1 / 34

Routine Field Techniques

Routine Field Techniques. Streamflow Record Computation using ADVMs and Index Velocity Methods Office of Surface Water. Overview. Overview. Tip Sheets in IV T&M Report - Appendix 2. Download Data. Download datalogger /DCP data Download ADVM internal recorder data. Connect to ADVM.

nira
Download Presentation

Routine Field Techniques

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Routine Field Techniques Streamflow Record Computation using ADVMs and Index Velocity Methods Office of Surface Water

  2. Overview

  3. Overview

  4. Tip Sheets in IV T&M Report - Appendix 2

  5. Download Data • Download datalogger/DCP data • Download ADVM internal recorder data

  6. Connect to ADVM • Connect ADVM cable to computer through 9-pin serial port or USB-serial adapter • Open ADVM software and select communication settings

  7. Changing Between SDI-12 and RS-232 • SonTek ADVMs have a jumper plug • Plug together when communicating using computer • Unplug when in SDI-12 mode and controlled by DCP Plugged In = RS-232 Mode Unplugged = SDI-12 Mode

  8. Review Data

  9. Review Data - Brief Time Series Review

  10. What to Look For? • Focus on problems that could be resolved in field • Obstruction in sampling volume • Change in ADVM orientation • Sediment or biofouling on beams • Beam failure • Thermistor failure • Change in cell end due to reduced scatterers or other problem • ADVM stopped working • Should be a brief review to look for major problems! • More thorough review will be done in office

  11. Problems

  12. More Problems

  13. Erase Recorder • Again, ensure data file is complete and saved to your computer • Rename file according to your Office’s QA Plan • Recommend erasing recorder each time to reduce chance of filling recorder and losing data • CAUTION: Once erased, data cannot be recovered!

  14. Example of Data File Naming

  15. Record a Log File • Capture current configuration settings and any changes to settings by recording a “log” file • Changes to measurement volume • Time/date before and after clock sync • Changes to averaging period/measurement interval • In SonUtils, go to File – Open Log File. Click “Show….” buttons to capture current settings • Log file will capture all commands entered in software until you close file • Archive when back in the office

  16. Check and Sync Clocks • Check and, if needed, sync clocks in DCP, ADCP, and ADVM • Within 1-2 seconds Correct Time: www.time.gov http://tf.nist.gov/

  17. Check ADVM Temperature • Per OSW Memo 2010.07….An independent water temperature measurement must be made and documented during each site visit to an index velocity station. • Temperature must match within 2o C • Make comparison beside ADVM if at all possible

  18. Beam Check • Collect a beam check • Turn averaging “on” in SonTek ADVMs • Record a minimum of 50 pings

  19. Beam Checks – Look for Problems • Obstructions? • Sidelobe problems? • Signal Amplitudes 10-20 counts above noise level at Cell End? • Changing Cell End? • Signal Amplitudes similar for each beam?

  20. Examples of Problems What would you do about these problems in the field?

  21. Retrieve ADVM

  22. Clean ADVM

  23. Clean ADVM • Remove biofouling, debris, sediment, ice • Use soft bristle brushes where possible

  24. Check ADVM Alignment • Has mount moved? • Has ADVM moved on mount? • How could you tell?

  25. Redeploy ADVM

  26. Another Beam Check • Perform another beam check if: • First one showed a problem • Cleaning removed a lot of biofouling or sediment • ADVM alignment was altered

  27. Configure ADVM For Q Measurements • Change averaging interval and measurement period of ADVM to 1 minute during Qms • Change in ADVM and allow to record internally during Qm • May also need to change stage readings to 1 minute

  28. Make Q Measurement

  29. Re-Connect With ADVM • Re-connect and download 1-minute data • Change averaging period and measurement interval back to regular settings • Any other configuration changes? • Remember to record a log file!

  30. Re-Deploy ADVM • May need to set a start date/time in ADVM • If controlled by datalogger, put in SDI-12 mode • Example for SonTek ADVM…. • Unplug jumper! • Make sure ADVM and DCP are working

  31. Documentation • SWAMI • IV Gage Inspection Form

  32. SWAMI • As of June 2012, SWAMI does not allow for any field entry of index-velocity specific information for discharge measurements • Cannot use SWAMI to calculate percent differences • Index-velocity ratings are not available to view • If index-velocity for a measurement is calculated in the field it can be put into a comment box for later entry into SiteVisit • A request enhancement has been submitted by the HAWG for a separate index-velocity inspection tab and integration into the discharge measurement screens

  33. SWAMI • If your index meter is set up in SiteVisit, you can enter readings same as a stage gage

  34. Questions?

More Related