1 / 72

Michael Aquilino Microelectronic Engineering Department Rochester Institute of Technology

Development of a Deep-Submicron CMOS Process for Fabrication of High Performance 0.25  m Transistors. Michael Aquilino Microelectronic Engineering Department Rochester Institute of Technology April 21, 2005. Motivation.

malo
Download Presentation

Michael Aquilino Microelectronic Engineering Department Rochester Institute of Technology

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Development of a Deep-Submicron CMOS Process for Fabrication of High Performance 0.25 m Transistors Michael Aquilino Microelectronic Engineering Department Rochester Institute of Technology April 21, 2005

  2. Motivation • Enable the Microelectronic Engineering department to continue the semiconductor industry trend of fabricating high performance transistors that have faster switching speeds, increased density and functionality, and ultimately a decrease in cost per function. • Push the limits of the SMFL in all areas from design to fabrication to test • Create a baseline process that can be used to integrate strained silicon, metal gates, high-k gate dielectrics, and replacement gate technologies at RIT 2

  3. Outline • RIT/Industry Scaling Trends • Gate Control Fundamentals • Short Channel Effects • Deep-Submicron Scaling • Unit Process Development • Layout • Integration/Fabrication/Test • Time Line • Questions 3

  4. RIT/Industry Scaling Trends Table 1: RIT/Industry Scaling Trends [3] • Over last 30 years, transistors have gotten smaller and faster • 110x reduction in gate length • 36,000x increase in switching speed • Integrated circuits have become much more complex • 54,000x increase in number of transistors on an IC 4

  5. RIT/Industry Scaling Trends Table 1: RIT/Industry Scaling Trends [3] • In May of 2004 an NMOS transistor with LPOLY = 0.5 µm was developed • This is RIT’s smallest transistor with LEFFECTIVE = 0.4 µm • This is the same technology as the Intel Pentium from 9 years earlier 5

  6. RIT/Industry Scaling Trends Table 1: RIT/Industry Scaling Trends [3] • By September of 2005, this process will yield CMOS transistors • with LPOLY = 0.25 µm and LEFFECTIVE = 0.18 µm • This technology was used in high volume manufacturing of the Intel • Pentium III at 600 MHz only 6 years ago • The gap between industry and RIT is rapidly shrinking 6

  7. Outline • RIT/Industry Scaling Trends • Gate Control Fundamentals • Short Channel Effects • Deep-Submicron Scaling • Unit Process Development • Layout • Integration/Fabrication/Test • Time Line • Questions 7

  8. Gate Control Fundamentals • NMOS Transistor • 4 Terminal Device • Gate • Source • Drain • Body • To turn transistor on: • Apply positive charge to Gate, QG • A depletion region in the p-type body is created as positively • charged holes are repelled by gate, exposing negatively charged • acceptor ions, QB • As the gate charge is further increased, electrons from the source • diffuse into the channel and become inversion charge, QI • QG = QB + QI Figure 1: Schematic of NMOS Transistor [4] 8

  9. Gate Control Fundamentals • The source and body • terminals are grounded • A positive voltage is • applied to the drain, VDS • Inversion charge moves • from source to drain and • is the current in the device Figure 1: Schematic of NMOS Transistor [4] • Equation 1 shows the classical derivation for drain current in a • transistor by integrating the inversion charge along the channel (Eq. 1) 9

  10. Gate Control Fundamentals • A depletion region from • the drain is created by the • reverse biased body-drain • p-n+ diode • The positively charged • donor ions in drain support • some of the negative • inversion charge • This is known as “Charge Sharing” as the gate does not have full • control over the inversion channel • For large gate lengths, the contribution of the drain in controlling • the inversion layer is small compared to the gate contribution • As transistors are scaled smaller in gate length, the drain has a • larger percentage contribution in supporting inversion charge in • the channel Figure 1: Schematic of NMOS Transistor [4] 10

  11. Outline • RIT/Industry Scaling Trends • Gate Control Fundamentals • Short Channel Effects • Deep-Submicron Scaling • Unit Process Development • Layout • Integration/Fabrication/Test • Time Line • Questions 11

  12. Short Channel Effects • “Gate Control” is the most important concept in scaling of transistors • The consequence of the drain taking control away from the gate • is short channel effects such as: • VT Roll-off • Drain Induced Barrier Lowering (DIBL) • Punch-through • Threshold voltage decreases • as gate length decreases • For small enough gate lengths • the devices will be on at 0 V Figure 2 : VT Roll-off Effect [1] 12

