1 / 78

PCI 6 th Edition

PCI 6 th Edition. Compression Component Design. Presentation Outline. Interaction diagrams Columns example Second order effects Prestress wall panel example. Compression Members. Proportioned on the basis of strength design.

Download Presentation

PCI 6 th Edition

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. PCI 6th Edition Compression Component Design

  2. Presentation Outline • Interaction diagrams • Columns example • Second order effects • Prestress wall panel example

  3. Compression Members • Proportioned on the basis of strength design. • Stresses under service conditions, particularly during handling and erection (especially of wall panels) must also be considered

  4. Design Basis • The procedures are based on Chapter 10 of the ACI Code • Recommendations of the PCI Committee on Prestressed Concrete Columns • Recommendations of the PCI Committee on Sandwich Wall Panel Columns

  5. Design Process • The capacity determined by constructing a capacity interaction curve. • Points on this curve are calculated using the compatibility of strains and solving the equations of equilibrium as prescribed in Chapter 10 of the Code (ACI).

  6. Reinforcement • ACI 318-02 waives the minimum vertical reinforcement requirements for compression members if the concrete is prestressed to at least an average of 225 psi after all losses • In addition, the PCI Recommended Practice permits the elimination of lateral ties if: • Compression-controlled section • Non-prestressed reinforcement is not considered in the calculation of Pn • Non-prestressed reinforcement which is added for tension (e.g., for handling) is not considered in the calculation of Pn • The nominal capacity is multiplied by 0.85

  7. Development Length • Mild Reinforcement and prestressed development length can play a significant role in capacity • Additional Mild steel or special termination anchorages may be required • Mechanical bar termination methods • Threaded ends • Anchored to end plates

  8. Interaction Diagrams • Separate curves X, Y for none rectangular cross sections • Most architectural precast column sections are not rectangular, therefore it is necessary to calculate the actual centroid of the compression area

  9. Interaction Diagram Steps Step 1 – Determine Po pure axial capacity Step 2 – Determine maximum moment Step 3 – Determine Mo for Pn= 0 Step 4 – Determine additional points Step 5 – Calculate the maximum factored axial resistance specified by the Code as: • 0.80fPo for tied columns • 0.85fPo for spiral columns

  10. Step 1 – Determine Po for Mn= 0

  11. Step 1 – Determine Po for Mn= 0 Pn Pn, Mn fPn, fMn Mn

  12. Step 2 – Determine Maximum Moment • For members with non-prestressed reinforcement, this is the balance point • For symmetrical prestressed members, it is sufficiently precise to assume that the point occurs when the compression block, a, is one-half the member depth.

  13. Step 2 – Determine Maximum Moment • Neutral Axis Location, c Where: fy = the yield strength of extreme tension steel Es = Modulus of elasticity of extreme tension steel d = depth to the extreme tension steel from the compression face of the member

  14. Step 2 – Determine Maximum Moment • Determine the force in steel using strain compatibility Where: ds = Depth of steel es = Strain of steel Es = Modulus of elasticity of reinforcing steel fs = Force in steel

  15. Step 2 – Determine Maximum Moment • Maximum Axial Force Where: Acomp = Compression area A’s = Area of non prestressed compression reinforcing A’ps = Area of compression prestressing reinforcing As = area of reinforcing at reinforcement level y’ = distance from top of c.g. to Acomp

  16. Step 2 – Determine Maximum Moment

  17. Step 2 – Determine Maximum Moment Pn Pn, Mn fPn,fMn Mn

  18. Step 3 – Determine Mo for Pn= 0 • Same methods used in flexural member design Where: and

  19. Step 3 – Determine Mo for Pn= 0 Pn, Mn fPn, fMn Pn Mn

  20. Step 3 – Determine Mo for Pn= 0 Pn, Mn fPn, fMn Compression controlled (f = 0.65 or 0.70) Pn Tension controlled (f = 0.9) Mn

  21. Step 4 – Additional Points • Select a value of “c” and calculate a = β1c • Determine the value of Acomp from the geometry of the section • Determine the strain in the reinforcement assuming that εc= 0.003 at the compression face of the column. For prestressed reinforcement, add the strain due to the effective prestress εse= fse/Eps

  22. Step 4 – Additional Points • Determine the stress in the reinforcement. For non-prestressed reinforcement

  23. Step 4 – Additional Points • For prestressed reinforcement, the stress is determined from a nonlinear stress-strain relationship

  24. Step 4 – Additional Points • If the maximum factored moment occurs near the end of a prestressed element, where the strand is not fully developed, an appropriate reduction in the value of fps should be made

  25. Step 4 – Additional Points • Calculate fPn and fMn • For compression controlled sections (without spiral reinforcement) the net tensile strain εt in the extreme tension steel has to be less than or equal to that at the balance point • f = 0.65

