1 / 36

COMP1121 Computers and Computer Networks

COMP1121 Computers and Computer Networks. Richard Henson University of Worcester April 2008. Week 10 – The Physical Layer: Network Hardware. By the end of this session you should be able to: Identify and select network hardware devices for a variety of purposes

parchibald
Download Presentation

COMP1121 Computers and Computer Networks

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. COMP1121 Computers and Computer Networks Richard Henson University of Worcester April 2008

  2. Week 10 – The Physical Layer: Network Hardware • By the end of this session you should be able to: • Identify and select network hardware devices for a variety of purposes • Explain what a hardware driver is how plug-and-play works • Explain how to install a network card and ensure it provides network connectivity

  3. Transmission Media • “Connection” between computers on a network is essential for sending/receiving digital data • doesn’t need to be overtly physical • 0’s and 1’s can be transmitted without an apparent physical medium… • Suggestions?

  4. Hardware requirements: • A networking “subsystem” on each computer, which links in with the motherboard in some way • at one time this always happened via a network card connecting the motherboard via ISA or PCI connector • nowadays, the networking hardware is often built onto the motherboard • A plug/socket arrangement with the physical medium • USUALLY… this is a “telephone-type” arrangement to insulate twisted pair copper cable • known as RJ45 • AT ONE TIME… co-axial cables and connectors like a TV aerial system were used • known as BNC

  5. Network Cardsoftware requirements • Software interfaces effectively with level 3 protocol • nowadays usually IP • part of operating system networking component • requires allocation of IP address • Level 2 software converts packets into “frames” of data • Level 1 software converts the binary frames into electricity (high/low voltage) and sends them out onto the physical medium

  6. Network Cardsoftware requirements • Each card gets a unique identifier during manufacture • known as the MAC address – where “MAC” (media access control) is part of the data link layer • Provides software for physical signal/binary number interconversion • OSI layer 1 signals - converts to layer 2 frames • OSI layer 2 frames converted to layer 1 signals

  7. Binding Network Card Software to an operating system “protocol stack” • Two way process: • Down: Level 3 IP packets need to be converted to frames • Up: Level 2 frames need to be converted to IP-compatible packets • As with other hardware devices… • achieved through software called “drivers” • Plug-and-play hardware can tell the operating system what it is and provide the relevant software on network card ROM • otherwise, driver software will be needed…

  8. Transmission Media • From the network card/adaptor port, data can be physically transmitted in a number of ways: • via insulated copper cable • via optical fibre cable • via “wireless” media e.g. radio waves, microwaves, infra-red beams, etc. • Transmission medium type greatly affects the overall speed and resilience of the network and the number of packets that get corrupted

  9. Transmission Media - Cabling • Two types of cables have historically been used in LANs: • thin Coaxial – up to 200 metres per cable run • thick Coaxial – up to 500 metres per cable run • Most cabled networks nowadays use either: • Unshielded Twisted Pair (UTP) – up to 100 metres • Fibre-Optic – up to 1 km per cable run

  10. Transmission Media – Wireless • “Wireless” means transmission using electro-magnetic radiation • means an electro-magnetic wave vibrating with a specified frequency and moving forwards at the speed of light… • light itself is electromagnetic radiation • We take wireless for granted now, but it was first used to transmit and receive signals only about 100 years ago • theoretically shown to be possible by Maxwell, UK • invention usually attributed to Marconi, Italian

  11. Discovery of Electro-magnetic Radiation • Potential existence of radio waves were predicted in 1864 • an amazing piece of maths… • Started almost 30 years before Marconi with Cambridge professor James Clerk Maxwell • successfully predicted most of the physical laws about propagation and speed of radio waves • noted their resemblance to light waves • showed how they could be reflected, absorbed and focused like the beam from a torch • and could change the very nature of the object on which they were focused

  12. Putting Theory into Practice • Hardly anybody believed Maxwell in 1864! • BUT his theory was quantified by Oliver Heaviside into two equations • Over the next 30 years they became a physical reality • in 1879, Prof. David Hughes walked up Portland Place, London with a device that picked up transmitted radio waves • in 1887, German scientist Heinrich Hertz carried out a famous set of experiments that proved • that Maxwell had been right all along • that some materials reflected radio waves back… • in 1894, the British scientist Oliver Lodge transmitted wireless signals over 150 yards