  13. Short Channel Effects • “Gate Control” is the most important concept in scaling of transistors • The consequence of the drain taking control away from the gate • is short channel effects such as: • VT Roll-off • Drain Induced Barrier Lowering (DIBL) • Punch-through • Increased off-state leakage with • increase in drain voltage • If gate were in full control, these • curves would be one on top of the • other Figure 3: Drain Induced Barrier Lowering (DIBL) [1] 13

  14. Short Channel Effects • “Gate Control” is the most important concept in scaling of transistors • The consequence of the drain taking control away from the gate • is short channel effects such as: • VT Roll-off • Drain Induced Barrier Lowering (DIBL) • Punch-through • At high drain bias, the drain • takes control of current • through the device • Excessive heating can occur • and cause device failure Figure 4: Lateral source/drain Punch-through [4] 14

  15. Short Channel Effects • “Gate Control” is the most important concept in scaling of transistors • The consequence of the drain taking control away from the gate • is short channel effects (SCE) such as: • VT Roll-off • Drain Induced Barrier Lowering (DIBL) • Punch-through • Transistors with short channel effects are undesirable • These SCE must be minimized to yield long-channel transistors 15

  16. Outline • RIT/Industry Scaling Trends • Gate Control Fundamentals • Short Channel Effects • Deep-Submicron Scaling • Unit Process Development • Layout • Integration/Fabrication/Test • Time Line • Questions 16

  17. Table 2: 0.25 µm Scaling Parameters from NTRS Roadmap [6] Figure 5: Physical Scaling Guidelines [7] Deep-Submicron Scaling • The goal in deep-submicron scaling is to maximize the gate control for switching the device on and off by scaling physical and electrical parameters 17

  18. Table 2: 0.25 µm Scaling Parameters from NTRS Roadmap [6] Figure 5: Physical Scaling Guidelines [7] Deep-Submicron Scaling • The goal in deep-submicron scaling is to maximize the gate control for switching the device on and off by scaling physical and electrical parameters • Decrease gate oxide thickness • Gate is closer to the channel • More control in switching device off • Cox since Cox = A/tox or Cox =Q/V • ID and gm since  Cox 18

  19. Table 2: 0.25 µm Scaling Parameters from NTRS Roadmap [6] Figure 5: Physical Scaling Guidelines [7] Deep-Submicron Scaling • The goal in deep-submicron scaling is to maximize the gate control for switching the device on and off by scaling physical and electrical parameters • Decrease junction depth of source/drain • Depletion region from gate dominates • depletion region from the drain • Trade-off is sheet resistance  and ID  • ND must  which will cause RS 19

  20. Table 2: 0.25 µm Scaling Parameters from NTRS Roadmap [6] Figure 5: Physical Scaling Guidelines [7] Deep-Submicron Scaling • The goal in deep-submicron scaling is to maximize the gate control for switching the device on and off by scaling physical and electrical parameters • Use sidewall spacer to create deeper • source/drain junction called the contact • Typically ~2x as deep as shallow LDD • Doped heavily to reduce RS 20

  21. Table 2: 0.25 µm Scaling Parameters from NTRS Roadmap [6] Figure 5: Physical Scaling Guidelines [7] Deep-Submicron Scaling • The goal in deep-submicron scaling is to maximize the gate control for switching the device on and off by scaling physical and electrical parameters • Increase doping of channel to decrease • the depletion region from the source/drain • Use a retrograde profile where doping is • low at the surface and higher sub-surface • Mobility of carriers  • ID and gm since both are  mobility 21

  22. Table 2: 0.25 µm Scaling Parameters from NTRS Roadmap [6] Deep-Submicron Scaling • The goal in deep-submicron scaling is to maximize the gate control for switching the device on and off by scaling physical and electrical parameters • As TOX, gate leakage current  • VDD must  to reduce this leakage • VT must  so (VGS-VT) , this is “Gate Overdrive” and is  ID • Want ION  since gate delay  ION-1 22

  23. Table 2: 0.25 µm Scaling Parameters from NTRS Roadmap [6] Deep-Submicron Scaling • The goal in deep-submicron scaling is to maximize the gate control for switching the device on and off by scaling physical and electrical parameters • Want IOFF to be low to reduce standby power • The industry standard metric is 1 nA/µm of off-current • This results in 5.75 decades between ION and IOFF • There is 500 mV swing between 0 V and VT • SS of 85 mV/decade is needed to turn the device off Theoretical limit ~ 60 mV/decade @ 300K 23

  24. Outline • RIT/Industry Scaling Trends • Gate Control Fundamentals • Short Channel Effects • Deep-Submicron Scaling • Unit Process Development • Layout • Integration/Fabrication/Test • Time Line • Questions 24

