1 / 10

ALICE Magnets

ALICE Magnets. Ben Shepherd MaRS Group ASTeC STFC Daresbury Laboratory. Overview. Magnet settings table Calibration / field maps for energy measurements Degaussing Controls Online field measurements. ALICE Magnets.

pravat
Download Presentation

ALICE Magnets

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ALICE Magnets Ben Shepherd MaRS Group ASTeC STFC Daresbury Laboratory

  2. Overview • Magnet settings table • Calibration / field maps for energy measurements • Degaussing • Controls • Online field measurements

  3. ALICE Magnets • 66 magnets – a combination of new magnets (Danfysik) and some donated by Jefferson Lab + air core magnets (solenoids, correctors) QA QA QA QA DA DA QA QA DA QA QA QD DD QD DD QD S QD QD QD QD S QE QD QD QE QE QD QD DD DD QD QD QD QD S S DD DD

  4. Magnet Table • Hall probe and integrating coil tests have been carried out on all the new magnets • Field map produced for one of each type of the JLab magnets • Results summarised in a table relating model magnet strengths to required currents • http://projects.astec.ac.uk/ERLPManual/index.php/Magnet_table

  5. Magnetic hysteresis • At the low fields used in these magnets, hysteresis can have an effect • The field produced by a magnet will be slightly different depending on whether the current is being increased or decreased field current • e.g. for INJ-MAG-DIP-01 (field directly measured): • typical difference is about 8G (1% of nominal field) • 0.3° change in angle: 7mm at the OTR screen • The PSUs in use do not have the capability to bring the magnets to saturation • For a reproducible field: • Always increase the current • If you need to reduce it, take it back to zero first • A simple tool will be written to encapsulate this procedure • Worst case is probably the JLab quadrupoles

  6. Online field measurements • Three dipoles are important for energy measurements: • INJ-MAG-DIP-01 (first after booster) • AR1-MAG-DIP-01 (first after main linac) • ST1-MAG-DIP-01 (dump dipole) • A Hall probe is attached to the pole of each of these • Calibration has been carried out with respect to central field • This provides a check on the field • Should result in more accurate energy measurements

  7. Energy measurements (1) • INJ-MAG-DIP-01 • Used for measuring energy after the booster • We have a complete field map of this magnet • Take measurements of: • Initial angle and position (from YAG-03 and BPM-03 or YAG-02) • Central field (pole-mounted Hall probe) • Final angle (from YAG-03 and -04)

  8. Energy measurements (2) • AR1-MAG-DIP-01 • Measure energy after the main linac • For this magnet, we have integral fields along the nominal beam path and central fields • To measure energy: • Ensure the beam is going through the centre of ST1-OTR-04 andAR1-OTR-01 • Measure the field (pole-mounted Hall probe)

  9. Energy measurements (3) • ST1-MAG-DIP-01 • Measure energy post-deceleration • Two beams go through this dipole • When dumping the decelerated beam: • DON’T change the dump dipole current! • Record the field (pole-mounted Hall probe) • Record the position on DMP-OTR-01

  10. Magnet Controls • Control panel on the control room Linux consoles • Main Menu  Commissioning  Magnets • Magnet controls for the entire machine

More Related