  13. First Data Transmission by Radio waves • An Italian in London… • ref: http://www.connected-earth.com/Galleries/Telecommunicationsage/Awirelessworld/Theoriginsofradio/index.htm • Marconi arrived in 1895, 21 years old, with a new system of 'telegraphy without wires' • had already approached the Italian government - but it showed no interest. • 1896: • called upon the Engineer-in-Chief of the Post Office to demonstrate his system • allowed him to set up his transmitter on the roof of the Central Telegraph Office, and a receiver on the roof of a building 300 yards away. • On July 27 succeeded in sending morse code signals between the two locations - world's first recorded wireless message. By 1901, signals had crossed the Atlantic!

  14. What vibrates, in electro-magnetic waves? • Put simply: • electricity through a coil produces a magnetic effect • magnetism through a coil generates electricity • If the electricity is varied, or “pulsed”, the magnetic field will also pulse at the same rate • magnetism travels even through a vacuum • can be used to carry a signal • Maxwell’s brainwave was suggesting that this effect could be used to transmit signals without wires • need a energy source, & transmitter/receiver coils

  15. Transmission Media – Wireless • Data carried most efficiently nowadays on extremely high frequency radio waves: • patented as “radar”; now called microwaves • used in ww2 - bounced off enemy planes • http://www.fi.edu/weather/radar/video/ /historyrad.mov • Less bandwidth & lower reliability than optical fibre or cable, but becoming very popular… e.g. • Cellular Mobile Phone networks • Connecting mobile phones to each other & the Internet • Satellite microwave • Data to/from satellite in geocentric orbit (22300 miles up!)

  16. Transmission Media - Wireless • Point-point microwave • data transmitted either across roofs of adjacent campus buildings, or “line of sight” point-point across open land (up to 30 miles away) • Radio wave • Either “spread-spectrum” or “narrow-band” • Useful for connectingmobile laptops to a LAN

  17. Mechanism of data transfer • Coaxial or twisted pair: • data is transmitted by electrical conduction • cabling system consist of two (or groups of two) conducting wires • Fibre optic • Data transmitted by light internally reflected through a thin fibre-glass tube • Data can be safely transmitted separately in both directions

  18. Cabling and Crosstalk • Two parallel wires, as used in domestic electrical cabling, cannot be used for data • Reason - “crosstalk”: • electrical interference between signals in the two wires • signals jumping from one wire to the other • The longer the cable, the greater the chance of crosstalk • Therefore there will always be a limit on cable run between data storage devices

  19. Crosstalk and Coaxial Cabling • Magnetic fields produced by electricity in the two wires tends to cancel out • This greatly reduces, but does not eliminate cross talk • There is a recommended maximum length for Ethernet cables for this reason: • thin Ethernet - 185 metres • thick Ethernet - 500 metres

  20. Thin Coaxial Cable • Also known as: • Thin Ethernet • Base band • Cable consists of: • single copper central wire covered with a layer of insulation • itself covered by wire braiding (a patchwork made of very thin copper wire) • Whole arrangement wrapped in a (usually black) plastic tube

  21. Thin Coaxial Cable • Also known as IEEE 10base2 • IEEE - Institute of Electrical and Electronic Engineers (more on this erudite body later) • Not very flexible because of the nature of its construction • Available in a range of different qualities • Generally used for networks using a bus topology • Recommended maximum data transmission rate - 10Mbits/sec

  22. Connecting Thin Coaxial Cable • Computersconnected to a thin coaxialbus network need a network card with a BNC socket • Such network cards are becoming very rare… • The coaxial bus connects to the network card through a metal BNC “T connector” • The coaxial cable itself must be “terminated” at each end with a BNC “terminator” that completes the electrical circuit

  23. Thick Coaxial Cable • Also known as Thick Ethernet or broadband cable • very expensive and cumbersome to use… • Includes two shielding layers between the wires to allow for “harsh” environments (lots of electrical “noise” caused by nearby electric motors, etc.) • Superior to thin Ethernet is two ways: • Higher data transmission rates (100Mbits/sec recd maximum) • Larger cable lengths (500 metres recd. maximum)

  24. Twisted Pair Cable • The current standard in most LANs • Compared to coaxial: • cheaper • much more flexible • easy to use • doesn’t need BNC T connectors or terminators • Twisted Pair construction tends to cancel out magnetic fields - greatly reducing cross talk (but not as effectively as coaxial)

