1 / 54

USCG AIRSTA MIAMI EPIRB’s How They Work & DF-430 MH-65C & D, MH60T, HU25, C-130J, HC144

USCG AIRSTA MIAMI EPIRB’s How They Work & DF-430 MH-65C & D, MH60T, HU25, C-130J, HC144. January 2010. How the System Works. LEOSAR & GEOSAR Satellites. Types of Beacons. Maritime Distress Beacon. EPIRB s 406 MHz (w/ 121.5 homer) Automatic activation when out of bracket and wet.

liana
Download Presentation

USCG AIRSTA MIAMI EPIRB’s How They Work & DF-430 MH-65C & D, MH60T, HU25, C-130J, HC144

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. USCG AIRSTA MIAMIEPIRB’sHow They Work&DF-430MH-65C & D, MH60T, HU25, C-130J, HC144 January 2010

  2. How the System Works L.T.Yarbrough/D7 CFVS

  3. LEOSAR & GEOSAR Satellites L.T.Yarbrough/D7 CFVS

  4. Types of Beacons Maritime Distress Beacon • EPIRBs 406 MHz (w/ 121.5 homer) Automatic activation when out of bracket and wet. Floats upright to transmit Strobe light Min 48 hour transmit Some GPS enabled L.T.Yarbrough/D7 CFVS

  5. Types of Beacons Distress Beacon for Personal Use (Land Rescue) • PLBs 406 MHz (w/ 121.5 homer) Manual activation Carried on persons May or may not float Held out of water to transmit NO Strobe light required Min 24 hour transmit Some GPS Enabled L Yarbrough/D7 CFVS

  6. Types of Beacons Aviation Distress Beacon • ELTs Transmit on 121.5 (most) or 406 MHz Integrated 121.5 MHzhomer Crash activation Floats upright to transmit No Strobe light Min 48 hour transmit L Yarbrough/D7 CFVS

  7. EPIRB • Maritime Satellite • Emergency • Position-Indicating • RadioBeacon L.T.Yarbrough/D7 CFVS

  8. EPIRB Operational Requirements • EPIRB 406 MHz Signal - 5 Watts • Short bursts at approximately 50 second intervals (varies between 47.5 and 52.5 s), with a transmission time of 440 ms or 520 ms. • Transmits in the 406.0 to 406.1 MHz band. • Transmission consists: • unmodulated carrier, for 160 ms, • short synchronization signal, signal inverted for test, • Digital message that provides stored information (identification, nationality, type of user), • Optionally, current information like, type of emergency and estimated location. Designed to prevent inadvertent activation L.T.Yarbrough/D7 CFVS

  9. Hex ID • EPIRB’s identification, when decoded into its 15 character hexadecimal representation, which is the EPIRB’s unique identifier number. • http://www.cospas-sarsat.org/Beacons/decode.htm • Normally readout in 3 groups of 5 characters. Example: ABCDE 12345 ABCDE L.T.Yarbrough/D7 CFVS

  10. Battery Replacement • Required at Expiration date or if EPIRB activated for any reason besides test. • Useful Life = power for all required testing + 48 hrs operation. L.T.Yarbrough/D7 CFVS

  11. EPIRB Operational Requirements • Positive visual and/or audible indication that EPIRB is activated (strobe light flashing). • Easily manually deployed, activate, and deactivated, and transferred to survival craft. • Not be activated or deactivated by conditions encountered in maritime environment. L.T.Yarbrough/D7 CFVS

  12. EPIRB Control • Ready – EPIRB should be ON in the water unless in its bracket. Sometimes labeled “OFF”. • ON – EPIRB operates regardless of location or orientation. Unconditional “ON” position. (Requires two physical actions) • Test – Self-test Function. L.T.Yarbrough/D7 CFVS

  13. Prevention of Inadvertent Activation • Must be fitted with means to prevent inadvertent activation and deactivation. • Not automatically activate when water washes over while in bracket. • Most EPIRBs use bracket with magnet to disable activation circuit. L.T.Yarbrough/D7 CFVS

  14. EPIRB Deactivation • Remove beacon from water and dry off or replace in bracket • Move switch to OFF or Ready position • If the above failed then: • Remove cover and disconnect battery L.T.Yarbrough/D7 CFVS

  15. EPIRB Activation • How • By definition it transmits: • out of bracket and wet, • by manual switch, in or out of bracket, Or • Self test L.T.Yarbrough/D7 CFVS

  16. EPIRB Activation • What Happens; • Beacon starts transmitting its Unique Hex ID in a 406 MHz digital message, • 121.5 MHz homer with an audible warble, • Strobe Light starts flashing. L.T.Yarbrough/D7 CFVS

