1 / 40

Chapter 4

Chapter 4. 4.1 : Digital Modulation. 4.2 : Digital Transmission. 4.3 : Multiple Access Methods. 4.1 Digital Modulation. Outlines Introduction Information capacity, Bits, Bit Rate, Baud, M-ary Encoding Digital Modulation Techniques - ASK, FSK, PSK, QAM.

warner
Download Presentation

Chapter 4

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Chapter 4 4.1 : Digital Modulation 4.2 : Digital Transmission 4.3 : Multiple Access Methods

  2. 4.1 Digital Modulation Outlines • Introduction • Information capacity, Bits, Bit Rate, Baud, M-ary Encoding • Digital Modulation Techniques - ASK, FSK, PSK, QAM

  3. Introduction to Digital Modulation • Digital modulation • Is the transmittal of digitally modulated analog signals between to or more points in a communications system. • Can be propagated through Earth’s atmosphere and used in wireless communication system - digital radio. • Offer several outstanding advantages over traditional analog system. • Ease of processing • Ease of multiplexing • Noise immunity

  4. Cont’d... • Applications: • Low speed voice band data comm. modems • High speed data transmission systems • Digital microwave & satellite comm. systems • PCS (personal communication systems) telephone

  5. Why digital modulation? • The modulation of digital signals with analogue carriers allows an improvement in signal to noise ratio as compared to analogue modulating schemes.

  6. Important Criteria • High spectral efficiency 2. High power efficiency 3. Robust to multipath 4. Low cost and ease of implementation 5. Low carrier-to-co channel interference ratio 6. Low out-of-band radiation

  7. Cont’d… 7. Constant or near constant envelop 8. Bandwidth Efficiency • Ability to accommodate data within a limited bandwidth • Tradeoff between data rate and pulse width 9. Power Efficiency • To preserve the fidelity of the digital message at low power levels. • Can increase noise immunity by increasing signal power

  8. Forms of Digital Modulation • If the amplitude, V of the carrier is varied proportional to the information signal, a digital modulated signal is called Amplitude Shift Keying (ASK) • If the frequency, f of the carrier is varied proportional to the information signal, a digital modulated signal is called Frequency Shift Keying (FSK)

  9. Cont’d… • If the phase, θ of the carrier is varied proportional to the information signal, a digital modulated signal is called Phase Shift Keying (PSK) • If both the amplitude and the phase, θ of the carrier are varied proportional to the information signal, a digital modulated signal is called Quadrature Amplitude Modulation (QAM)

  10. Cont’d...

  11. Example 1 For the digital message 1101 1100 1010, sketch the waveform for the following: a. ASK b. FSK c. PSK d. QAM

  12. Block Diagram Simplified block diagram of a digital modulation system

  13. Cont’d… • Precoder performs level conversion & encodes incoming data into group of bits that modulate an analog carrier. • Modulated carrier filtered, amplified & transmitted through transmission medium to Rx. • In Rx, the incoming signals filtered, amplified & applied to the demodulator and decoder circuits which extracts the original source information from modulated carrier.

  14. Information Capacity, Bits, Bit Rate, Baud, M-ary Encoding • Information capacity, Bits & Bit Rate • Represents the number of independent symbols that can be carried through a system in a given unit of time. • Basic digital symbol is the binary digit or bit. • Express the information capacity as a bit rate.

  15. Hartley’s Law Where I = information capacity (bps) B = bandwidth (Hz) t = transmission time (s) From the equation, Information capacity is a linear function of bandwidth and transmission time and directly proportional to both.

  16. Shannon’s Formula Where I = information capacity (bps) B = bandwidth (Hz) = signal to noise power ratio (unitless) The higher S/N the better the performance and the higher the information capacity

  17. Example 2 By using the Shannon’s Formula, calculate the information capacity if S/N = 30 dB and B = 2.7 kHz.

  18. Nyquist Sampling Rate • fs is equal or greater than 2fm fs >= 2fm fs = minimum Nyquist sample rate (Hz) fm = maximum analog input frequency (Hz)

  19. Example 3 Determine the Nyquist sample rate for a maximum analog input frequency 7.5 kHz.

  20. M-ary Encoding • It is often advantageous to encode at a level higher than binary where there are more then two conditions possible. • The number of bits necessary to produce a given number of conditions is expressed mathematically as Where N = number of bits necessary M = number of conditions, level or combinations possible with N bits.

  21. Cont’d… • Each symbol represents n bits, and has M signal states, where M = 2N.

  22. Example 4 Find the number of voltage levels which can represent an analog signal with a. 8 bits per sample b. 12 bits per sample

  23. Baud & Minimum BW • Baudrefers to the rate of change of a signal on the transmission medium after encoding and modulation have occurred. Where baud = symbol rate (symbol per second) ts = time of one signaling element @ symbol (seconds)

  24. Cont’d… • Minimum Bandwidth • Using multilevel signaling, the Nyquist formulation for channel capacity Where fb= channel capacity (bps) B = minimum Nyquist bandwidth (Hz) M = number of discrete signal or voltage levels

  25. Cont’d… For B necessary to pass M-ary digitally modulated carriers Where N is the number of bits encoded into each signaling element.

  26. Digital Modulation Techniques • Amplitude Shift Keying (ASK) • Frequency Shift Keying (FSK) • Phase Shift Keying (PSK) • Quadrature Amplitude Modulation (QAM)

  27. Amplitude Shift Keying (ASK) • A binary information signal directly modulates the amplitude of an analog carrier. • Sometimes calledDigital Amplitude Modulation (DAM) Where vask (t) = amplitude shift keying wave vm(t) = digital information signal (volt) A/2 = unmodulated carrier amplitude (volt) ωc = analog carrier radian frequency (rad/s)

  28. Cont’d... Digital Amplitude Modulation

  29. Frequency Shift Keying (FSK) • Called as Binary Frequency Shift Keying (BFSK) • The phase shift in carrier frequency (∆f) is proportional to the amplitude of the binary input signal (vm(t)) and the direction of the shift is determined by the polarity Where vfsk(t) = binary FSK waveform Vc = peak anlog carrier amplitude (volt) fc = analog carrier center frequency (Hz) ∆f = peak shift in analog carrier frequency (Hz) vm(t) = binary input signal (volt)

  30. Cont’d...

  31. Phase Shift Keying (PSK) • Another form of angle-modulated, constant amplitude digital modulation. • Binary digital signal input & limited number of output phases possible. • M-ary digital modulation scheme with the number of output phases defined by M. • The simplest PSK is Binary Phase-Shift Keying (BPSK) • N= 1, M=2 • Two phases possible for carrier with one phase for logic 1 and another phase for logic 0 • The output carrier shifts between two angles separated by 180°

  32. Cont’d... a) Truth Table b) Phasor Diagram c) Constellation Diagram

  33. Cont’d... BPSK Transmitter

  34. Cont’d... BPSK Receiver

  35. Bandwidth Efficiency • Used to compare the performance of one digital modulation technique to another. Bη = Transmission bit rate (bps) Minimum bandwidth (Hz)

  36. Example 5 For 16-PSK system, operating with an information bit rate of 32 kbps, determine: a. Baud b. Minimum bandwidth c. Bandwidth efficiency

  37. CONCLUSION • To decide which modulation method should be used , we need to make considerations of a) Bandwidth b) Speed of Modulation c) Complexity of Hardware

  38. End of Part 1

More Related