1 / 8

Open Midplane Dipole (OMD) Design for Dipole First Layout

US LHC Accelerator Research Program. bnl - fnal- lbnl - slac. Open Midplane Dipole (OMD) Design for Dipole First Layout. R. Gupta (BNL), N. Mokhov (FANL). Open Midplane Dipole for LHC Luminosity Upgrade Basic Design Features and Advantages. High luminosity (10 35 ) IR ~ 9 kW of beam power

simone
Download Presentation

Open Midplane Dipole (OMD) Design for Dipole First Layout

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. US LHC Accelerator Research Program bnl - fnal- lbnl - slac Open Midplane Dipole (OMD) Designfor Dipole First Layout R. Gupta (BNL), N. Mokhov (FANL)

  2. Open Midplane Dipole for LHC Luminosity UpgradeBasic Design Features and Advantages • High luminosity (1035) IR ~ 9 kW of beam power • Designing a magnet for large heat and radiation • Extraction of heat (cost – infrastructure + operating) • The particle spray from IP deposits most of its energy in a warm absorber for OMD, whereas in the conventional design it is deposited in coils and other cold structures. • Dipole first calc. show that OMD can tolerate ~ 9kW/side, whereas conventional designs would lead to large reduction in quench field. • The requirements for increase in CERN cryogenic infrastructure and in annual operating cost would be minimum for OMD, whereas in conventional designs it will be enormous.

  3. OMD Design Challenges • Counteracting large vertical forces between the coils without any structure appears to be a challenge. • Good field quality maybe a challenging task due to large midplane gap. • Large Bpeak/Bcenterratio in magnets with large midplane gap may reduce operating field. The optimum design may look totally different.

  4. A True Open Midplane Design In earlier “OMD designs”, absorbers were placed between the the coils. Secondary showers from the absorberdeposited a large amount of radiation and heat load on the coils. This problem is fixed in the new design.

  5. A Design with Simple Pancake Coils The design is based on two simple double pancake coils in each half of the magnet. • Mech. structure to make the coil as close to midplane as possible with adequate space for transmission of • beam in good field region • spray particles to warm region. Vertical Lorentz force on lower double pancake is upward. Space between upper and lower double pancake is just adequate to contain downward Lorentz forces. • Grading is done through varying current density (power supply) rather than through varying conductor (a more cost effective and more flexible approach for R&D magnets). The model above has three current densities: 350, 550, 700 A/mm2.

  6. Area where field error is <10-4 Field Harmonics and Relative Field Errors In An Optimized Design (Beam @ x=+/- 36 mm at far end) (Max. radial beam size: 23 mm) Geometric Field Harmonics: 40 mm is ½ of horizontal coil spacing • Field errors should be minimized for actual beam trajectory & beam size. • Optimization programs are being modified to include various scenarios. • Feedback needed from Beam Physicists on how best to optimize. • However, the design as such looks good and should be adequate.

  7. Field Uniformity in An Optimized 15 T Open Midplane Dipole Design Proof that good field quality can be obtained in such a wide open midplane dipole design (~1/2 of vertical and ~1/3 of horizontal aperture): The maximum horizontal displacement of the beam at the far end of IP is +/- 36 mm. The actual field errors in these magnets will now be determined by construction, persistent currents, etc.

  8. Design Iterations for Open Midplane Dipole During the course of this study, the following designs were examined: Next design to be examined : 8 T open midplane design (Nb-Ti?)

More Related