1 / 38

APPLICATION & OPERATION OF TOTAL STATION OVERSEAS MARKETING CORPORATION (PVT),LTD

WELL COME TO TRAINING PROGRAME On. APPLICATION & OPERATION OF TOTAL STATION OVERSEAS MARKETING CORPORATION (PVT),LTD Association with Local Government Engineering Department ( LGED). Training Summery. What is Total Station? Total Station Overview Basic Concept Series Features

pilis
Download Presentation

APPLICATION & OPERATION OF TOTAL STATION OVERSEAS MARKETING CORPORATION (PVT),LTD

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. WELL COME TO TRAINING PROGRAME On APPLICATION & OPERATION OF TOTAL STATION OVERSEAS MARKETING CORPORATION (PVT),LTD Association with Local Government Engineering Department ( LGED)

  2. Training Summery • What is Total Station? • Total Station Overview • Basic Concept • Series Features • Application Software • Operation/Application

  3. INTRODUCTION - TOTAL STATION Total Station is an electronic device, which can determine the coordinate of a target point in a digital form. It transmits beam of infrared light towards the target (reflector) & receive the reflected beam from the prism & calculate the distance, bearing & 3D coordinate of that target point with respect to the reference point.

  4. Traditional Survey Equipment & Total Station • Distance & Level • Bearing / Angle • Co-Ordinate (GPS)

  5. SECUANTIOL STAGE OF TOTAL STATION

  6. Main Technical Data “Ultimate Standard” • Highest Protection against Dust and Water: IP66 • Consistence speed Meas. Time: 0.9sec • World-proven, Time-tested Angle Reading System: Absolute Encoder • Quick Operation in All Conditions: Easy-to-use control panel • Security: Password function • Flexible Data Management: SD/SDHC&USB slot Bluetooth class2 (option) • Built-in Laser Plummet (option)

  7. Parts of Total Station

  8. Parts of Total Station

  9. Input Parts of Total Station

  10. Soft Key Operation Select <S-O data> [ESC] key [ S-O] key [OK] key [OK] key

  11. Password Protection Function • Security purposes • 3 to 8 alphanumeric characters

  12. Application • Distance and Angle Measurement • Angle Measurement • Area Calculation • Remote Elevation Measurement (REM) • 3-D Coordinates Measurement • Resection • Set-out • Point Projection • Traverse Adjustment

  13. Surveying Work Flow • Tripod Setup On a Known Point • Instrument Setup on Tripod • Centering & Leveling the Instrument • Configuration (one time) • Job open (If required) • Backside Point Setup (Prism) • Start Measure • Data Transfer to PC

  14. Instrument Set up on The Station • Set the Tripod on the Known Point • Put the Instrument on Tripod & • Confirm Centering using by • Optical plummet • Confirm leveling by Horizontal & • Base Circular level • Set the prism on the Known Point • Power on the TS

  15. Instrument Configure

  16. JOB Open Data Transfer MEAS/---MEM/ CONFG (F3) MEAS/---MEM/ CONFG (F3) Job (Enter) Comms output (Enter) Selection (enter) Select (enter) Job Name Edit (enter) PC Work Coms setup) Enter Unit OK Surveying Work Flow

  17. Measure (P1) MEAS/---MEM/ CONFG (F1) Distance (F1) SHV(Slope, Horizontal, Vertical Distance) (F2) O SET(Horizontal angle) (F3) AIM (F4) FUNC for Page Change Surveying Work Flow

  18. Surveying Work Flow

  19. Target/ Prism Setting

  20. Application Angle Measurement The included angle between two points can be measured using ‘0SET’ function. • Sight to the first target • Press F3 for ‘0SET’ and it will flash. • Press F3 again while ‘0SET’ is flashing and horizontal angle display will set to 0º 00’ 00”. • Then sight to the second target and the horizontal angle display is the included angle between 2 points.

  21. Application Distance and Angle Measurement Distance and Angle can be measured at the same time using F1 (DIST).

  22. Area Calculation

  23. Remote Elevation Measurement (REM)

  24. Application Remote Elevation Measurement

  25. 3-D Coordinates Measurement

  26. Application Coordinate Measurement

  27. Resection

  28. Application Resection Measurement

  29. Set-out

  30. Application Setting-out Measurement

  31. Application Setting-out Line

  32. Point Projection

  33. Application Point Projection

  34. Application Traverse Adjustment

  35. Using External Memory Media Slide the catch on the external interface hatch cover down to open. Insert the memory device in the respective slot. The contact part of SD card should be facing the instrument. To remove SD card from slot, push further in first. Then release to eject.

  36. Using External Memory Media Selecting Media Type • Power on the instrument. • By default, the instrument will be in measurement page. • Press ‘ESC’ to get into status page. • Press ‘MEDIA’ to get into media mode. • Select ‘Media selection’ • Select desire media type from ‘SD’ or ‘USB’ using left/right arrow key • Then press ‘OK’

  37. Using External Memory Media Storing Job Data • Select ‘Save data’ in ‘Media’ • Select the job to be recorded and press ‘Enter’. ‘Out’ will be displayed to the right of the selected job • Then press ‘F4’ for ‘OK’ • Enter name for the job file (by default, job file name in the instrument will be assigned) • Then press ‘F4’ for ‘OK’ and the job file will be saved in the selected medium with entered file name.

  38. End of Presentation Thank You!

More Related