1 / 26

CitectSCADA Communications with Mitsubishi FX3U-ENET

CitectSCADA Communications with Mitsubishi FX3U-ENET. Open FX configuartor-EN to define the FX3U-ENET ethernetcard. And Set module nummer  Module 1 = 2de special module at the right side. Operational settings. Select “Binary code” Select “Always wait for open” Give in the IP adress

wyman
Download Presentation

CitectSCADA Communications with Mitsubishi FX3U-ENET

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. CitectSCADA Communications with Mitsubishi FX3U-ENET

  2. Open FX configuartor-EN to define the FX3U-ENET ethernetcard • And Set module nummer  Module 1 = 2de special module at the right side

  3. Operational settings • Select “Binary code” • Select “Always wait for open” • Give in the IP adress • PLC1 192.168.3.1 • PLC2 192.168.3.2 • Check all setting andsave these with End

  4. Operational settings • Define one or more ports as MELSOFT connections for GX IEC Developer and FX configutor-EN • Define a port for CitectSCADA • TCP • Unpassive • Procedure exit (MC) • Portnumber 1300 • Check all setting andsave these with End

  5. Write settings to the FX3U-ENET • Push the Write button • Select the right COM-portto connect to the PLCand press OK • Push the Write button todownload the settings • Set the PLC to stop • Click OK on the message • With Yes the PLC comes back in run • Power the PLC OFF and ON to reset the ethernet card

  6. Diagnose via serial • Push the Diagnostics button • Connection interface is still set to a COM-port • Push the Diagnostics button in this window as well • Select the different diagositics tabs

  7. Diagnose via ethernet • Push the Diagnostics button • Change the transfer setupto the IP adress of this PLC • Push the Diagnostics button in this window as well • Select the different diagositics tabs

  8. GX IEC Developer via ethernet • Select the Ethernet board on the PC side • Select the Ethernet module in thePLC side • Give in the IP adressof the PLC • Set the timeout to 5 sec • Press Connection test • Save these setting by closing all windwos with OK

  9. Operational settings • Define one or more ports as MELSOFT connections for GX IEC Developer and FX configutor-EN • Define a port for CitectSCADA • TCP • Unpassive • Procedure exit (MC) • Portnumber 1300 • Check all setting andsave these with End

  10. Open Citect project en start de Express Communications wizard

  11. Express Communications wizard steps • IOserver • name = IOserver • IOdevice • name = PLC1 • external I/Odevice • Mitsubishi FX Serie FX3UEthernet(TCP/IP) • Adress 255 (host PLC) • IP adress en port are not asked. See next page.

  12. Set IP - and port adress • Open de port settings of PLC1 • Set the special opt-i10.10.10.160 -p1300 • Press replace to save settings (PLC has IP adress 10.10.10.160 and port 1300 open for Citect)

  13. Cluster needed in Citect v7 • Open clusters • Make a cluster and press “Add” • Open I/O servers • Attach your IOServer to a your cluster and press Replace

  14. Open Variable tags and define tags • Define a 16 bits tag • Name = RegD0_PLC1 • Adress = D0 • IO Device Name = PLC1 • Data type = INT • Press add • Define a 16 bits tag • Name = RegX0_PLC1 • Adress = X0 • IO Device Name = PLC1 • Data type = Digtal • Press add

  15. Create a page

  16. Place a register on the page • Past genie • Select libary keyentery • Select parameter2 • Press OK • Set tag • Press OK • Move object and resizeto your wish

  17. Place a register on the page • Set symbol • Place it on the page • Insert a tag • Press OK

  18. Save your page

  19. Check your Communications settings Cluster1 > IOServer > BOARD1 > PORT1_BOARD1 > PLC1 > D0_PLC1 PORT • IP adres ENET192.168.3.1 • Portnumber ENET1300 • Special Opt-i10.10.10.160 –p1300 • Default TCP & BIN IO DEVICE • Adress255 (host) • ProtocolMELSCNET1 Tag = D0_PLC1

  20. Compile your Project

  21. Run Computer setup wizard

  22. Run your project in demo mode • Run your project • Press OK and run in demo mode for 15 minutes • Via menu update pages and select page01

  23. Connect more FX3U-ENET modules • Open de ports • Change • portname to PORT2_BOARD1 • Port Number to 2 • IP adress to 10.10.10.X • Press Add • Open de IOdevices • Change • Name to PLC2 • Number to 2 • Press Add • You have now 2 record of ports and of IOdevices

  24. Define tags of PLC2 • Open the tag RegD0_PLC1 • Change • Name to RegD0_PLC2 • IO Device Name to PLC2 • Press add • Open the tag RegX0_PLC1 • Change • Name to RegX0_PLC2 • IO Device Name = PLC2 • Press add

  25. Add the PLC2 object on the page • Copy the 2 objectfrom PLC1 • Change the tagsof the copiedobjects • Close the pageand save it

  26. Run Citect

More Related