  17. Rockwell Collins DF-430 L.T.Yarbrough/D7 CFVS

  18. NAV Page • LS3 access the DF Control Page. • Accesses the NAV Page. L.T.Yarbrough/D7 CFVS

  19. DF Control Page • Access to BCN, TAC, and SAR pages. • Display page for LAT/Long if received.  PRESETS Df ctrl MODE: ON BCN  TAC SAR C/S ------------------------------------ ↕[] L.T.Yarbrough/D7 CFVS

  20. DF-430 Utilization by USCG Aircraft • DF-430 Modes: Despite aircraft unique installations, all interfaces provide 3 basic modes of operations: • TAC SCAN - Tactical Scan • SAR SCAN - SAR • BCN - Beacon L.T.Yarbrough/D7 CFVS

  21. TAC Scan • TAC Scan - will scan: 121.5 MHz, 243.0 MHz, 406 (.025 / .028 / .037) MHz, + Manually entered frequency. • Signal detection on operator selected tac freq, will result in TAC DET annunciation + bearing pointer. • 406, 121, or 243 detection will get DET annunciation, No bearing pointer. L.T.Yarbrough/D7 CFVS

  22. SAR Scan • SAR Scan - will scan: 121.5 MHz, 243.0 MHz, and 406 (.025 / .028 / .037) MHz, with priority to 406 MHz. • Signal detection 406, will result in DET annunciation + bearing pointer. • 121, or 243 detection will get DET annunciation, No bearing pointer. L.T.Yarbrough/D7 CFVS

  23. BCN • Beacon provides single-channel access to one of six signals: 121.5, 243.0, 406 MHz, CH=16 (156.800MHz), CH-70 (156.525 MHz), or ARGOS (401.650 MHz). • ARGOS (401.650) is the frequency for your SLDMB. L.T.Yarbrough/D7 CFVS

  24. Embedded GPS Data • Only some Beacons have GPS • Data only viewable if the aircraft DF-430 on the DF Control Page. • GPS data should be considered confirming source. • Fly the Needle on your DF bearing pointer. L.T.Yarbrough/D7 CFVS

  25. DF Control Page • C/S Will display LAT/LONG when position transmitting capable 406 is detected. LS4s will then copy position into scratchpad.  PRESETS Df ctrl MODE: ON BCN  TAC SAR C/S ------------------------------------ ↕[] L.T.Yarbrough/D7 CFVS

  26. “fly-to-waypoint”. • From the DF Control Page, the aircrew will be able to capture GPS data into their scratchpad and create a “fly-to-waypoint”. • This can assist: • if the EPIRB signal is lost, or • at EPRIB passage as the FMS needle may swing before the DF needle due to ~50 sec transmit cycle of beacon. L.T.Yarbrough/D7 CFVS

  27. DF Bearing Pointer • DF pointer is relative (not stablilized) • DF pointer only updates on receipt of next 406 MHz EPIRB burst transmission. • Will seem jerky. • EPIRB transmission only every ~50 sec. • Burst transmission only half sec duration. L.T.Yarbrough/D7 CFVS

  28. Figure-of-Merit (FOM) Values • DF-430 will display a FOM value in range of 0-255. Only displays on TAC, SAR, or BCN Scan Page. • Practical application is as a secondary level of confidence the aircraft is tracking towards target. L.T.Yarbrough/D7 CFVS

  29. 406 MHz Detection Range L.T.Yarbrough/D7 CFVS

  30. Operational Considerations • Transit in SAR Scan, unless tasking indicates a need to monitor a tactical freq. • Greatest range/ earliest detection opportunity at higher altitudes. • If a 406 signal is detected, DF needle will point and the GPS position displayed when received. L.T.Yarbrough/D7 CFVS

  31. 406 Beacon Tests • Every 406 MHz Beacon is supposed to be tested (using the self-test function) once every month. • Each test transmits one live 406 burst. • Wait at least two bursts before you react to a 406 Det. L.T.Yarbrough/D7 CFVS

  32. Operational Considerations • GPS positions from EPIRBs have been inaccurate. If the FMS and DF needles split, wait for next 406 burst and then Follow the DF Needle. • As a second confirming indication, watch for increasing FOM. L.T.Yarbrough/D7 CFVS

  33. EPIRB Prosecution What Does the CC/RCC do with a 406 Alert? L.T.Yarbrough/D7 CFVS

  34. Registered/Unlocated 406MHZ EPIRB • 1. RCC or RSC on receipt of unlocated registered 406 EPIRB: • a. Place case in the DISTRESS phase. • b. Assume SMC. • c. Determine status of vessel from contact number listed, available databases, etc. L.T.Yarbrough/D7 CFVS

  35. Registered/Unlocated 406MHZ EPIRB (cont) • 2. If vessel is determined to be safe underway or in port: • a. Close case. A case will be claimed for all 406 alerts prosecuted L.T.Yarbrough/D7 CFVS

