1 / 28

LEARNING OUTCOMES

GEOTECHNICAL ENGINEERING ECG 503 LECTURE NOTE 10 TOPIC : 3.0 ANALYSIS AND DESIGN OF RETAINING STRUCTURES 18 SEPTEMBER 2008. LEARNING OUTCOMES. Learning outcomes: At the end of this lecture/week the students would be able to:.

vaughan-cantrell
Download Presentation

LEARNING OUTCOMES

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. GEOTECHNICAL ENGINEERINGECG 503LECTURE NOTE 10 TOPIC : 3.0 ANALYSIS AND DESIGN OF RETAINING STRUCTURES 18 SEPTEMBER 2008

  2. LEARNING OUTCOMES Learning outcomes: At the end of this lecture/week the students would be able to: • Understand natural slope and made engineered soil slope assessment which include rainfall induced failure and role of suction.

  3. TOPIC TO BE COVERED • Braced Excavation – Determination of Forces in Struts • Cofferdam

  4. Synopsis Needs for further trenching, where it carried out, design consideration + analysis of components (design of the elements) Objective Able to design the bracing and other components to support trench excavation. Able to analyzed the design. Trenching normally temporary structure

  5. Design Components : • Select appropriate size of wale, struts, sheet pile or soldier beam • Basis of selection : Based on the estimated lateral earth pressure • Theoretically aspects of lateral pressure :

  6. Pressure Envelope : Class A – Firm clay and flexible wall 0.2H • = unit weight H = height of cut 0.2H H 0.3H

  7. Pressure Envelope : Class B – Stiff to very stiff clay and flexible wall • = unit weight H = height of cut H 0.3H

  8. Pressure Envelope : Class C – Coarse soil dry • = unit weight H = height of cut H 0.2H

  9. d d1 1 P1 d2 / 2 d2 d2 / 2 2 P2 d3 / 2 d3 d3 / 2 P3 3 d4 / 2 d4 d4 / 2 • = Apparent pressure S = Spacing strut c/c 1 = P1 / S (d1 + d2 /2)

  10. Lateral earth pressure varies with depth. Each strut being designed for maximum load to which it is subjected. • Thus, braced cut being designed using apparent pressure diagram determined from measured struts load in the field.

  11. C H • By Peck, a. Sand,  = 0.65HKa b. Clay, soft to medium stiffness where H  4  = H [ 1 – (4c) ] or  = 0.3 H which ever is the bigger

  12. H  = 0.65HKa Pressure Envelope For Sand

  13. 0.25H 0.75H Pressure Envelope For Cuts in Soft to Medium Clay

  14. C 0.25H H  4 0.5H  = 0.2H to 0.4 H Purposely for design, take average 0.25H Pressure Envelope For Cuts in Stiff Clay

  15. Design Procedure • Design procedure to determine strut load : i. Draw the pressure envelope of the propose strut levels (soldiers beam are assumed to be hinged at the strut level, except for the top and bottom ones)

  16. Design Procedure ii. Determine the reaction for the two simple cantilever beam (top and bottom) and all others are simple beam (A, B1, B2, C1, C2 and D) iii. Used the formulae to calculate strut loads PA = (A) (s) PB = (B1 + B2) (s) PC = (C1 + C2) (s) PD = (D) (s)

  17. Design Procedure iv. Knowing the strut load at each level and the intermediate bracing, then select the proper section from steel construction manuals.

  18. EXAMPLE 1 • Draw the earth pressure envelope and determine the strut loads. Strut are placed at 3m c/c 6m 1m • = 18kN/m3 c = 35 kN/m2  = 10 2m 2m 1m 3m 3m 3m 3m 1m

  19. EXAMPLE 2 • A braced cut shown in Figure below were constructed in a cohesionless soil having a unit weight,  = 18.2 kN/m3 and an angle of internal friction,  = 35. The trust located at 3.5m centre-to-centre in a plan. Determine the trust load at levels A, B and C 5m 2m A • = 18.2 kN/m3  = 20 3m B 3m C 1.5m 3.5m 3.5m 3.5m 3.5m

  20. CELLULAR COFFERDAMS • Used to enable construction works in water bound areas eg. rivers, lake and sea • Stability depend mainly on interaction of the soil to fill the cell and the steel sheetpiling.

  21. Contains three basic types which is : a. Circular Cofferdam b. Diaphragm Cofferdam c. Cloverleaf Cofferdam

  22. Design consideration: a. Cell geometry b. Cell fill materials c. Sheet piles

  23. LATERAL EARTH PRESSURE Stability Analysis Worked example 2 : • A concrete gravity wall is shown in Figure below. Determine : • FOS against Overturning • FOS against Sliding • The pressure on the soil at the toe and heel • (Note : Unit weight of concrete is 24kN/m3)

  24. 1 = 30 1 = 16kN/m3 c1 = 0 8 m 2 = 20 2 = 20kN/m3 c2 = 15 kN/m2 1 2 3 6 5 4 3.5 m 1 m 1.5 m 3 m 1.5 m 1.5 m 0.5 m

More Related