1 / 17

Field Methods in Dendrochronology

Field Methods in Dendrochronology. Field Methods in Dendrochronology:. So, if you’ve selected your site and you can even see your trees. NOW WHAT? Two primary means of collecting wood samples: Increment borer Chain saw Forget the chain saw for this class …. The Increment Borer.

mala
Download Presentation

Field Methods in Dendrochronology

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Field Methods in Dendrochronology

  2. Field Methods in Dendrochronology: • So, if you’ve selected your site and you can even see your trees. NOW WHAT? • Two primary means of collecting wood samples: • Increment borer • Chain saw • Forget the chain saw for this class …

  3. The Increment Borer Pressler, M.R. 1866. Der forstliche Zuwachsbohrer neuester Construction. Tharandter forstliches Jahrbuch 17: 155-223.

  4. The Increment Borer (broken apart) Grissino-Mayer, H.D. 2003. A manual and tutorial for the proper use of an increment borer. Tree-Ring Research 59(2): 63-79.

  5. The Increment Borer (assembled) Grissino-Mayer, H.D. 2003. A manual and tutorial for the proper use of an increment borer. Tree-Ring Research 59(2): 63-79.

  6. Preparing the Increment Borer • Fasten auger onto the handle via the clip. • Spray inside and outside of auger with WD-40. • Place the extractor some place convenient (NOT on the ground). • Place the tip of the auger against the tree. • Breast height or ground level? • Are you coring on a slope? WHY does this matter? • Look for a furrow in the bark. Bark is GOOD. • Grasp the handle with one hand and the auger with the other. • Push and turn simultaneously. • Keep the shaft steady. Why is this important?

  7. Starting an Increment Borer (I)

  8. Starting an Increment Borer (II)

  9. Coring the Tree • Turn with both hands, even pressure on each handle. • Listen for “odd” sounds. If it sounds strange, stop immediately. • You do not want to “jam” the wood inside • This occurs when the inner portion of the core stops. • As you continue to turn, though, new wood is pushed against the jammed wood. • This creates an awful mess inside your borer, and sometimes renders your borer useless for the rest of the trip. • Jammed borers often must be cleared in a wood shop.

  10. Coring the Tree • Every few turns, check to see if the wood is jamming inside: 1. Insert the extractor until it hits the core. Mark this location with your thumb.

  11. Coring the Tree • Every few turns, check to see if the wood is jamming inside: 2. Pull the extractor out. Place the tip against the bark. Its distance should be the same as when it was inside the auger.

  12. Coring the Tree • Every few turns, check to see if the wood is jamming inside: 3. If your thumb is away from the handle, your wood is jamming! Stop immediately.

  13. Extracting the Core • Insert the extractor under the core. • Gently push the extractor the full length of the auger. • The teeth on the extractor will bite into the end of the core. • Turn one or two full turns out. • Pull the extractor gently to break the core from the tree. • Cradle the core as it exits the auger in case pieces fall off. • Insert the core immediately into a paper or plastic straw. • Label the straw with the proper ID.

  14. Extracting the Core

  15. Extracting the Core

  16. Wrapping up … • Write down tree and site information on standard field forms, including: • Height estimate, dbh, crown condition, aspect, slope, topography, vegetation, location (relative and GPS). • Photo documentation: helps in crossdating and archiving • Ensure all samples and equipment are accounted for before heading back. • Clean all your equipment!

  17. Using a Chain Saw

More Related