  25. Super Steep Retrograde Twin Well • Nitride Sidewall Spacers • Rapid Thermal Dopant Activation • 2 Level Aluminum Metallization • Back End CMP • Shallow Trench Isolation • Dual Doped Poly Gates • 50 Å gate oxide w/ N2O • Low Doped Source/Drain Extensions • Titanium Silicide 0.25 µm Device Technology • Unit Processes will be developed to yield cross-section shown in Figure 6 Figure 6: CMOS Cross Section showing NMOS (left) and PMOS (right) Transistors 25

  26. Unit Process Development • Shallow Trench Isolation • Channel Engineering • Uniformly Doped Twin Well • Super Steep Retrograde Well • Ultra Thin Gate Oxide • Gate Formation • Lithography • Resist Trimming • Reactive Ion Etch (RIE) of Gate • Source/Drain/Gate Doping • Poly re-ox • Low Doped Source/Drain Extensions • Sidewall Spacers • Source/Drain Contacts • Dual Doped Poly • Rapid Thermal Dopant Activation • Titanium Salicide • Contact Cut Etch • 2 Level Aluminum Metallization Figure 7: Shallow Trench Isolation 26

  27. Shallow Trench Isolation • Replacement of LOCOS as preferred isolation technology • LOCOS suffers from “Bird’s Beak” effect • Field oxide encroaches into active region, reducing W • Reduction in Width leads to reduction in drive current • To recover this loss, transistors must be made wider • which takes up more real estate • Small geometries are not possible since Bird’s Beak • oxide encroaches from both sides of active area • With STI, WACTUAL ≈ WDRAWN • Increased packing density • Higher drive current for devices with same WDRAWN • Decreased topography early in the process 27

  28. Shallow Trench Isolation • Grow Pad Oxide • Deposit Nitride by LPCVD • Pattern and Etch Silicon Trench • Grow liner oxide to repair silicon • and round off sharp corners • Fill with PECVD TEOS Oxide • CMP trench oxide • Use Nitride as etch stop • Remove Nitride in H3PO4 acid Figure 8: STI Process after trench etch Figure 9: STI Process after trench fill Figure 10: STI Process after CMP 28

  29. Unit Process Development • Shallow Trench Isolation • Channel Engineering • Uniformly Doped Twin Well • Super Steep Retrograde Well • Ultra Thin Gate Oxide • Gate Formation • Lithography • Resist Trimming • Reactive Ion Etch (RIE) of Gate • Source/Drain/Gate Doping • Poly re-ox • Low Doped Source/Drain Extensions • Sidewall Spacers • Source/Drain Contacts • Dual Doped Poly • Rapid Thermal Dopant Activation • Titanium Salicide • Contact Cut Etch • 2 Level Aluminum Metallization 29

  30. Channel Engineering Figure 11: Uniformly Doped Twin Wells Figure 12: Super Steep Retrograde Wells • Uniformly Doped Twin Wells • NMOS built in p-well • PMOS built in n-well • Set Field VT to stop parasitic • conduction channels from • forming between adjacent • devices • Super Steep Retrograde Wells • 2nd step in well formation process • Lower doping at surface which • transitions to higher doping • sub-surface • Control short channel effects • Set active VT 30

  31. Uniformly Doped Twin Well • In industry, wells are implanted through • the trench oxide with energies of 1 MeV • to place the peak 1 µm below the surface • The limit of the Varian 350D Ion Implanter • is 190 KeV which is not high enough to • implant through 3000 Å of trench oxide • Also, there will be non-uniformities in silicon trench depth and • TEOS oxide fill. • For packing density purposes, multiple active regions are built in the same well with 1 common contact • It is therefore required for the well doping to be continuous under the trench oxide regions • For this process, the wells will be implanted before the trench oxide • fill in the STI process to ensure the wells are continuous in the field Figure 11: Uniformly Doped Twin Wells 31

  32. Uniformly Doped Twin Well Table 3: Field Region VT Figure 11: Uniformly Doped Twin Wells • A drive-in thermal step will create uniform wells with: • ND = 1x1017 cm-3 • XJ-WELL = 1 µm • With a 2.0 V supply, the field-VT is sufficiently large • The junction depth of the wells must be large enough to prevent • vertical punch-through between the reverse-biased drain and • complimentary doped starting wafer • A junction depth of 1 µm will provide more than enough tolerance 32

