1 / 55

Lecture 15

Lecture 15. Microarchitecture Level: Level 1. Microarchitecture Level. The level above digital logic level. Job: to implement the ISA level above it. The design depends on: ISA being implemented Cost Performance goal. Microarchitecture Level.

lois
Download Presentation

Lecture 15

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Lecture 15 Microarchitecture Level: Level 1

  2. Microarchitecture Level • The level above digital logic level. • Job: to implement the ISA level above it. • The design depends on: • ISA being implemented • Cost • Performance goal

  3. Microarchitecture Level • Many modern ISAs, e.g. RISC, have simple instructions that can usually be executed in a single clock cycle. • Other complex ISAs, e.g. Pentium IV, may require many clock cycles to execute single instruction.

  4. Basic Elements of Processor • ALU • Registers • Internal data paths • External data paths • Control Unit

  5. Types of Micro-operation • Transfer data between registers • Transfer data from register to external • Transfer data from external to register • Perform arithmetic or logical operations

  6. Functions of Control Unit • Sequencing • Causing the CPU to step through a series of micro-operations • Execution • The CU causes each micro-op to be performed. • This is done using Control Signals

  7. Control Signals • Clock • One micro-instruction (or set of parallel micro-instructions) per clock cycle • Instruction register • Op-code for current instruction • Determines which micro-instructions are performed • Flags • State of CPU • Results of previous operations • From control bus • Interrupts • Acknowledgements

  8. Model of Control Unit

  9. Control Signals - output • Within CPU • Cause data movement • Activate specific functions • Via control bus • To memory • To I/O modules

  10. Example Control Signal Sequence - Fetch • MAR <- (PC) • Control unit activates signal to open gates between PC and MAR • MBR <- (memory) • Open gates between MAR and address bus • Memory read control signal • Open gates between data bus and MBR

  11. Example: Data Paths and Control Signals

  12. Internal Organization • Usually a single internal bus • Gates control movement of data onto and off the bus • Control signals control data transfer to and from external systems bus • Temporary registers needed for proper operation of ALU

  13. Microprogrammed Control • A microprogram has a sequence of instructions in a microprogramming language. • These are very simple instructions that specify micro-operations.

  14. Microprogrammed Control • A microprogrammed control unit is a simple logic circuit that is capable of: • Sequencing through microinstructions • Generating control signals to execute each microinstruction. • As in a hardwired control unit, the control signal generated by a microinstruction are used to cause register transfers and ALU operations.

  15. Control Unit Organization

  16. Micro-programmed Control • Use sequences of instructions to control complex operations. • Called micro-programming or firmware

  17. Micro-programmed Control • All the control unit does is generate a set of control signals. • Each control signal is on or off. • Represent each control signal by a bit. • Have a control word for each micro-operation. • Have a sequence of control words for each machine code instruction. • Add an address to specify the next micro-instruction, depending on conditions.

  18. Micro-programmed Control • Today’s large microprocessor • Many instructions and associated register-level hardware • Many control points to be manipulated • This results in control memory that • Contains a large number of words • co-responding to the number of instructions to be executed • Has a wide word width • Due to the large number of control points to be manipulated

  19. Micro-program Word Length • Based on 3 factors • Maximum number of simultaneous micro-operations supported • The way control information is represented or encoded • The way in which the next micro-instruction address is specified

  20. Micro-instruction Types • Each micro-instruction specifies single (or few) micro-operations to be performed • (vertical micro-programming) • Each micro-instruction specifies many different micro-operations to be performed in parallel • (horizontal micro-programming)

  21. Vertical Micro-programming • Width is narrow • n control signals encoded into log2 n bits • Limited ability to express parallelism • Considerable encoding of control information requires external memory word decoder to identify the exact control line being manipulated

  22. Horizontal Micro-programming • Wide memory word • High degree of parallel operations possible • Little encoding of control information

  23. Typical Microinstruction Formats

  24. Compromise • Divide control signals into disjoint groups • Implement each group as separate field in memory word • Supports reasonable levels of parallelism without too much complexity

  25. Organization ofControl Memory

  26. Control Unit Store a set of microinstructions For vertical microinstructions only

  27. Control Unit Function • Sequence logic unit issues read command • Word specified in control address register is read (from control memory) into control buffer register • Control buffer register contents generates control signals and next address information • Sequence logic loads new address into control address register based on next address information from control buffer register and ALU flags

  28. Next Address Decision • Depending on ALU flags and control buffer register • Get next instruction • Add 1 to control address register • Jump to new routine based on jump microinstruction • Load address field of control buffer register into control address register • Jump to machine instruction routine • Load control address register based on opcode in IR

  29. Advantages and Disadvantages of Microprogramming • Advantage: • Simplifies design of control unit • Cheaper • Less error-prone • Disadvantage: • Slower Microprogramming is the dominant technique for implementing control unit in pure CISC.