  36. Registered/Unlocated 406MHZ EPIRB (cont) • 3. If vessel is underway and cannot be contacted: • a. Issue UMIB for Home Port and general area in which vessel is believed to be operating. • b. Contact AMVER Ships and request callouts for the vessel. • c. Contact USMCC and request satellite forecast for the geographic area. L.T.Yarbrough/D7 CFVS

  37. Registered/Unlocated 406MHZ EPIRB (cont) • 3. If vessel is underway and cannot be contacted: • d. If the next forecast satellite pass does not locate the beacon consider sending an SRU to the area to attempt to hail the vessel or DF on 406/121.5MHZ homing signal. Continue investigating to try to determine last known position/probable track of vessel for additional searches. L.T.Yarbrough/D7 CFVS

  38. Registered/Unlocated 406MHZ EPIRB (cont) • 3. If vessel is underway and cannot be contacted: • e. If vessel cannot be located after reasonable search is conducted, search will be suspended. L.T.Yarbrough/D7 CFVS

  39. Registered/Unlocated 406MHZ EPIRB (cont) • 4. If SRU is tasked to search for vessel: • a. Proceed top LKP/tasked search area. Make callouts for vessel and attempt to DF homing beacon on 406/121.5MHZ. L.T.Yarbrough/D7 CFVS

  40. Registered/Unlocated 406MHZ EPIRB (cont) • 4. If SRU is tasked to search for vessel: • b. If signal cannot be DF’d once on scene and unless otherwise tasked, aircraft shall complete a VS search at radius of 12NM. Vessels shall complete the same search at 3NM. L.T.Yarbrough/D7 CFVS

  41. “A” solution located 406MHZ EPIRB • 1. RCC or RSC on receipt “A” solution located 406MHZ EPIRB: • a. Place case in the DISTRESS phase. • b. Assumed SMC. • c. Determine status of vessel from contact number listed (if registered), available databases, etc. L.T.Yarbrough/D7 CFVS

  42. “A” solution located 406MHZ EPIRB (cont) • 2. RCC or RSC if vessel is determined to be safe/underway or in port: • a. Close case. L.T.Yarbrough/D7 CFVS

  43. “A” solution located 406MHZ EPIRB (cont) • 3. RCC or RSC if vessel is underway and cannot be contacted: • a. Issue UMIB for general area in which vessel is believed to be operating. • b. Contact AMVER ships in vicinity and request callouts for vessel. • c. Dispatch SRU to located vessel and determine status. SRU’s should be tasked to DF on the signal. L.T.Yarbrough/D7 CFVS

  44. “A” solution located 406MHZ EPIRB (cont) • 3. RCC or RSC if vessel is underway and cannot be contacted: • d. If vessel cannot be located after reasonable search is conducted, search will be suspended. L.T.Yarbrough/D7 CFVS

  45. “A” solution located 406MHZ EPIRB (cont) • 4. SRU if tasked to search for vessel: • a. Proceed to position/tasked search area. Make callouts for vessel and attempt to DF homing beacon on 406/121.5MHZ. • b. If a signal cannot be DF’d once on scene and unless otherwise tasked, aircraft shall complete a VS search at radius of 12NM. Vessels shall complete the same search at 3NM. L.T.Yarbrough/D7 CFVS

  46. “B” solution with alert probability less than or equal to 20% 1. RCC or RSC on receipt “B” solution with probability less than or equal to 20%: • Place case in the UNCERTAINTY phase. • Assume SMC. • Coordinate investigation with RCC responsible for “A” solution. If investigation determines “B” solution is the likely position, respond in same manner as an “A” solution. L.T.Yarbrough/D7 CFVS

  47. “B” solution with alert probability greater than 20% • 1. RCC or RSC on receipt “B” solution with probability greater than 20%: • a. Place case in the ALERT phase. • b. Assumed SMC. • c. Coordinate investigation with RCC responsible for “A” solution. If investigation determines “B” solution is the likely position, respond in same manner as an “A” solution. L.T.Yarbrough/D7 CFVS

  48. Unregistered/Unlocated EPIRB alerts: • 1. RCC or RSC investigate identity of vessel through vessel data bases. • 2. RCC or RSC contact RCC country of vessel registered and attempt to determine vessel’s status. L.T.Yarbrough/D7 CFVS

  49. False Alerts L.T.Yarbrough/D7 CFVS

  50. False Alerts • If a false alert is determined upon arrival on-scene complete the following actions: • Have vessel de-activate the beacon. • Have vessel provide the beacon “HexID” • Have vessel provide the reason beacon alerted and include in MISLE Reporting. • Advise vessel that EPIRB and bracket require servicing and battery replacement. • Relay to tasking authority as required. L.T.Yarbrough/D7 CFVS

More Related