1 / 21

“ Manufacturing Systems of the Mars Settlement ” Local Steel, Aluminum, and Glass

“ Manufacturing Systems of the Mars Settlement ” Local Steel, Aluminum, and Glass. Damon Ellender Programming Team DamonE@marshome.org. Manufacturing. Local Manufacturing is key to long-term planetary settlement. Requirements. Steel Processing 400kg/day 1500K

tyrell
Download Presentation

“ Manufacturing Systems of the Mars Settlement ” Local Steel, Aluminum, and Glass

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. “Manufacturing Systems of the Mars Settlement”Local Steel, Aluminum, and Glass Damon Ellender Programming Team DamonE@marshome.org

  2. Manufacturing • Local Manufacturing is key to long-term planetary settlement

  3. Requirements • Steel Processing 400kg/day 1500K • Aluminum Processing 25kg/day 1000K • Glass Processing 200kg/day 1200K-1400K • Manufactured Products as needed for construction(i.e. Structural, wire,…) • Dual use or Flexible equipment used where possible

  4. Glass Process • Floated on Tin, Pilkington Process, 2mx4m float tray, made from local brick, covered to protect from dust • Cooled using CO2 in Lehr, 2mx2m, made from local brick. Rollers imported. • Cut into 1m x 1mx5mm glass panels for transport and further cutting. • Located Outdoors

  5. LCC Steel Process • Low Carbon Content (LCC) Steel is better for low temperature application • All products made of 6mm Sheet or cast directly • Provision for Rolling ‘Strip’ depending on size of Steel Batch • Located Outdoors

  6. Strip Caster • 6mm thick x2m wide • Can be outdoors though dust may require enclosed(not pressurized) areas • Pickling could also be done in enclosed area to ensure recovery of acids/caustics.

  7. Typical Strip Casting Process • All products made of 6mm Sheet or cast directly • Provision for Rolling ‘Strip’ depending on size of Steel Batch

  8. Reference Earth Installations

  9. Slab Caster • For Context • Not practical for amount of steel manufactured unless larger sections needed(i.e. rails) • Batch Casting or Direct Chill better alternative

  10. Aluminum Process • Strip Casting possible using same process as Steel • Direct Chill is also possible for Aluminum, not sure for Steel.

  11. Aluminum Direct Chill Casting • Ingots Poured Vertically • Continuous Quench with Water or CO2 • Once Mold is full, valve shuts, and ingot is rotated and pressed out by ram. • Other material could use this process(i.e steel)

  12. Annealing Furnace • Located Outdoors • Capable of 1000K Temperatures • Capable of Controlled Cooling(using CO2) • Approximately 5mx1mx1m made from local Refractory • Heat Exchanger Imported(1m3, 100kg) • Uses Steam from Nuclear Reactor for Controlled Heating

  13. Material Transport • Need Glass, Steel, and Al transported from Refining to Manufacturing Airlock • Need Steel Rolls transported to Annealing Oven • Need Finished Products transported from Manufacturing Airlock to Area of Use • Rover or Automated Robot Carrier could easily be programmed to perform this function.

  14. Products Processing (Indoors) • Sheet Metal • Foil Foil Mill (8m2,1000kg) • Ducting 4m brake(4m2, 200kg), Resistance Welder(.25m2,50kg), Rivets • Piping/Tubing Tube Mill(4m2,500kg) • Wire/Cable Stripper(4m2,200kg), Wire Mill(6m2, 500kg) • Mesh Expander(3m2,200kg) • Stamped • Housings Press and Dies(4m2, 200kg), Castings(.5m2, 50kg) • Structural Members Press and Dies(4m2,200kg), Castings(4m2,100kg) • Rover Wheels Castings(.5m2,50kg), Press and Dies(4m2, 200kg) • Roll Winder/Unwinder (4m2, 400kg) • Cast Metal • Structural Beams Direct Chilled, Castings(4m2, 100kg) • Castings Castings(1m2, 100kg) • Valves • Sprinklers • Rover Parts • Glass Glass Cutter(2mx1m, 100kg) • Coatings • Zinc Galvanizing Use Locally Made PE Tank, and Zinc • Powder Coating Line Includes Oven, 3mx3m, 400kg • Electroplating Use Locally Made PE Tank, and appropriate Eplating solution • Shop • One Off Manufacture Drill Press, CNC Lathe, CNC Milling Machine (H&V), Grinders, Cutters • Prototyping Rapid Prototyping System, Wax or Plastic Investments Minimum • Robots/Automation • 6 DOF Motoman Handles Resistance Welder, Plasma Cutter, and Manipulator • Crane Loading and Unloading of Heavy Items

  15. Import Listing

  16. Slitter • May be used for making wire ribbon as well.

  17. Cutting device • Diamond Saw • Cuts both steel and glass

  18. Tubing Mill-Formers • Rolls strips into a tube and welds. • Tubing out can be rolled or cut in lengths.

  19. Coiler/DeCoiler • Roll and Unrolls Tubing, Strip, Wire, and Cable. • 200kgs per unit • ~1mx2m floorspace

  20. Steel Mill Control Room • For Context • Supervision of Process • Video • Instruments • Visual • Programming of new process

  21. Powder Coat Oven • Finished Products • Durable Epoxy Coating • Can be used on Steel and Aluminum

More Related