1 / 18

Gypsum Materials

Gypsum Materials. DA 122 Dental Materials. Applications for Gypsum. Used to make a model from an impression Use of model determines type of gypsum used Gypsums vary in Strength Dimensional accuracy Resistance Reproduction detail Water/powder ratio Setting times. Calcination.

lynn
Download Presentation

Gypsum Materials

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Gypsum Materials DA 122 Dental Materials

  2. Applications for Gypsum • Used to make a model from an impression • Use of model determines type of gypsum used • Gypsums vary in • Strength • Dimensional accuracy • Resistance • Reproduction detail • Water/powder ratio • Setting times

  3. Calcination • Manufacturing process used for gypsum production • Gypsum is mined rock; then ground into a fine powder • Powder is heated until specific amount of water is driven out of the gypsum = CALCINATION

  4. Type I: Impression Plaster original impression material rigid, fractures and breaks easily used for edentulous models Ratio: 60 ml water : 100 gm powder

  5. Type II: Lab Plaster/Model Plaster • Slightly stronger than Type I • Used for: diagnostic casts or study models • Used to fabricate bleach trays, night guards, sports mouth guards • Used in treatment planning, measuring dentition, legal record of, comparison of before and after treatment • Ratio: 50 ml water : 100 gm powder

  6. Type III: Lab Stone • Stronger than plaster • Normally yellow (“buff”) • Used for: study models, working casts, models for partial and full dentures • Ratio: 30 ml water : 100 gm powder

  7. Orthodontic Stone • White • Used for: diagnosis and treatment of orthodontic cases • Ratio: 30 ml of water : 100 gm powder

  8. Type IV: Die Stone • Positive replica of prepared tooth • Strong and resistant to abrasion • Most accuracy and detail • Used for: dies and where strong model is needed in casting metals or making crowns • Ratio: • 24 ml water : 100 grams powder

  9. Type V: High-strength Die Stone • High strength and high expansion • Recently added by the ADA • Strongest accepted gypsum product • Ratio: 18-22 ml water : 100 gms powder

  10. Water : Powder Ratio • Less water • Shortens setting time; dry and crumbly • More water • Thin mixture; weaker product with air bubbles • After mix starts: adding water to thin or powder to thicken =weakens final product • Increasing water temperature = faster set with no affect on quality of final product

  11. Armamentarium • Flexible rubber bowl • Stiff narrow spatula • Water measuring device • Scale • Model vibrator, with protective covering • Room temperature water

  12. Mixing Process (hydration) • Add powder to water; let it dissolve into water • Slowly mix particles with spatula (20 seconds) • Add powder to desired creamy, putty-like thickness (peanut butter) (1 minute) • Material will stick to spatula when lifted from bowl, when it is proper thickness • Vibrate to remove air bubbles (1 minute)

  13. Mixing Techniques Using vibrator to remove air bubbles Checking for proper thickness

  14. Caution re: mixing • DO NOT WHIP: will add air and bubbles • DO NOT OVERMIX: will add weak spots to model

  15. Setting Process (dihydration) • Exothermic reaction (release of heat) drives off water to harden gypsum material • Material will heat up and then cool down

  16. Setting Time (40 – 60 minutes) • Initial Set: • Time between start of spatulation until material loses gloss • Firm and solid enough to handle • Still moist and pliable (cold and wet) • Final Set: • After all heat is driven away • Cool, hard and dry

  17. Factors Affecting Setting Time • Type of gypsum powder • Water and air temperature • Water : powder ratio • Addition of • Retardants (slow down = cold water) • Accelerators (speed up) = warm water OR • SLURRY (mix of watery trimmed plaster residue)

  18. Microbes • Microbes can live within gypsum for 7 days • PPE very important!

More Related