1 / 29

FAA Airport Design

FAA Airport Design. David Aarsvold Drew Hauck Elpiniqi Martopullo Tyler Watson 12-14-2006. Outline. Problem statement Functional requirements Constraints and limitations Alternatives Sensors Lights Interface Definition of project completion Positions and Responsibilities

Download Presentation

FAA Airport Design

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. FAA Airport Design David Aarsvold Drew Hauck Elpiniqi Martopullo Tyler Watson 12-14-2006

  2. Outline • Problem statement • Functional requirements • Constraints and limitations • Alternatives • Sensors • Lights • Interface • Definition of project completion • Positions and Responsibilities • Conclusions

  3. Problem • Runway Incursions • Poor visibility • Runways and Taxiways • Solutions • Hold short lines • Lights • Sensors • Better control from Tower

  4. Project Scope • The team is providing a complete design including the exact number, specification and location of all the lights and sensors. • The wiring system configuration that illustrates the connection of the visual aids to their power source and the interface with the control tower. • The final report will be submitted to the FAA by 12/21/2006.

  5. Background • Currently there are about 5.4 runway incursions for every one million operations. One of the FAA’s top priorities is to reduce the frequency of these incursions and the risk of runway collisions. • There are multiple ways to go about reducing runway incursions, including: • different lighting • new forms of guidance for the pilots • warning systems

  6. Functional Requirements • Improve communication between the control tower and the pilots/drivers on the runway • Enhance the visibility of the runway lighting system for the pilots/drivers • Make the communication system in tower less weather dependent through redundancy

  7. Project manager: David Aarsvold Coordinate communication with Duluth Airport and FAA point of contact Human Machine Interface Design Create cost estimate Industrial Engineer: Elpiniqi Martopullo ALMCS logic design Human Machine Interface SOP BRITE system application Mechanical Engineer: Tyler Watson Product and alternatives research Find correct spacing for lights Lighting control system Mechanical Engineer: Drew Hauck Product and alternatives research Find correct spacing distances for sensors Magneto sensor testing research Project Organization

  8. Lighting Alternatives • In pavement multi-color lens lights. • Pros: • Ease of installation and implementation. • Cheapest while still providing improvement over the current situation. • Cons: • Visibility angle of in-pavement lights. • Runway guard lights with in-pavement yellow lens lights. • Pros: • Greater visibility for pilots. • Similar to street lights • Cons: • Not accustomed to a stop light type of fixture. • Runway guard lights flashing yellow, in-pavement yellow lights and a red stop bar light. • Pros: • Most redundant of the options. • System that is currently used at airports. • Cons: • Uses more equipment than necessary.

  9. Reasons for Choosing Alternative • The green and red lens RGL and in-pavement light combination was chosen because: • The ability to let the pilots know at all times where to be and what they should be doing by adding visual confirmation. • The amount of redundancy and the placement of lights all complied with the FAA regulations in Circular 150/5340-30B . • Saves approximately $500,000 over the typical SMGCS system that is used currently in some airports across the country.

  10. Products • Inset Stop Bar/Runway Guard Light • Crouse-Hinds L-852G/S Model • Yellow lens cover on left side and blank on right, with quartz halogen bulbs. • Elevated Runway Guard Light • Siemens L-804 Model • Red and green lens covers for stop and go conditions.

  11. Location of Fixtures

  12. Special Condition Areas • The Duluth Airport has a few special conditions that needed to be addressed when specifying lighting locations. • Air Force Taxiways • Wider than the other taxiways. • ILS Situations • Hold short line is back farther from runway than usual.

  13. For the installation of the in-pavement lighting Sawed wireway that runs parallel to the lighting fixtures and run-offs connecting to each fixture. The parallel wireway cut needs to be 5/8” wide. The run-offs to the light fixtures have to be 3/8” wide. Need to allow for pavement sealer to be applied. Installation for Fixtures

  14. Installation Cont’d.

  15. Lighting Control System • For controlling the lighting system from the tower remotely the Siemens BRITE system was used. • BRITE Remote Control • 2 needed at each hold short line. • BRITE Master Unit • 1 needed for each CCR in the system.

  16. Information Flow for Lighting Information Flow to and from the RGL’s, Sensors, and the Tower.

  17. Functionality of Elements • BRITE Lighting Control System (LCS)  Central unit that links the tower to the field elements. • 2 Inputs: One from Remotes, one from IM • 3 Outputs: One to Remotes, one to IM, one to Tower • BRITE Master  Links Remotes to LCS • BRITE Remotes • 2 Inputs: Information from the tower PC via the LCS and Master regarding light color change • 2 Outputs: Connected to the RGL’s for color change

  18. Element Functionality cont. • Interface Module (IM) • 1 Input: Connected to the magneto reflexive sensors to detect presence of vehicle • 1 Output: Transmits the detection of a vehicle to the tower PC via the LCS • Default signal is interrupted when a vehicle is detected • Fail-safe system • Tower PC • 1 Input: Vehicle detection signal (from IM) • 1 Output: Lights change to green or stay red (to Remotes)

  19. Logic Flow

  20. RWY/TWY • Main view of airport • Control of all lights • Task Display is Intended to Support • Decision making • Control • Operator Capabilities • Perception • Attention • Memory Touch Screen Animation

  21. Zoomed in View • Features • Allow Take Off • Blue to match where vehicle is waiting • Disable Alarm • Yellow to match where the vehicle is traveling from

  22. HMI Display • Perceptual Advantages • Legible • Expectancies influence perception • Redundancy • Mental models • Realism • What is to be expected

  23. HMI Display • Attention • Minimized information • Proximity • Memory • Consistency

  24. Budget • Types of costs • Individual to each hold sort line • Sensors • Lights • Cable • Common to all hold short lines • ALCMS • BRITE system • Military accommodations • Excess lights

  25. Recommendations

  26. References • FAA Circulars: • 150/5340-30B • 150/5345-56 • 120-57A • Websites: • Siemens Airfield Solutions • Cooper Crouse-Hinds

  27. Acknowledgements • Darren Christopher of RS&H • David Keranen and William Pedersen • Chris Dixon and Rebecca Grammse

More Related