1 / 19

& Verification

Effective Sanitation. & Verification. Elements. Environment factors Continuum / continuous improvement Daily Sanitation: Back to basics Sanitation GMP / 7 Steps. Periodic Sanitation: Tear down & heat. Verification of effective sanitation. Environment. Staffing. Turnover:

urban
Download Presentation

& Verification

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Effective Sanitation & Verification

  2. Elements • Environment factors • Continuum / continuous improvement • Daily Sanitation: Back to basics • Sanitation GMP / 7 Steps. • Periodic Sanitation: Tear down & heat. • Verification of effective sanitation.

  3. Environment • Staffing. • Turnover: • Maintaining training & documentation. • Thirds shift dynamics. • Necessity for flexible workforce (call-ins). • Room and Equipment. • HVAC (visibility during sanitation). • Accessibility (can you touch it / see it?). • Keep it simple (can you disassemble without tools?). • Continuum. • Sanitary design + Effective Sanitation + Traffic Patterns + GMPS + Dry/un-cracked flooring.

  4. Lead to Ineffective Sanitation! • Aerosols. • Spraying drains & drain components. • Drains pooling/backing up. • Hollow rollers, fixed sleeved assemblies, concave surfaces. • Cross traffic. • Lack of accessibility. • Biofilms. • Idle equipment (not being used). • Standing moisture.

  5. High pressure water • Compressed air • Control buttons & screens • Bearings • Congestion in RTE area • Cabinets in RTE areas • Traffic patterns • GMP requirements • Sanitation process NOT documented/sequenced. How do you sustain protocols?

  6. Continuous Improvement • Traffic Patterns: (separation between raw & rte, separation between exposed product areas packaging, ..) • GMPS: (is it difficult to do the wrong thing?) • Flooring: (infrastructure maintained) • Sanitary Design: (existing equipment + new) • Effective Sanitation Procedures: (daily & periodic, limitations known and controls in place) Assess where you are at under each of the categories.

  7. Daily & Periodic Sanitation

  8. Dry Clean • Pre-sanitation task completed consistently (floors swept, equipment covered, materials removed,..). • Equipment disassembled to proper level to provide accessibility. • Dry clean completed 1 Hollow member + cracked weld

  9. Rinse until visually free of soils. Use lowest effective pressure to minimize aerosols and condensation. Lower pressure reduces risk of cross contamination and machine damage. Pre Rinse 2 Multiple lap joints

  10. Contact time, concentration, & mechanical action!!! • Daily scrub of product contact surfaces. • Scour framework weekly minimum. • Chemicals are not a substitute for mechanical action. • Work from walls and floor to equipment. Soap & Scrub 3 Traps Nutrients and Bacteria Mass with Protective Film (Slime) • Bacterial Attachment

  11. Order of applications (necessary to reduce cross contamination potential) • Wall/floors then equipment • Avoid drying of chemicals • Mechanical action Soap & Scrub 3

  12. Micro-SIZE Micron (µm) • 1/1,000,000 meter • 39.37 µ-inch Micro-inch(µ-inch) • 1/1,000,000 inch • 0.0254 micron Mold spore (3 µm, 118 µ-inch) Listeria (0.5 µm, 19.7 µ-inch) Yeast (5 µm, 197 µ-inch) Salt (120µm, 4724 µ-inch)

  13. Post Rinse 4 • Low pressure + volume ONLY! • Rinse the walls, the floor, then the equipment. • Minimize spraying the floor once the equipment begins to be rinsed. • Its clean • Clean equipment = proper GMPs. • Condensate & standing moisture removed. • Tools Removed • Preop & sanitize parts that are not accessible once assembled. Remove 5 & Assemble

  14. Inspect 6 • Foam walls & floors with equivalent of 800-1000 ppm of quat. • Flood rinse sanitize equipment. Target contact 30 seconds to 2 minutes. • Do not dilute wall & floor sanitizer prior to 10 minute contact time. Sanitize 7

  15. Periodic Sanitation/ Tear Down for Access

  16. Periodic Sanitation / Heat Steaming(165F for 30 minutes) Dry heat (165F for 4 hours)

  17. Verification

  18. Sanitation Effectiveness Verification • Physical verification • Organoleptic (site, smell, taste) • Step 6 • Microbiological Verification • Bioluminescence / ATP (immediate results) • Aerobic plate count (results in 2-3 days) • Environmental Monitoring. (results in 3-5 days)

  19. Main Points • Continuous assessment & improvement. • Controls for sanitary design limitations. • Sanitation GMP: Providing mechanical action and limiting cross contamination opportunities. • Verify: Bioluminescence (go/no-go), Aerobic Plate Count (trend).

More Related