1 / 33

ZIGBEE

ZIGBEE. 1. Equipment. FT-6200 High-power Zigbee Starter Kit. Equipment (cont’). FT-6250 Base Development Board. Equipment (cont’). FT-6251 Sensor Development Board Temperature range 0℃ ~ 70℃ Humidity range 0% ~ 95%. Experiment: Setup environment. Goal Setup environment

nathan-mueller
Download Presentation

ZIGBEE

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ZIGBEE 1

  2. Equipment • FT-6200 High-power Zigbee Starter Kit

  3. Equipment(cont’) • FT-6250 • Base Development Board

  4. Equipment(cont’) • FT-6251 • Sensor Development Board • Temperature range • 0℃ ~ 70℃ • Humidity range • 0% ~ 95%

  5. Experiment: Setup environment • Goal • Setup environment • Install the development tool • Understand the program • Build the program • Burn image file into Zigbee

  6. Experiment: Setup environment

  7. Experiment: Setup environment • Jennic SDKhas two development tools • Command Line Interface (CLI) • Integrated Development Environment (IDE)

  8. Experiment: Setup environment ? • Install JN-SW-4031-SDK-Toolchain-v1.1.exe • JN-SW-4030-SDK-Libraries-v1.4.exe • Download from http://www.jennic.com/“Support / software”

  9. Experiment: Setup environment • Install JN-SW-4027-SDKwithCLI.msi • Download from http://www.jennic.com/“Support / software”

  10. Experiment: Setup environment • 將範例程式解壓縮至C:\Jennic\cygwin\jennic\SDK\Application • ExecuteCode::Blocks

  11. Experiment: Setup environment

  12. Experiment: Setup environment • Execute Jennic Flash Programmer

  13. Experiment: Setup environment • Installation document • CDROM\Document\Installation\JN-UG-3035-SDK-Installation-1v2.pdf

  14. Experiment: LED Flash • Goal • Understand the program • Modify the program • Step1: LED A flash twice, go to step2 • Step2: LED B flash twice, go to step1

  15. Start AppColdStart AppWarmStart InitSystem While(true) Yes No Timer? Yes True False Flag LED1 on LED2 off LED1 off LED2 on Experiment: LED Flash • Program

  16. Experiment: LED Flash • Demo

  17. Experiment: LED Flash • Function library • CDROM\Documents\Board\JN-RM-2001-Integrated-Peripherals-API-2v3.pdf

  18. Experiment: Button Control LED • Goal • 在 FT625x 無線傳輸設備上學習使用按鈕的方式以控制LED燈號。 • Understand the program • Modify the program • Step1: Press button A, start LED flash • Step2: Press button B, stop LED flash • Draft flow chart of the modified program

  19. Experiment: Button Control LED • Execute Code::Blocks

  20. Experiment: Button Control LED

  21. Experiment: Button Control LED • Demo

  22. Experiment: UART Control LED • Goal • 在 FT625x無線傳輸設備上學習可以透過UART通訊從設備上取得一些資訊回饋(feedback)。 • Understand the program • Modify the program • PC sends message through serial port to turn on\off the LED

  23. Experiment: UART Control LED • Execute Code::Blocks

  24. Experiment: UART Control LED • Demo Terminal Serial Port Typing in HyperTerminal:ex: aaaaabbbcc FT 6250 UART which UART ASCII code

  25. Experiment: UART Control LED • 使用超級終端機，必須做相關設定如下: 38400 bps, 8 data bits, no parity, 1 stop bit, and no handshaking. • 燒錄程式到FT-6200無線傳輸設備後，務必先重置電源，再接上與超級終端機的連線。

  26. Experiment: Wireless Control LED • Goal • 在 FT625x無線傳輸設備上學習如何使用RF無線傳輸，形成小型無線網路。 • Understand program • Modify the program • PC sends message through wireless to turn on\off the LED • Write the difficult point down while you are experimenting

  27. Experiment: Wireless Control LED • Execute Code::Blocks

  28. Experiment: Wireless Control LED • Architecture

  29. Experiment: Sensor • Goal • 學習如何使用Zigbee裝置收集週遭環境的溫度和溼度，並透過所在無線網路傳遞這些資訊 • Understand program • Modify the program • 讓end device定期回報所感測到的溫溼度數據到coordinator • 設定溫溼度MAX的警告條件 • 溫度警告 - LED_0 閃爍 • 濕度警告 - LED_1 閃爍 請攜帶吹風機

  30. Experiment: Sensor • Execute Code::Blocks

  31. Experiment: Sensor • Demo

  32. Experiment: Flow Testing • Goal • 測試Zigbee Coordinator和End Device的最高傳輸速度 • 速度是否可達到20k-250k bps，如不行請評估原因 • Devices • Zigbee • Smartbits 600

  33. Experiment: Flow Testing SmartBits 600

More Related