1 / 23

STATUS REPORT ON VACUUM CHAMBERS (Dipole & Straight) & DIPOLE MAGNETS FOR TL-2 OF CTF3

STATUS REPORT ON VACUUM CHAMBERS (Dipole & Straight) & DIPOLE MAGNETS FOR TL-2 OF CTF3 A.K. JAIN, S.S. PRABHU, S. KOTAIAH RRCAT, INDORE (INDIA). Vacuum Chambers. Dipole Vacuum Chambers :.

padgettk
Download Presentation

STATUS REPORT ON VACUUM CHAMBERS (Dipole & Straight) & DIPOLE MAGNETS FOR TL-2 OF CTF3

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. STATUS REPORT ON VACUUM CHAMBERS (Dipole & Straight) & DIPOLE MAGNETS FOR TL-2 OF CTF3 A.K. JAIN, S.S. PRABHU,S. KOTAIAH RRCAT, INDORE (INDIA)

  2. Vacuum Chambers

  3. Dipole Vacuum Chambers : Initially, two test vacuum chambers fabricated in aluminum grade AA 6061 for qualifying machining & welding procedure. Surface finish < 0.30 microns achieved. Welding torch manuveres needed to access some portions of chamber. For third chamber, design was changed to simplify welding. Leak rate obtained ~3 x 10-10 Torr – ltr / sec.

  4. DIPOLE VACUUM CHAMBERS Machined & Welded Prototype Chamber Initial Trial Final Trial

  5. DIPOLE VACUUM CHAMBERS

  6. END FLANGES OF DIPOLE VACUUM CHAMBERS

  7. Dipole Vacuum Chambers (Contd…) Fabrication & Processing : Material: AA6061–T6 is silicon magnesium based aluminium alloy. (Material is solution heat treated and artificially aged). Tooling : High-speed cutters were used. Cutters equipped with peripheral mounting, high positive rake angle (340), coated carbide inserts with 900 approach angle. One of three inserts had a “wiper insert” to get good surface finish. Processing : Chemical cleaning-Approved by CERN for aluminium alloy grade AA6061-T6. After chemical cleaning, jobs were hand scrapped in the lip area to remove oxide layer just before welding.

  8. Dipole Vacuum Chambers (Contd…) TIG WELDING : Welders were qualified as per section IX of ASME code. Cleanliness and humidity level of the weld room was maintained using air conditioners, air curtains and Dehumidifiers. Base material used: AA 6061 –T6 ( containing Si- 0.6%, Mg – 1-1.2%, - Cu - 0.27%) Filler wire used: AWS A5.10 ER 4043 (Containing Si–5%, Mn –0.05% Fe – 0.4% Al – rest) Shielding gas used: XL grade argon 99.999% as per IS-5760-1983 (Grade - 1) (Impurities - Oxygen less than 1.5 ppm., Moisture less than 1.0 ppm, total hydrocarbon – NIL)

  9. Welding Parameters Peak current 60-70 Amps. Back ground current 25 Amps. Pulse frequency 7 Hz. (at high position) Pulse Ratio 80% Type of arc Hard Arc Shielding gas flow rate 8 Ltrs / min Relative Humidity Less than 35%

  10. Dipole Vacuum Chambers (Contd…) Present Status : Fabrication and welding procedures qualified. Raw material AA 6061 T6 procured. Awaiting CERN’s approval of TL-2 optics design & also magnet design. Final drawings for chamber fabrication to be taken up thereafter. Total nos. of dipole chambers ~5. Assembly of dipole chamber with bending magnet has been tried using CAD. There is no problem in the assembly.

  11. Straight Chambers : RRCAT, Indore will deliver these chambersbuilt out of extruded aluminum grade AA 6061 T6. This will avoid welding of chambers at the edges and their machining on a CNC vertical milling machine. Extrusion job already ordered. Extruded material expected at RRCAT ~April, 2007. Once TL-2 optics is frozen, material will be cut to required lengths, ends machined to suit the welding joints with end flanges.

  12. Straight Chambers

  13. DIPOLE MAGNETS FOR TL-2

  14. DIPOLE MAGNET Specifications 

  15. Dipole Magnets (Contd…) Magnet Core Material: 1.5 mm thick low carbon steel sheets supplied by M/s Cockrehill Sambre. B/H data and other information : Coercivity – 70 A/m  Carbon content < 0.01 %  Yield Strength 120 N/mm2  Tensile Strength 260 N/mm2  Thickness spread < 1.5 %

  16. Dipole Magnet Bottom Half Block Dipole Magnet Coil Pan Cake

  17. DIPOLE MAGNET ASSEMBLY Overall Mechanical Details of Assembled 35 Dipole Magnet Magnet height 640 mm Magnet Width 1000 mm (812 + 30 + 158) Magnet Length 910 mm Magnet total weight 2200 kg

  18. CORE BLOCK FOR DIPOLE MAGNET

  19. Fabrication Stages: • Laser Cutting of Stampings. • Stacking of stampings & pressing to form a block. • Welding of stampings to get block. • Machining of pole surface & other reference surfaces. • Assembly of two blocks along with water cooled coil pancakes.

  20. Dipole Magnets (Contd…) Present Status : Engineering drawings for 350 bending magnet completed; Sent to CERN, but approval awaited. Quantity required 2 nos. Fabrication will start only after CERN’s approval of drawing. Engg drawings for 17.50 bending magnet completed; will be shortly sent to CERN for approval. Quantity required 3 nos. Raw material for core & coil procured.

  21. THANK YOU FOR YOUR ATTENTION

More Related