1 / 64

Noise in Modulation

Noise in Modulation. The primary figure of merit for signals in analog systems is signal-to-noise ratio . The signal-to-noise ratio is the ratio of the signal power to the noise power.

Download Presentation

Noise in Modulation

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Noise in Modulation

  2. The primary figure of merit for signals in analog systems is signal-to-noise ratio. The signal-to-noise ratio is the ratio of the signal power to the noise power. While the amount of external ambient noise is not always within the control of a communications engineer, the way in which we can distinguish between the signal an the noise is. The demodulation process for any modulation system seeks to recreate the original modulating signal with as little attenuation of the signal and as much attenuation of the noise as possible.

  3. The signal-to-noise ratio changes as the modulated signal goes through the demodulation process. We wish the signal-to-noise ratio to increase as a result of the demodulation process. The extent to which the signal-to-noise ratio increases is called the signal-to-noise improvement, or SNRI. This signal-to-noise improvement is equal to the ratio of the demodulated signal-to-noise ratio to the input signal-to-noise ratio.

  4. The calculation of the signal-to-noise improvement (SNRI) is shown in the following diagram. si(t) si(t) Demodulator ni(t) no(t)

  5. The notation < > means time average.

  6. In determining the ability of a demodulator to discriminate signal from noise, we calculate Psi, Pso, Pni and Pno and plug these values (or expressions) into the expression

  7. Noise in Amplitude Modulated Systems • The SNRI will be calculated for DSB-SC and DSB-LC. • A DSB-SC demodulator is linear: the signal and the noise components can be considered separately. • A DSB-LC demodulator is non-linear: the signal and the noise components cannot be treated separately.

  8. The expression for the modulated carrier for DSB-SC is Demodulation of this signal is performed by multiplying xc(t) by cos wct and low-pass filtering the result. d(t) LPF X si(t) = xc(t) so(t) coswct

  9. The result of this demodulation can be seen by analysis: Low-pass filtering the result eliminates the cos 2wct component.

  10. Based upon these relationships, we can find the ratio of the signal input power and the signal output power.

  11. So, it seems, half of our SNRIcalculation is done.

  12. The other half of the calculation deals with the noise. Let us use the quadrature decomposition to represent the noise: It is this signal which will represent ni(t).

  13. The noise input to the demodulator (in the above form) is demodulated along with the signal. Because the demodulator is linear, we can treat the noise separately from the signal. ni(t) = nccoswct – nssinwct dn(t) LPF X no(t) coswct

  14. After dn(t) passes through the low-pass filter, all we have left is

  15. Now, we calculate the power in the noise.

  16. The ratio of the noise powers becomes Finally, our signal-to-noise improvement becomes

  17. Thus, the DSB-SC demodulation process improvesthe signal-to-noise ratio by a factor of two.

  18. The expression for the modulated carrier for DSB-LC is (This is a simplified version of the more accurate expression which takes into account the modulation index. In this simplified version, the modulation index is equal to one.) The demodulation process extracts m(t) from xc(t).

  19. The input signal power is

  20. The modulating signal m(t) is assumed here to have zero mean. If m(t) = coswmt, then

  21. The output power is simply which is equal to ½ if m(t) = coswmt. Thus, when m(t) is a sinewave, our signal power ratio is

  22. Now, we deal with the noise. As mentioned previously, since the demodulation process is non-linear, we cannot treat the signal and the noise separately. To deal with the noise, we retain the carrier, but set the modulating signal to zero. Thus, the signal that we demodulate is

  23. The resultant output from demodulating this signal will be the output noise power. To demodulate this signal (analytically), we use the quadrature decomposition for n(t). The input to our demodulator becomes

  24. We then work with this expression: At this point we make an assumption (which turns out to be quite reasonable in many cases):

  25. In words, the noise (either the in-phase or quadrature component) is much smaller in magnitude that that of the signal coswct. With this assumption the input to the demodulator becomes

  26. We recall that when the input is applied, the output is

  27. Similarly, when the input is is applied, the output is

  28. Thus, the noise output is The output noise power is

  29. Thus, and

  30. We see that the signal-to-noise improvement for DSB-LC is not as good as that of DSB-SC. The reason for using DSB-LC is that it is relatively easy to demodulate. (Standard broadcast AM [530-1640 kHz], uses DSB-LC.)

  31. Noise in Frequency Modulated Systems • The frequency modulation and demodulation process is non-linear. • As with DSB-LC, we cannot treat the signal and the noise separately.

  32. The expression for the modulated carrier for FM As with DSB-LC AM, he demodulation process extracts m(t) from xc(t). This extraction process consists of three steps:

  33. Extract argument from cos(). • Subtract wct. • Differentiate what is left to get kfm(t). Based upon these three steps we can quickly get the input signal power and the output signal power.

  34. Without much loss of generality, we can assume that m(t) = coswmt.

  35. We now have the signal power ratio:

  36. As with the DSB-LC AM, the effective noise input comes along with an unmodulated carrier: If use the quadrature decomposition of the noise, we have, as the effective noise input

  37. or, This expression can be combined into a single sinewave

  38. where At this point we make a simliar assumption to what we made with DSB-LC AM:

  39. (The new part is the 1.) Using this assumption we have (This last is true because tan-1 x  x for small values of x.)

  40. With the assumptions given, our effective noise input becomes We may now apply our three demodulation steps: • Extract argument from cos(). • Subtract wct. • Differentiate what is left to get kfm(t).

  41. 1. 2. 3.

  42. Thus, the output noise is All that remains to be done is to find the noise power from the noise signals [ni(t) and no(t)]. The noise power will be found from the power spectral densities of the input noise and the output noise.

  43. The input noise is additive white Gaussian noise. The power spectral density of the input noise is The output noise is the derivative of the quadrature component of the (input) noise [ns(t)].

  44. We know, from a previous exercise, that We need to find the power spectral density of the derivative of the quadrature component. To find this we multiply Sns(f) by the square of the transfer function for the differentiation operation.

  45. The effect of the differentiation operation is shown in three ways: d dt . ns(t) ns(t) j2pf Ns(f) No(f) |2pf|2 Sns(f) Sno(f)

  46. Thus, the power spectral density of the output noise is Now that we have the power spectral densities of the input and the output spectra, all that remains to find the power is to integrate the respective power spectral densities over the appropriate frequencies.

  47. The input noise is a bandpass process. Let BT be the bandwidth. Sni(f) N0/2 f BT

  48. Integrating the power spectral density, we have

  49. The input noise is a lowpass process. Let W be the bandwidth. Sno(f)=N04p2f2 f -W W

  50. Integrating the power spectral density, we have

More Related