1 / 30

Bluetooth 4.0: Low Energy

Bluetooth 4.0: Low Energy. Short range wireless application areas. Low Power. State = low bandwidth, low latency data. How much energy does traditional Bluetooth use?.

safford
Download Presentation

Bluetooth 4.0: Low Energy

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Bluetooth 4.0: Low Energy

  2. Short range wireless application areas Low Power State = low bandwidth, low latency data

  3. How much energy does traditional Bluetooth use? • Traditional Bluetooth is connection oriented. When a device is connected, a link is maintained, even if there is no data flowing. • Sniff modes allow devices to sleep, reducing power consumption to give months of battery life • Peak transmit current is typically around 25mA • Even though it has been independently shown to be lower power than other radio standards, it is still not low enough power for coin cells and energy harvesting applications

  4. What is Bluetooth Low Energy? • Bluetooth low energy is a NEW, open, short range radio technology • Blank sheet of paper design • Different to Bluetooth classic (BR/EDR) • Optimized for ultra low power • Enable coin cell battery use cases • < 20mA peak current • < 5 uA average current

  5. Basic Concepts of Bluetooth 4.0 • Everything is optimized for lowest power consumption • Short packets reduce TX peak current • Short packets reduce RX time • Less RF channels to improve discovery and connection time • Simple state machine • Single protocol • Etc.

  6. Bluetooth low energy factsheet

  7. Bluetooth low energy factsheet #2 • Data Throughput • For Bluetooth low energy, data throughput is not a meaningful parameter. It does not support streaming. • It has a data rate of 1Mbps, but is not optimized for file transfer. • It is designed for sending small chunks of data (exposing state)

  8. Designed for exposing state • It’s good at small, discrete data transfers. • Data can triggered by local events. • Data can be read at any time by a client. • Interface model is very simple (GATT) 23.2˚C 60.5 km/h 12:23 pm Gate 10 BOARDING 3.2 kWh PLAY >> Network Available

  9. Bluetooth Low Energy Architecture

  10. Device Modes • Dual Mode • Bluetooth BR/EDR and LE • Used anywhere that BR/EDRis used today • Single Mode • Implements only Bluetooth low energy • Will be used innew devices / applications

  11. Device Modes • Dual mode + single modes BR/EDR stack Dual-mode stack Single-mode stack

  12. Physical Layer • 2.4 GHz ISM band • 1Mbps GFSK • Larger modulation index than Bluetooth BR (which means better range) • 40 Channels on 2 MHz spacing

  13. Physical Channels • Two types of channels

  14. Physical Channels • Advertising channels avoid 802.11

  15. Link Layer • Link Layer state machine

  16. Advertising • Devices can advertise for a variety of reasons: • To broadcast promiscuously • To transmit signed data to a previously bonded device • To advertise their presence to a device wanting to connect • To reconnect asynchronously due to a local event

  17. Data transactions • Once a connection is made: • Master informs slave of hopping sequence and when to wake • All subsequent transactions are performed in the 37 data channels • Transactions can be encrypted • Both devices can go into deep sleep between transactions

  18. Link Layer Connection • Very low latency connection

  19. Time From Disconnected to Data ~ 3ms

  20. How low can the energy get? • From the previous slide, calculate energy per transaction • Assume an upper bound of 3ms per minimal transaction • Estimated TX power is 15mW (mostly TX power amp for 65nm chips) • For 1.5v battery, this is 10mA. 0.015W * 0.003 sec = 45 micro Joule • How long could a sensor last on a battery? • An example battery: Lenmar WC357, 1.55v, 180mAh, $2-5 • 180mAh/10mA = 18Hr = 64,800 seconds = 21.6M transactions • Suppose this sensor sends a report every minute = 1440/day • For just the BT LE transactions, this is 15,000 days, or > 40 years • This far exceeds the life of the battery and/or the product • This means that battery will cost more than the electronics • This sensor could run on scavenged power, e.g. ambient light

  21. Competitive perspective

  22. Basic topology of 802.15.4

  23. ZigBee: Cluster tree network

  24. ZigBee PRO: mesh

  25. Future ZigBee: RF4CE • Targeted at Remote Control • Uses three channels only – 15,20 and 25

  26. Future ZigBee: 6LoWPAN • An initiative to “squeeze” IPv6 addressing into reasonably sized wireless packets • Being adopted for ZigBee’s Smart Energy Profile 2.0

  27. ZigBee and Bluetooth Low Energy • Business comparison: • ZigBee is older. It has gone through some iterations • ZigBee has market mindshare, but not a lot of shipments yet. • Market barriers: connectivity – ZigBee is not in PCs or mobile phones yet. • Technical comparison: • Zigbee is low power; Bluetooth LE is even lower. Detailed analysis depends on specific applications and design detail, no to mention chip geometry. • ZigBee stack is light; the Bluetooth LE/GATT stack is even simpler • Going forward: • ZigBee has a lead on developing applications and presence • Bluetooth low energy has improved technology, and a commanding presence in several existing markets: mobile phones, automobiles, consumer electronics, PC industry • Replacing “classic Bluetooth ” with “dual mode” devices will bootstrap this market quickly

  28. What are the USE CASES planned for BT 4.0? • Proximity • Time • Emergency • Network availability • Personal User Interface • Simple remote control • Browse over Bluetooth • Temperature Sensor • Humidity Sensor • HVAC • Generic I/O (automation) • Battery status • Heart rate monitor • Physical activity monitor • Blood glucose monitor • Cycling sensors • Pulse Oximeter • Body thermometer

  29. Example use: proximity • It can enable proximity detection • I’m in the car • I’m in the office • I’m in the meeting room • I’m in the movie theater • It can enable presence detection • Turn the lights on when I walk around the house • Automatically locks the door when I leave home • Turn the alarm off if I’m already awake

  30. Everyday objects can become sensors My pulse is … My blood glucose is … My temperature is … … and monitor things unobtrusively

More Related