186a008009482f.shtml • As long as the port participates in STP, some device can assume the root bridge function and affect active STP topology. • To assume the root bridge function, the device would be attached to the port and would run STP with a lower bridge priority than that of the current root bridge. • This is a simple form of a denial of service (DoS) attack on the network. The temporary introduction and subsequent removal of STP devices with low (0) bridge priority cause a permanent STP recalculation. Network Security

  27. The STP PortFast feature: vulnerability & mitigation • Source: http://www.cisco.com/en/US/tech/tk389/tk621/technologies_tech_note09186a008009482f.shtml • The STP PortFast BPDU guard enhancement allows network designers to enforce the STP domain borders and keep the active topology predictable. • The devices behind the ports that have STP PortFast enabled are not able to influence the STP topology. • At the reception of BPDUs, the BPDU guard operation disables the port that has PortFast configured. Network Security

  28. L2 security using STP features • BPDU Guard • Bridge protocol data units (BPDU) are messages exchanged btwn bridges using STP to detect loops in a network. • BPDU Guardfeature keeps the active topology predictable and enhances switch network reliability by enforcing the STP domain borders. Network Security

  29. L2 security using STP features • Root Guard • A feature preventing a bridge in a particular network from becoming the root bridge of that network • e.g., enable Root Guard on service provider (SP) side switch interfaces that connect to a customer-side switch  If a switch outside the SP network becomes the root switch, the interface is put in a blocked state, and STP will select a new root switch. • spanning tree guard root Network Security

  30. L2 security using STP features • EtherChannel Guard • “Cisco EtherChannel technology is a trunking technology based on grouping several full-duplex 802.3 Ethernet links to provide fault-tolerant, high-speed links between switches, routers, and servers.” (source: http://www.cisco.com/en/US/tech/tk389/tk213/technologies_white_paper09186a0080092944.shtml) • EtherChannel parameters must be the same on both sides (e.g., btwn a switch and a connected device) • When the switch detects an EtherChannel misconfiguration, the EtherChannel Guard places the switch interface in the error-disabled state Network Security

  31. L2 security using STP features • Loop Guard prevents alternative or root ports from becoming designated ports, thus avoiding loops • http://www.cisco.com/en/US/tech/tk389/tk621/technologies_tech_note09186a0080094640.shtml#loop_guard_description • An STP loop is created when an STP blocking port in a redundant topology erroneously transitions to the forwarding state. • This usually happens because one of the ports of a physically redundant topology (not necessarily the STP blocking port) no longer receives STP BPDUs. In its operation, STP relies on continuous reception or transmission of BPDUs based on the port role. The designated port transmits BPDUs, and the non-designated port receives BPDUs. • When one of the ports in a physically redundant topology no longer receives BPDUs, the STP conceives that the topology is loop free. Eventually, the blocking port from the alternate or backup port becomes designated and moves to a forwarding state. This situation creates a loop. Network Security

  32. DHCP Snooping feature • Protection from rogue DHCP servers • Ports on a switch are divided into trusted and untrusted ports. • DHCP clients and other hosts are connected to the untrusted ports. • DHCP servers are connected to trusted ports. • The switch maintains a DHCP binding database (aka DHCP snooping table). • Incoming packets received on untrusted ports are dropped if the source MAC address does not match the MAC in the binding table. Network Security

  33. IP Source Guard • Protection from IP spoofing attacks when a host tries to spoof and use the IP address of another host • Any IP traffic coming into the interface with a source IP address other than that assigned will be filtered out. Network Security

  34. Dynamic ARP Inspection (DAI) • ARP (address resolution protocol) resolves a 32-bit IP address into a 48-bit Ethernet address, using an ARP Table. • The ARP caches can be “poisoned” (an invalid ARP entry is created in the table). • Result: packet redirection to the attacker • DAI locks down the IP-MAC mapping for hosts so that the attacking ARP is denied and logged. Network Security

  35. Setting up a secure Layer 2 switching environment • Overview of Counter-measures: • Use VLANs to create logical groupings of devices  Each of the groups may have different security levels. • Disable unused ports, and place them in a VLAN with no Layer 3 access. • Besides VLANs, other mechanisms must be used (e.g., port security) • Separate devices should be used for zones at different security levels. • Disable Layer 3 connection (e.g., Telnet, HTTP) to the switch. • Disable trunking on ports that do not require it (and place the trunk port in its own VLAN). Network Security

  36. Need for other counter-measures • How about attacks launched from hosts sitting on a LAN? • In general, those hosts are considered as trusted entities. • So it is difficult to stop a host when it becomes an attacker. • Solution: Make sure access to the LAN is secured.  MAC address filtering (e.g., Cisco’s port security, DHCP) Network Security

More Related