1 / 15

Math 20-1 Chapter 2 Trigonometry

Math 20-1 Chapter 2 Trigonometry. Teacher Notes. 2.1 A Angles in Standard Position. Terminal Arm. Initial Arm. Vertex. Math 20-1 Chapter 1 Sequences and Series. 2.1A Angles in Standard Position.

tamah
Download Presentation

Math 20-1 Chapter 2 Trigonometry

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Math 20-1 Chapter 2 Trigonometry Teacher Notes 2.1 A Angles in Standard Position

  2. Terminal Arm Initial Arm Vertex Math 20-1 Chapter 1 Sequences and Series 2.1A Angles in Standard Position In geometry, an angle is formed by two rays with a common endpoint. In trigonometry, angles may be interpreted as rotations of a ray. 2.1.1

  3. Angles in Standard Position No Examples Yes Examples Where would these go? No Yes No How would you describe an angle in standard position? 2.1.2

  4. Angles in Standard Position An angle  is said to be in standard position if its vertex is at the origin of a rectangular coordinate system and its initial arm coincides with the positive x-axis. The rotation of angle  is measured in degrees. y Terminal arm x Vertex Initial arm 2.1.3

  5. Sketch each angle in standard position. State the quadrant in which the terminal arm lies. 50° 170° 300° 200° 2.1.4

  6. Investigating Angles in Standard Position Create a 30°-60°-90° Triangle 1. Begin with an 8 1/2 × 11 sheet of paper. Fold the paper in half lengthwise and make a crease down the middle. 2. Unfold the paper. In Figure 1, the corners are labelled A, B, C, and D. a) Take corner C to the centre fold line and make a crease, DE. See Figure 2. b) Fold corner B so that BE lies on the edge of segment DE. The fold will be along line segment CE. Fold the overlap (the grey-shaded region) under to complete the equilateral triangle (DEF). See Figure 3. 3. For this activity, assume that the equilateral triangle has side lengths of 2 units. a) To obtain a 30°-60°-90° triangle, fold the triangle in half, as shown. b) Label the angles in the triangle as 30°, 60°,and 90°. 2.1.5

  7. Reflections of Reference Angles 300 300 300 1500 Angle in Standard Position_______ Angle in Standard Position_______ 300 300 2100 3300 Angle in Standard Position_______ Angle in Standard Position_______ 2.1.6

  8. Reflections of Reference Angles 600 600 1200 600 Angle in Standard Position _______ Angle in Standard Position _______ 600 600 2400 3000 Angle in Standard Position _______ Angle in Standard Position _______ 2.1.7

  9. Reference Angles [Cont’d] Angle in Standard Position _______ Angle in Standard Position _______ Angle in Standard Position _______ Angle in Standard Position _______ 2.1.8

  10. Sketching Angles in Standard Position Sketch the following angles in standard position. State the size of the reference angle. In which quadrant does the terminal arm lie? a) 1500 b)2900 c)2150 II Quadrant Quadrant IV Quadrant III 350 Reference Angle 300 Reference Angle 700 Reference Angle 2.1.9

  11. Drawing Angles in Standard Position Given a Point on the Terminal Arm Draw an angle, , in standard position such that the point P(-4, 3) lies on the terminal arm of an angle q. P(-4, 3) 3 q ref -4 2.1.10

  12. Drawing Angles in Standard Position Given a Point on the Terminal Arm Suppose the point P(-4, 3) was reflected in the y-axis. What the coordinates of the image point? What is the measure of the reference angle? P(-4, 3) q 370 Q(4, 3) 370 2.1.11

  13. Drawing Angles in Standard Position Given a Point on the Terminal Arm Suppose the point P(-4, 3) was reflected in the y-axis. What the coordinates of the image point? What is the measure of the reference angle? P(-4, 3) q 370 370 R(-4, -3) 2.1.12

  14. Drawing Angles in Standard Position Given a Point on the Terminal Arm Suppose the point P(-4, 3) was reflected in the x-axis and y-axis. What the coordinates of the image point? What is the measure of the reference angle? P(-4, 3) q 370 370 S(4, -3) 2.1.10

  15. Assignment Suggested Questions Page 83: 1, 2, 3a,b,c, 4c, 5a,b, 7b,c, 10a, 14, 15, 2.1.11

More Related