  33. Super Steep Retrograde Well Figure 12: Super Steep Retrograde Wells • Increased carrier mobility due to lower channel doping at surface • Increased drive current due to increased mobility • Suppression of short channel effects (SCE) such as VT roll-off, punch- • through, and drain induced barrier lowering (DIBL) due to the higher • peek doping sub-surface • Latch-up is suppressed because the base regions of parasitic BJTs are • doped higher, therefore reducing their gain. 33

  34. Super Steep Retrograde Well Figure 12: Super Steep Retrograde Wells • Increased carrier mobility due to lower channel doping at surface • Increased drive current due to increased mobility • Suppression of short channel effects (SCE) such as VT roll-off, punch- • through, and drain induced barrier lowering (DIBL) due to the higher • peek doping sub-surface • Latch-up is suppressed because the base regions of parasitic BJTs are • doped higher, therefore reducing their gain. 34

  35. Super Steep Retrograde Well Peak channel concentration Lower surface doping concentration Uniform well for Field VT Figure 13: Super Steep Retrograde Profile [10] • Implanted after uniformly doped wells go through drive-in • In Industry, heavy ions that are slow diffusers are used: • Indium (In) is used for p-well of NMOS • Antimony (Sb) or Arsenic (As) are used for n-well of PMOS • At RIT, Boron and Phosphorous are available • Boron (B) will be used for p-well of NMOS • Phosphorous (P) will be used for n-well of PMOS • Are more susceptible to transient enhanced diffusion (TED) • Won’t produce profiles as steep as In or Sb but by keeping • thermal budget low, can still produce retrograde profiles 35

  36. Unit Process Development • Shallow Trench Isolation • Channel Engineering • Uniformly Doped Twin Well • Super Steep Retrograde Well • Ultra Thin Gate Oxide • Gate Formation • Lithography • Resist Trimming • Reactive Ion Etch (RIE) of Gate • Source/Drain/Gate Doping • Poly re-ox • Low Doped Source/Drain Extensions • Sidewall Spacers • Source/Drain Contacts • Dual Doped Poly • Rapid Thermal Dopant Activation • Titanium Salicide • Contact Cut Etch • 2 Level Aluminum Metallization 36

  37. 50 Å Gate SiO2 with N2O Incorporation Figure 14: Ultra Thin Gate Oxide • NTRS Roadmap suggests 40 – 50 Å, target for this process is 50 Å • ox = 4 MV/cm, this is at limit of Fowler-Nordheim tunneling • Nitrogen is incorporated into oxide to block diffusion of boron from • p+ poly gate into channel of PMOS transistor • Surface Charge Analysis can be done to determine density of interface • trap states. 37

  38. Unit Process Development • Shallow Trench Isolation • Channel Engineering • Uniformly Doped Twin Well • Super Steep Retrograde Well • Ultra Thin Gate Oxide • Gate Formation • Lithography • Resist Trimming • Reactive Ion Etch (RIE) of Gate • Source/Drain/Gate Doping • Poly re-ox • Low Doped Source/Drain Extensions • Sidewall Spacers • Source/Drain Contacts • Dual Doped Poly • Rapid Thermal Dopant Activation • Titanium Salicide • Contact Cut Etch • 2 Level Aluminum Metallization Figure 15: Poly Gate Formation 38

  39. Gate Formation - Lithography Figure 16: ASML DUV Stepper Figure 17: Canon i-line Stepper • Canon FPA-2000i1 stepper • 365 nm i-line source • Capable of 0.5 µm lines/spaces • Standard resist coat/develop track • Capable of 0.05 µm overlay error • ASML PAS 5500/90 stepper • 248 nm KrF excimer laser • Capable of 0.25 µm lines/spaces • Tool is currently down, laser 39

  40. Gate Formation – Resist Trimming Figure 18: Resist Trimming Process • Resist trimming can be used to make 0.5 µm line a 0.25 µm line for gate • Isotropically etch 1250 Å of resist of sides and top of 0.5 µm line • Resist thickness reduced from 10,000 Å to 8750 Å • This is still sufficiently thick to protect poly during gate plasma etch • Line width reduced to 0.25 µm target in photoresist • This technique will be explored if over-exposing/developing is not successful 40

  41. Gate Formation – RIE Poly • Polysilicon thickness is reduced for smaller gate lengths • 2500 Å target will provide 1:1 aspect ratio for plasma etch • Will block up to 50 keV Phosphorous and 30 keV Boron • Want high selectivity of poly to oxide since oxide is very thin • Reactive Ion Etcher will be used since it etches anisotropically • Etch rate is higher in the vertical direction compared to horizontal • If etch was isotropic, enough under-cut would occur due to lateral • etching that 0.25 µm would be etched away and remove the • photoresist masking layer Figure 19: Under-Cut of Gate Mask 41