  30. Hard Wired Control Unit • Disadvantage: • Complex sequencing & micro-operation logic • Difficult to design and test • Inflexible design • Difficult to add new instructions • Advantage: • Faster Hardwired control unit is typically use for implementing control unit in pure RISC.

  31. Tasks Done By Microprogrammed Control Unit • Microinstruction sequencing • Microinstruction execution • Must consider both together

  32. Design Considerations • Size of microinstructions • Address generation time • Determined by instruction register • Once per cycle, after instruction is fetched • Next sequential address • Common in most designed • Branches • Both conditional and unconditional

  33. Sequencing Techniques • Based on current microinstruction, condition flags, contents of IR, control memory address must be generated. • Based on format of address information • Two address fields • Single address field • Variable format

  34. Branch Control Logic: Two Address Fields

  35. Branch ControlLogic: Single Address Field

  36. Branch Control Logic: Variable Format

  37. Execution • The cycle is the basic event • Each cycle is made up of two events • Fetch • Determined by generation of microinstruction address • Execute • Effect is to generate control signals • Some control points internal to processor • Rest go to external control bus or other interface

  38. Control Unit Organization

  39. A Taxonomy of Microinstructions • Classification of microinstruction: • Vertical/horizontal • Packed/unpacked • Hard/soft microprogramming • Direct/indirect encoding

  40. How to Encode • K different internal and external control signals • Wilkes’s (first proposed the use of microprogrammed control unit in 1951): • K bits dedicated • 2K possible combination of control signals. • Not all used • Two sources cannot be gated to same destination • Register cannot be source and destination • Only one pattern presented to ALU at a time • Only one pattern presented to external control bus at a time.

  41. How to Encode • Require Q < 2K which can be encoded with log2Q < K bits • Not done • As difficult to program as pure decoded (Wilkes) scheme. • It is complex and therefore slow control logic module. • Compromises • More bits than necessary are used. • Some combinations that are physically allowable are not possible to encode.

  42. Microinstruction Encoding • In practice, microprogrammed control units are not designed using: • a pure unencoded or • horizontal microinstruction format. • At least some degree of encoding is used to reduce control memory width and to simplify the task of microprogramming.

  43. Specific Encoding Techniques • Microinstruction organized as set of fields • Each field contains code • Activates one or more control signals • Organize format into independent fields • Field depicts set of actions (pattern of control signals) • Actions from different fields can occur simultaneously • Alternative actions that can be specified by a field are mutually exclusive • Only one action specified for field could occur at a time

  44. Microinstruction EncodingDirect Encoding

  45. Microinstruction EncodingIndirect Encoding

  46. The Data Path: Example The data path is the part of CPU containing ALU, its input and its output. Mic-1

  47. The Data Path: Example( cont…) Useful combinations of ALU signals and the function performed. ALU functions is determined by the 6 control lines.

  48. Microinstruction Control: The Mic-1 • To control the datapath of Mic-1, we need 29 signals: • 9 signal to control writing data from the C bus into registers. • 9 signal to control enabling registers onto the B bus for ALU i/p. • 8 signal to control the ALU and shifter functions. • 2 signal (not shown) to indicate memory read/write via MAR/MDR. • 1 signal (not shown) to indicate memory fetch via PC/MBR.

  49. Microinstruction Control: The Mic-1 • The values of 29 control signals specify the operations for one cycle of the data path. • A data path consists of: • Gating values out of registers and onto the B bus. • Propagating the signals through the ALU and shifter. • Driving them onto the C-bus. • Writing the results in the appropriate register(s). • In addition, if a memory read data signal is asserted, the memory operation is started at the end of the data cycle, after MAR has been loaded.

  50. We use 9+4+8+2+1=24 signals to control data path for one cycle. Microinstruction Control: The Mic-1 • Issues: • It may be desirable to write the o/p on the C bus into many registers. • It is never desirable to enable more than one register write onto the B bus at a time – physical damage. By adding a 4-to-16 decoder, we can reduce the number of bits needed to select among the possible sources for driving the B bus. How to determine the next cycle? Need 2 additional fields: • NEXT_ADDRESS field • JAM field.

More Related