  26. Step 4 – Additional Points Pn, Mn fPn, fMn Pn Mn

  27. Step 5 – Calculate the Maximum Factored Axial Pmax – = 0.80fPo for tied columns = 0.85fPo for spiral columns

  28. Step 5 – Calculate the Maximum Factored Axial Pn, Mn fPn, fMn 0.80fPo or 0.85fPo Pn Mn

  29. Example, Find Interaction Diagramfor a Precast Column Given: Column cross section shown Concrete: f′c = 5000 psi Reinforcement: Grade 60 fy= 60,000 psi Es= 29,000 ksi Problem: Construct interaction curve for bending about x-x axis

  30. Solution Steps Initial Step: Determine Column Parameters Step 1 – Determine Po from Strain Diagram Step 2 – Determine Pnb and Mnb Step 3 – Determine Mo Step 4 – Plot and add points as required Step 5 – Calculate maximum design load

  31. Determine Column Parameters β1 = 0.85 – 0.05 = 0.80 d = 20 – 2.5 = 17.5 in d′ = 2.5 in 0.85f′c = 0.85(5) = 4.25 ksi Ag = 12(20) = 240 in2 As = As′ = 2.00 in2 yt = 10 in

  32. Step 1 – Determine Po From Strain Diagram With no prestressing steel, the equation reduces to:

  33. Step 2 – Determine Pnb and Mnb • From Strain Diagram determine Steel Stress

  34. Step 2 – Determine Pnb and Mnb • Determine Compression Area

  35. Step 2 – Determine Pnb and Mnb • With no prestressing steel Pnb = (Acomp-A′s)(0.85f′c) +A′s f′s - As fs = (100.8 - 2)(4.25) + 2 (60)- 2(60) = 419.9 kips f Pnb = 0.65(419.9) = 273 kips

  36. Step 2 – Determine Pnb and Mnb • With no prestressing steel Mnb = (Acomp − A′s)(yt − y′)(0.85f′c) + A′sf′s(yt − d′) + Asfs(d − yt) = (100.8 – 2)(10 – 4.20)(4.25) + 2(60)(10 – 2.5) + 2(60)(17.5 – 10) = 2435 + 900 + 900 = 4235 kip-in. fMnb = 0.65(4235 kip-in.) = 2752 kip-in. = 229 kip-ft

  37. Step 3 – Determine Mo • Conservative solution neglecting compressive reinforcement

  38. Step 3 – Determine Mo • Strength Reduction Factor

  39. From the previous 3 steps, 3 points have been determined. From these 3 points, a conservative 3 point approximation can be determined. Add additional points as required Step 4 – Plot 3 Point Interaction

  40. Step 5 – Calculate Maximum Design Load Pmax= 0.80 fPo = 0.80 (808 kips) = 646 kips

  41. Wall or Column • Effective Width is the Least of • The center-to-center distance between loads • 0.4 times the actual height of the wall • 6 times the wall thickness on either side

  42. Slenderness / Secondary Effects

  43. Causes of Slenderness Effects • Relative displacement of the ends of the member due to: • Lateral or unbalanced vertical loads in an unbraced frame, usually labeled “translation” or “sidesway.” • Manufacturing and erection tolerances

  44. Causes of Slenderness Effects • Deflections away from the end of the member due to: • End moment due to eccentricity of the axial load. • End moments due to frame action continuity, fixity or partial fixity of the ends • Applied lateral loads, such as wind • Thermal bowing from differential temperature • Manufacturing tolerances • Bowing due to prestressing

  45. Calculation of Secondary Effects • ACI allows the use of an approximate procedure termed “Moment Magnification.” • Prestressed compression members usually have less than the minimum 1% vertical reinforcement and higher methods must be used • The PCI Recommended Practice suggests ways to modify the Code equations used in Moment Magnification, but the second-order, or “P-∆” analysis is preferred

  46. Second-Order (P-∆) Analysis • Elastic type analysis using factored loads. • Deflections are usually only a concern under service load, the deflections calculated for this purpose are to avoid a stability failure • The logic is to provide the same safety factor as for strength design

  47. Second-Order (P-∆) Analysis • Iterative approach • Lateral deflection is calculated, and the moments caused by the axial load acting at that deflection are accumulated • Convergence is typical after three or four iterations • If increase in deflection is not negligible the member may be approaching stability failure

  48. Second-Order (P-∆) Analysis • Cracking needs to be taken into account in the deflection calculations • The stiffness used in the second order analysis should represent the stiffness of the members immediately before failure • May involve iterations within iterations • Approximations of cracked section properties are usually satisfactory

  49. Second-Order (P-∆) Analysis • Section 10.11.1 of ACI 318-02 has cracked member properties for different member types for use in second-order analysis of frames • Lower bound of what can be expected for equivalent moments of inertia of cracked members and include a stiffness reduction factor fK to account for variability of second-order deflections

  50. Second-Order (P-∆) Analysis • Effects of creep should also be included. The most common method is to divide the stiffness (EI) by the factor 1 + βd as specified in the ACI moment magnification method • A good review of second-order analysis, along with an extensive bibliography and an outline of a complete program, is contained in Ref. 24.

More Related