1 / 16

Low-losses e-Starter for compressors

Low-losses e-Starter for compressors. December 2007. CONTENTS. X0205 (back side). Board objective e-STARTER from ST New principle Breadboard schematics Explanation Breadboard performances Power consumption Immunnity Reliability & RoHS compliance Advantages / Drawbacks. ACST6-7ST.

senwe
Download Presentation

Low-losses e-Starter for compressors

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Low-losses e-Starter for compressors December 2007

  2. CONTENTS X0205 (back side) • Board objective • e-STARTER from ST • New principle • Breadboard schematics • Explanation • Breadboard performances • Power consumption • Immunnity • Reliability & RoHS compliance • Advantages / Drawbacks ACST6-7ST

  3. PTC Klixon Klixon LINE LINE PTC PTC RUN RUN START START Board objective Compressor LINE Klixon • Single phase compressor • Frige & freezer applications • Starters solutions: • Automatic turn-off relay • Expensive, poor reliability • Positive Coefficient Temperature Resistor (PTC) • High leakage current to keep the PTC hot, in high impedance mode • High power losses in OFF state • New solution for low-losses starter Vac START RUN Thermostat STARTER

  4. New principle Today PTC behavior versus mains voltage & compressor state IPTC (10A/div) IPTC (10A/div) VPTC (100V/div) VPTC (100V/div) Compressor OFF time < 1’ Mains: 264V RMS / Start capacitor Compressor OFF time > 10’ Mains: 198V RMS PTC voltage level increase is representative of long-enough start winding conduction

  5. Klixon Compressor Klixon Vac Vac PTC Control PTC Control T T Thermostat e-STARTER Thermostat New principle Connection diagram, with or without capacitor No capacitor Start or Run capacitor

  6. IA VAK VC2 VC1 Latch-up Level detection New principle ST solution to turn-off the start winding once the voltage across the PTC is high enough ZVS circuit

  7. New principle Explanation (1/2) • As soon as the mains voltage is applied: • T2 is on, thanks to the gate current provided by R2 • So T1 is turned on thanks to the gate current provided by T2 • At each Zero current crossing, the reapplied voltage across T1/T2 trigger back T1. • Both T1 and the PTC are then ON IA (5A/div) VAK (20V/div) PTC 1st step: T1 conduction

  8. New principle Explanation (2/2) • When the PTC conduction time lasted enough to start the compressor, its voltage suddenly rises • This voltage rises is sensed by R3/R4 divisor bridge. • If the level is higher than Dz level, the Thyristor achieved by Q1 and Q2 is latched • M1 is then turned on • As M1 is ON, there is no more gate current to trigger T2 • So T1 stays OFF • The PTC is also turned off. • No more current circulates through the PTC, so no power is dissipated by it. VC1 VC2 IA (5A/div) VC1 (10V/div) VC2 (10V/div) 2nd step: T1 turn-off

  9. Breadboard performances Stand-by power consumption IPTC (50mA/div) VPTC (100V/div) • Today PTC: • Current leakage to keep the PTC OFF ~ 30 mA • PTC losses at OFF state ~ 2 - 2.5 W • E-STARTER OFF state losses: • Assumptions: max line RMS voltage = 230 V • RMS voltage across e-STARTER = 350 V (with RUN cap.) • R2 + R3 power losses = 240 mW • Only 40mW typically for a 115V RMS application PPTC (5W/div) Stand-by losses divided by 10 ! (and also 0.6 to 1.5W saved on auxiliary winding !)

  10. Thermostat Klixon e-STARTER PTC ON OFF Delay Similar to PTC behavior Breadboard performances e-STARTER ON/OFF cycle Klixon • ON time = time to heat-up the PTC • Max: 1 to 6s according to PTC behavior • OFF time = ON time of both the thermostat & the klixon • Delay to turn-on back the e-STARTER = time to cool-down the PTC • Approximately 5-20 s • From end of last start-up ! Vac e-STARTER Thermostat

  11. Breadboard performances ON state behavior • ON state losses: • ACST6 conduction losses ~ 6 W max • Assumptions: 7A max peak current, Tj = 125°C, Vto/Rd spec. • R3 power losses ~ 0.5 mW • Only 30V typ. peak across the PTC; half-cycle mode • Max current versus conduction time to keep Tj < 125°C:

  12. Breadboard performances IEC61000-4-4 tests results Test conditions: Spike frequency: 5kHz Burst duration: 15ms Burst frequency: 3Hz Test duration: 60s Compressor 230V-50Hz E-starter board IEC61000-4-4 fast transient voltages generator No spurious turn-on up to 2kV (no permanent failure up to 4.5 kV)

  13. e-STARTER reliability ACST6-7ST QualPack results • Operating life test • Test conditions • ACST6 in TO220-AB, no heatsink • 14.5 A DC during 0.1s(equivalent to 11A RMS during 1s) • Thermal stress: Tj increases from 25 °C to 95 °CRq: Tj increase = 35°C for 5A RMS during 3s • No failure on 30 devices after 450 Kcycles • « Stalled rotor » test • Test conditions • ACST6 in TO220-AB, no heatsink • 13 A DC during 2.6 s(equivalent to 11A RMS during 0.5s then 2A RMS during 2.5s) • Thermal stress: Tj increases from 25 °C to 155 °C • No failure on 20 devices after 10 Kcycles

  14. 4.5cm 3.5cm e-STARTER reliability e-STARTER safety • UL compliance • Flammability: all our resins are UL94V0 compliant • No insulated packages required here (UL1557 not applicable) • EN60730 standard • ACST diode mode / short-circuit failure: • No safety issue as the PTC will protect the motor windings from overheating • Control board short-circuit failure: • Use a copper track which will blow-up if the motor current goes through it(normal current for the control board < 1 mA) Klixon PTC Control T Thermostat

  15. RoHS compliance • RoHS compliance • All ST component are RoHS compliant • PB < 1000 ppm (lead finish, solder balls) • Other heavy metals banned by RoHS directive are not present in STM products (lead free => RoHS compliant) • Exception : RoHS directive do not ban the use of Lead (Pb) in Frit seal glass and in High Pb-content alloys ( > 85%Pb) • Chemical compounds: refer to « ST chemical book »

  16. Vac Klixon PTC C Control Thermostat Advantages / Drawbacks • Advantages: • Remove PTC losses:Control circuit losses 240 mW compared to 2.5W with today PTC • No EMI noise (ZVS operation) • No half-cycle conduction • Faster reaction time (in case of mains interrupt) • Less risk of stalled rotor during short mains interrupt • RUN capacitor overvoltage protection • Possible to use lower voltage capacitors (less expensive) • Drawbacks: • Added components • No ZVS at plug-in (not a problem)

More Related