1 / 14

ECE 447 Fall 2009

ECE 447 Fall 2009. Lecture 9: TI MSP430 Interrupts & Low Power Modes. Last Lecture: MSP430 Interrupt Class Exercise.

zubeda
Download Presentation

ECE 447 Fall 2009

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ECE 447 Fall 2009 Lecture 9: TI MSP430 Interrupts & Low Power Modes

  2. Last Lecture: MSP430 Interrupt Class Exercise Write a program that collects samples from input Port 2. A signal line that indicates a new data value is available is connected to pin P1.0. Use an interrupt to detect a rising edge on the P1.0. When an interrupt is triggered the value on Port2 should be stored into a byte array of 32 entries. When 32 samples have been collected, P1.7 should be driven as an output high to indicate the memory is “full”

  3. Lecture 8 Example – Part I #include "io430.h" #include "intrinsics.h" char entries[32]; // Array for storing input from Port 2 (Global Variable) char index; // Index within byte array for Port 2 (Global Variable) void main( void ) { WDTCTL = WDTPW | WDTHOLD; // Stop watchdog timer to prevent time out reset P1DIR = BIT7; // set p1.7 to output P1IE = BIT0; // enable interrupts for p1.0 (default rising edge) __enable_interrupt(); // enable global interrupts index = 0; // initialize the indexer to the beginning of the array for (;;) { __low_power_mode_4(); // go to low power mode } }

  4. Lecture 8 Example – Part II // In the same file as Part I #pragma vector = PORT1_VECTOR __interrupt void p1_isr() { if (!(P1OUT & BIT7)) // Check if Memory is full { entries[index] = P2IN; // store the value on the data port index++; // increment the indexer if (index >= 32) { P1OUT |= BIT7; // set p1.7 high to signal full array } } }

  5. ECE447: MSP430 Non-Maskable Interrupts • An interrupt that cannot be disabled is typically referred to as nonmaskable • Most interrupts in the MSP430 are masked by the GIE bit in the SR and individual control bits. • Some interrupts are not controlled by the GIE, and sometimes referred to as nonmaskable interupts. • However in the MSP430, all interrupts have some bits to be set in order to enable them, even if not masked by the GIE bit in the SR. • All nonmaskable interrupts share a single interrupt vector.

  6. ECE447: MSP430 Handling Interrupts that share an Interrupt Vector • ISR must first identify the source of the interrupt • Service the interrupt and clear as necessary for the source

  7. ECE447: Low Power Modes • The TI MSP430 has four power mode/levels. • Each has different characteristics for: • Memory state • Instruction Execution state • IO state • Timer/Clock state • The MSP430 is highly optimized for low power, further enabled by the proper usage of the low power modes of the device.

  8. ECE447: Low Power Modes - Active Mode • All clocks of the MSP430 are active • MSP430 starts up in this mode, and enters this mode when an interrupt is detected • Only mode where instructions are executing. • Current can range from 200 to 300 µA 0 0 0 0

  9. ECE447: Low Power Modes - LPM0 • LPM0 has the CPU and MCLK disabled. • Used in cases where active peripherals need a high speed SMCLK. • Current is approximately 85 µA 0 0 0 1

  10. ECE447: Low Power Modes - LPM3 • CPU, MCLK, SMCLK, and DCO are disabled • ACLK remains active. • This is the standard low power mode when the MSP430 must awaken itself at regular time intervals, and therefore needs a slow clock. • If the RTC is to be maintained this is the necessary low power mode. • Current is approximately 1 µA 1 1 0 1

  11. ECE447: Low Power Modes - LPM4 • CPU and all clocks are disabled • The MSP430 can only awaken from and external signal. • The mode is know as RAM retention mode • Current is approximately 0.1 µA 1 1 1 1

  12. ECE447: Waking from an LPM (Interrupt Handling) • An interrupt is necessary to exit a LPM. • The MCLK and CPU are started automatically to allow the CPU to service the interrupt. • Since the SR is cleared when an interrupt occurs it is necessary to modify the SR if you wish to return to normal operation after the interrupt service routine exits. • If all processing necessary for service is completed in the interrupt the CPU will return to the low power mode upon exit.

  13. ECE447: Returning to the Main Function from a LPM • To return the Main function after an interrupt wakes the MSP430 from a LPM you must: • Clear all the LPM bits in the SAVED value of SR on the stack. • In C an intrinsic function __low_power_mode_off_on_exit() handles this for you. • In Assembly the programmer must take this burden directly. (The SP will be pointing at the SR on the stack upon entry to the ISR) • Upon exit the modified SR will be restored and normal operation in Active mode will resume.

  14. ECE447: Class Exercise Write a C program that initializes an interrupt on change of input pin P1.4. When the interrupt occurs the input on P2.0-1 will be inverted and output on P1.0-1. When waiting for the interrupt to occur the MSP430 should be in the appropriate LPM that will allow the output to be maintained with the least power consumption.

More Related