Updated Concerns on the Material Interactions

1. Updated Concerns on the Material Interactions Dai-Kai Sze University of California, San Diego Presented at the ARIES Project Meeting September 3-5, 2003 Atlanta, Georgia

2. Material Interactions • The compatibility between the structural materials and coolant/breeding materials set key limitations on the allowable temperature. • The allowable corrosion rate is about 10 mg/m2-h. • The corrosion rate is strongly temperature dependent. • Relax of the corrosion rate will have only a small effect on the allowable temperature.

3. Corrosion Concerns • Literature review identified they are limited information on the results of corrosion studies. • Some of the experimental results do not support the conventional window. • Much more experimental works will be required to define the corrosion rates. • Some results for the Li/V, LiPb/SiC and flibe/FS will be discussed here.

4. Li/V compatibility • One of the key reasons to use the Li/V blanket is that Li is compatible with V-alloy to high temperature(600 to 700°C). • BCSS suggested that V is very compatible with Li. • Some existing data does not agree with this conclusion.

5. Results from ANL work • Dissolution rates of V in Li were measured for different type of V-alloys. • This experiment was done in a forced convection loop with Li circulating rate of about 1 liter/m. • The corrosion behavior was evaluated by measuring weight change. • The N concentration was between 20 to 100 WPPM. • Chopra and Smith, “Corrosion behavior of Vanadium Alloys in Flowing Lithium,” Journal of Nuclear Materials, 155-157 (1988).

6. Corrosion Rate of V-15Cr-5Ti • Reported corrosion rates: 482°C 427°C 4.97 mg/m2-hr 0.27 mg/m2-hr • The corrosion rate will be 0.1 cm/y at 600C, and 0.5 cm/y at 650C, by extrapolating from the low temperatures. ).

7. Other Results • Corrosion of V3Ti1Si by Li was measured by Adelhelm. • A pumped Li loop was used, with velocity of 7 cm/s. • The Li temperature was 806 to 823K. • The N concentration was 8 to 64 wppm. • The measured V corrosion rate was between 2 to 20 mg/m2-hr. • There was a minimum corrosion rate at XN = 30 ppm. Gh. Adelhelm, “Corrosion of V3Ti-1Si in flowing Lithium,” Fusion Technology,8, July 1985, P. 541.

8. Other Information • Some work from RF reported weight gain in V/Li corrosion experiments. • Those were from capsule tests with very high N concentration. • No data is available to suggest that the corrosion rate on V by Li is low at high temperature. • Chopra concluded “the dissolution rates of all vanadium alloys were greater than of ferritic steels (in his experiments).”

9. Question • What is the base to suggest that Li/V blanket can operate at 600 to 700°C?

10. LiPb/SiC Compatibility • It has been suggested that LiPb and SiC is compatible up to 800°C, and maybe higher. • Available experimental results do not support this suggestion. • Based on experimental results, it can not be concluded that if SiC is compatible, or not compatible, with LiPb at 800°C.

11. LiPb/SiC Experiment • The work was done in a rotating disk set up, with a rotational speed of 800 revolutions/m (1.67 m/s). • The temperature of the experiment was 800°C, and up to 3100h. • Both the coupons and the LiPb sample were investigated at the end of the experiements.

12. SiC Coupons • It was difficult to clean up LiPb from the SiC coupons. • Therefore, it was not possible to measure the weight variation of the SiC speciman after the test. • No information was obtained on either weight gain, or weight lost, during its contact with liquid LiPb.

13. LiPb Samples • The Si concentration in LiPb is about 12 wppm, both before and after the test. • The author suggested that no dissolution occurred during the test perhaps due to the low Si solubility in LiPb. • However, this also suggested that the Si is saturated in LiPb at a concentration of 12 wppm. • 12 wppm is a very high solubility. If we assume that the Si concentration in LiPb is always at a saturation level, (Which may not be), the removal rate of Si from SiC will be very high. • There is potential that the entire blanket structure can be removed in one day. • 12 wppm solubility is a cause for concern.

14. LiPb/SiC Compatibility • There is no data available to suggest if SiC is compatible to LiPb at 800°C, or not compatible. • ORNL recently did some SiC/LiPb compatibility test, at 1000°C and 800°C. • Air in leak ruined the 1000°C experiment. • ORNL is still investigating methods to remove LiPb from the SiC coupons.

15. REDOX Reaction • For MSBR, the following Redox reaction was used to control TF and F2 potential. UF3 + F ----- UF4 • A possible Redox reaction for fusion application is   Be + 2F ---- BeF2 • This redox reaction is being studied at INEL as a part of JUPITER-II collaboration.

16. Conclusion • There are only limited experimental results to assess the compatibility between many structural materials and coolant/breeding materials. • Careful review of those results raised questions on the temperature limits set for the systems. • More detailed assessments on the condition of the experiments, the results of the experiments, and the conclusions draw from those results is required.