1 / 19

Welding Power Point

Welding Power Point . Halton Auto Mike Tew. Oxygen . Regulator Pressure 20PSI- 35PSI Tall Green Tanks Power behind the flame High Pressure Tank volume 2500PSI. Acetylene . Regulator Pressure 4-5 PSI Tanks must stay standing up. If lose of acetone, pressures can become unstable

saeran
Download Presentation

Welding Power Point

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Welding Power Point Halton Auto Mike Tew

  2. Oxygen • Regulator Pressure 20PSI- 35PSI • Tall Green Tanks • Power behind the flame • High Pressure • Tank volume 2500PSI

  3. Acetylene • Regulator Pressure 4-5 PSI • Tanks must stay standing up. If lose of acetone, pressures can become unstable • Red small tank • Lighting fuel • Low pressure • Tank volume 250PSI • 21 PSI is when it Becomes the danger zone

  4. Safety First

  5. Dangers

  6. Changing tips • Welding tip • Demo • Cutting tip • Demo • Never tighten tip on with a wrench • Hand tight • No oil, grease or lube • Cutting tip handle (tip nut) must be tightened with wrench • Flash backs at handles not at tanks (will not allow flash back to destroy lines)

  7. Cutting and Welding

  8. Checking for leaks • Order the proper torch solvent to check for leaks • Never use soap and water • Soap contains oils and can make the tanks dangerous • Turn thanks on (handles off) prime lines • Close tank valves (leave lines primed for 20-45 mins) • If regulator pressures drops you have a leak • Spray and check for bubbles

  9. Lighting and shut down • A before O or up you can go • When the torches are shut down like this you reduce the chance of having the high pressure gas rush back on the low pressure gas creating an unstable mixture • Demo

  10. Neutral Flame • 5000 plus degree (neutral flame) • Metal melts at 2500 degree • Kindeling temp 1400 degree (ignition temp)

  11. Cutting • To properly cut the material needs Iron • Cutting is really Oxidizing • Keep tips clean • Dangers • Oxy (high pressure gas) has the possibility to push back up the Acet (low pressure gas) making it become unstable. • Don’t rest tip on material when cutting • Hissing sound is bad (to hot oxidizing flame)

  12. Brazing • A-O • Equal pressures 7 Acet – 7 Oxy (neutral flame) • Light Acet, till smoke crisps • Add Oxy • Flame temp 5000 plus degree • Perg lines every time

  13. Mig

  14. Welding Basic Set ups • Weld by sound (bacon and eggs) • Too little Amps gun will pop • Too much volts gun will burn wire in tip • Too find the proper relationship start with AMPS HIGH and bring it down to a proper buzz • Tip 45 Degree 4mm of material • Never perg you mig gas (leave in line, so moisture can not rust inside liner)

  15. Polarity • Flow of current • - to + Straight line (DCSP) • + to – Reverse line (DCRP) • Know what % is in your hand • Mig 70% + to – (DCRP) • Tig the ground (materile) melts (DCSP) • Toungston is in hand (-) 30% • Stick + to - (hand melts) • AC machines are junk

  16. DCSP

  17. Mig DCRP

  18. TIG

More Related