  42. Unit Process Development • Shallow Trench Isolation • Channel Engineering • Uniformly Doped Twin Well • Super Steep Retrograde Well • Ultra Thin Gate Oxide • Gate Formation • Lithography • Resist Trimming • Reactive Ion Etch (RIE) of Gate • Source/Drain/Gate Doping • Poly re-ox • Low Doped Source/Drain Extensions • Sidewall Spacers • Source/Drain Contacts • Dual Doped Poly • Rapid Thermal Dopant Activation • Titanium Salicide • Contact Cut Etch • 2 Level Aluminum Metallization 42

  43. Poly Re-Oxidation • After plasma etch of gate there is damage to edges of gate oxide • A 250 Å oxide will be thermally grown to: • Repair damage to gate oxide from • plasma etch of the poly gate • Create a thicker screening oxide for • source/drain extension implant • Make a thicker etch stop for sidewall • spacer etch process • Form an off-set region for lateral diffusion of shallow s/d extension • Want to reduce gate overlap of s/d to reduce Miller Capacitance • This capacitance will reduce the cut-off frequency of the device • Need 15 – 20 nm overlap or drive current will degrade [11] Figure 20: Poly Re-Oxidation 43

  44. LPOLY = 250 nm XJ = 75 nm 52.5 nm 52.5 nm LEFFECTIVE = 180 nm Poly Re-Oxidation Figure 21: Gate Overlap and LEFFECTIVE Calculation • Gate Overlap = 52.5 nm – 25 nm = 27.5 nm ≥ 15 – 20 nm requirement • Process is designed for LPOLY = 0.25 µm and LEFFECTIVE = 0.18 µm 44

  45. Low Doped Source/Drain Extensions • Shallow junctions implanted after • poly re-ox step • A portion of VDS is dropped across • the LDD so a lower effective voltage • is across the channel (Eq. 2) • The advantage of this is reduced • hot carrier effects since carriers see lower horizontal electric field • The trade-off is there will be a reduction in drive current & switching speed Figure 22: Low Doped Source/Drain Extensions Figure 23: Equivalent Circuit with Parasitic Resistance Vchannel = VDS – 2*IDS(Rterminal + Rs/d + RLDD) (Eq. 2) 45

  46. Low Doped Source/Drain Extensions Table 4: NTRS Guidelines for LDD Scaling [6] • Low end of range is chosen for XJ and RS so if more diffusion • occurs then is anticipated, the devices will still operate properly • The implant energy must be selected to place the peak of the • implant at the Silicon surface. With a 300 Å screening oxide layer: • B11 of 10 keV • P31 of 25 keV • The Varian 350D is capable of implant energies as low as 10 keV • In industry, Silicon (Si) or Germanium (Ge) are implanted before • the shallow S/D implants to reduce channeling of dopant ions 46

  47. Silicon Nitride Sidewall Spacers Figure 24: Nitride Sidewall Spacers Figure 25: SEM Micrograph of Nitride Spacer • Sidewall spacers are formed after the LDD implants to create an • offset region where a deeper source/drain contact region can be • implanted. Figure 26: Sidewall Spacer Process 47

  48. VDD = 2.0 V |VT| = 0.5 V Tox = 50 Å = 4108 µm Silicon Nitride Sidewall Spacers • In a perfectly anisotropic etch the Lspacer = tpoly = 0.25 µm • Parasitic LDD resistance is controlled by length of sidewall spacer (Eq. 3) (Eq. 4) Table 5: Sidewall Spacer Length Effect on Drive Current [9] • NTRS Guidelines require < 10% reduction in drive current due • to parasitic source/drain extension resistance • Source/Drain contact resistance must also be taken into account 48

  49. Source/Drain Contact • Source/Drain contacts implanted after sidewall spacer formation • and are self-aligned to the gate Figure 27: Source/Drain Contact and Gate Doping • Contact is doped higher and junction depth deeper to • decrease parasitic source/drain resistance • Silicide thickness must account for < ½ contact junction depth • or increased leakage current will result 49

  50. Source/Drain Contact Table 6: NTRS Guidelines for Source/Drain Contact Scaling [6] • Midpoint of XJ range chosen so XJ-CONTACT ~ 2*XJ-LDD • The implant energy must be ~ 2x higher then shallow LDD implants: • B11 of 20 - 30 keV • P31 of 40 - 50 keV • The sheet resistance of this region must be decreased to decrease • the reduction in drive current • The polysilicon gates are doped n+ for NMOS and p+ for PMOS at • the same time the contacts are doped. 50

More Related