1 / 10

ECE 447 Fall 2009

ECE 447 Fall 2009. Lecture 8: TI MSP430 Interrupts, ISRs. ECE447: Interrupt Service Routines in Assembly. PORT1_ISR: ; respond to inputs on port1 reti ; return from interrupt ORG 0FFE8 DW PORT1_ISR -- or -- COMMON INTVEC ORG PORT1_VECTOR DW PORT1_ISR.

nyla
Download Presentation

ECE 447 Fall 2009

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ECE 447 Fall 2009 Lecture 8: TI MSP430 Interrupts, ISRs

  2. ECE447: Interrupt Service Routines in Assembly PORT1_ISR: ; respond to inputs on port1 reti ; return from interrupt ORG 0FFE8 DW PORT1_ISR -- or -- COMMON INTVEC ORG PORT1_VECTOR DW PORT1_ISR • The service routine itself is quite simple. (Note the “reti” instruction.) • To store the address of this ISR in the proper vector table location an ORG directive is used. • PORT1_VECTOR is defined in the header file relative to the INTVEC segment. The COMMON directive must be used to place the defined address (PORT1_ISR) in the correct location. This is useful for defining ISRs in multiple files.

  3. ECE447: Interrupt Service Routines in C // tell the compiler the vector for this ISR #pragma vector = PORT1_VECTOR __interrupt void port1_isr(void) { // respond to inputs on port1 } • “#pragma vector” tells the compiler to store the address of this routine in the PORT1_VECTOR location. • “__interrupt” is used to tell the compiler that this function should end with a “reti” instruction.

  4. ECE447: Interrupt Vector Jump Table • The jump table tells the program where to go when an interrupt occurs. • A vector points to the address where the interrupt service routine starts. • The MSP430 jump table is stored in RAM from 0xFFC0 to 0xFFFF and can be modified by the programmer.

  5. ECE447: MSP430 Interrupts

  6. ECE447: MSP430 Status Register • GIE (bit 3): Global Interrupt Enable • 1: Enables all interrupts (interrupts must also be enabled individually) • 0: Disable all interrupts NOTE: SR is saved on the stack and cleared when an ISR is executed.

  7. ECE447: Setting and Clearing the General Interrupt Mask • Assembly EINT – Enable interrupts (set GIE) DINT – Disable interrupts (clear GIE) • C asm(“ EINT”); asm(“ DINT”); • C (#include intrinsics.h) __enable_interrupt(); __disable_interrupt();

  8. ECE447: MSP430 Interrupt execution flow RAM JUMP TABLE 0xFFFF SR PC 00F8 EE 10EE 10 0000 0xFFC0 STACK F8 00 SP RAM SERVICE ROUTINE 0x10EE

  9. Interrupts Example: Toggling LEDs // Listing 6.5: Toggles LEDs in ISR using interrupts from timer A CCR0 // in Up mode with a period of about 0.5s #define LED1 BIT3 #define LED2 BIT4 void main (void) { WDTCTL = WDTPW | WDTHOLD; // Stop watchdog timer P2OUT = ~LED1; // Preload LED1 on, LED2 off P2DIR = LED1 | LED2; // Set pins with LED1,2 to output TACCR0 = 49999; // Upper limit of count for TAR TACCTL0 = CCIE; // Enable interrupts on Compare 0 TACTL = MC_1 | ID_3 | TASSEL_2 | TACLR; // Set up and start Timer A // “Up to CCR0” mode, divide clock 8, clock SMCLK, clear timer __enable_interrupt ( ); // Enable interrupts (intrinsic) for (;;) { // Loop forever doing nothing } // Interrupts do the work } // Interrupt Service Routine for Timer A channel 0 #pragma vector = TIMERA0_VECTOR // Assoc. the funct. w/ an interrupt vector __interrupt void TA0_ISR (void) // name of the interrupt function (can be anything) { P2OUT ^= LED1 | LED2; // Toggle LEDs }

  10. ECE447: MSP430 Interrupt Class Exercise Write a program that collects samples from input Port 2. A signal line that indicates a new data value is available is connected to pin P1.0. Use an interrupt to detect a rising edge on the P1.0. When an interrupt is triggered the value on Port2 should be stored into a byte array of 32 entries. When 32 samples have been collected, P1.7 should be driven as an output high to indicate the memory is “full”

More Related