  25. Twisted Pairv Thin Coaxial - Disadvantages • Use of the “twisted pairs” - wrapping the individual wires around one another - does not reduce cross talk as effectively as coaxial cable • More susceptible to “ harsh” environments (especially rapidly changing magnetic fields) • Extra insulation of twisted pair cable recommended in such circumstances • Cable therefore becomes more expensive

  26. Topology - Twisted Pair Cable • Normal use - Star topology • Connections could go directly from network card sockets to hub ports • using RJ45 plastic end connectors • similar to RJ11 telephone line connectors (but not the same!) • In practice, for flexibility, a combination of CAT5 cables, connectors, patch leads/sockets used to connect network cardsto hubs • Most modern network cards are known as “combo” - this means they have sockets for both BNC (coaxial) and RJ45 (twisted pair)

  27. EIA/TIA Cabling Standards for Twisted Pair cable • EIA - Electronics Industries Association • TIA - Telecommunications Industries Association • EIA/TIA is a Cabling standards body • joint venturebetween the EIA & TIA • The EIA/TIA 568 standard covers five types of unshielded twisted pair cable known as (in increasing quality) CAT1 through to CAT5 • CAT5 standard has evolved to CAT5f

  28. Existing EIA/TIA 568 standards • CAT1 is OK for voice communications, but not suitable for digital data • CAT2 can only support digital data transfer rates of up to 4 Mbits/sec • CAT3 can only support digital data transfer rates of up to 10 Mbits/sec (this is the lowest standard for IEEE 802.3 10BaseT Ethernet networks - next week’s session) • CAT4 can only support digital data transfer rates of up to 16 Mbits/sec • CAT5 can officially handle up to 100 Mbits/sec, although it is being used on faster (e.g. 155Mbit/sec) FDDI networks • CAT6 can handle faster rates, theory up to 1 Gigabit

  29. Features of Twisted Pair Cable • Most popular type currently known as Category 5 UTP (unshielded twisted pair) • 5e still widely used • 5f, 6current preferred standards • CAT5e upwards can carry data at high transmission rates (up to 200 Mbits/sec) • CAT5f, CAT6: even higher (1 Gigabit/sec) • Because of the greater susceptibility of twistedpair to cross talk, the maximum recommended cable length for CAT5 is 100 metres

  30. Optical Fibre Cable - construction • The cable itself consists of: • a glass or plastic central light conductor • surrounded by a further layer of glass or plastic cladding • and a protective outer casing • The cable must be connected directly to: • light emitter (one end) • light detector (other end)

  31. Optical Fibre Cable • First of all, the electrical signal needs to be converted into light pulses. This done by: • either an LED (light emitting diode) • or a Laser • The light pulses are then directed into the central tube • The light is repeatedly totally internally reflected as it passes along the inside of the tube - as if it were on the inside of a mirror

  32. Optical Fibre Cable (continued) • Thanks to total internal reflection, a cable can carry light considerable distances, including round bends, without significant energy loss • 1 km cable run quite possible… • cable must be bent carefully, otherwise internal structure could be damaged… • On emerging from the cable, the pulse is converted back into an electrical signal by a photodiode • More detail: • http://www.arcelect.com/fibercable.htm

  33. Optical Fibre Cable - advantages • Speed of transmission (up to Gbits/sec) • Ability to support voice and digital data along the same cable • Security (very difficult to tap) and reliability of transmission (almost immune to electrical interference) • A pair of optical fibres can simultaneously carry light/data in each direction (full duplex) with no danger of signal attenuation • With copper cables, signals in adjacent cablescould interfere with each other

  34. Optical Fibre Cable - disadvantages • Expensive • Expensive to install • Not as flexible to use in tight areas of twisted pair • Needs expensive hardware to reliably convert light into electricity and vice versa

  35. Health, Safety & Transmission Media • Some people object to cable being visible • apart from aesthetic reasons, also a potential safety hazard • Different types of twisted pair cable are availablefor different environments (e.g. under carpets or in the plenum space above a “lowered” ceiling) • This usually increases the likelihood of crosstalk, and effectively reduces the recommended minimum cable length • Standards laid down by IBM in the 1980s…

  36. IBM Cabling Categories

More Related