1 / 11

How to Recover Password for a Cisco 3925 Router

This slide provide you some easy tips.<br>Here are the basic steps you need to know if you are planning on changing the router's password.If you found any issue contact Cisco Router tech support Number (61) 386580446

laylakirk
Download Presentation

How to Recover Password for a Cisco 3925 Router

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Password Recovery for a Cisco 3925 Router

  2. The Cisco 3925 router plays an important role in networking equipment produced by Cisco, which has been a network equipment giant for many years. Used 3925 routers are available on the Internet at reasonable prices, so acquiring one is not so difficult. However, if you’re Cisco 3925 Router password will be lost or forget by you then reconfiguration become impossible until it will not reset or recovered. For facing such difficulty, Cisco has built in a procedure for rescuing lost or forgotten passwords or entering new passwords by providing the following steps. Moreover, we also provide these instructions on Cisco support phone number, through our talented technical experts. You will require Serial to RJ-45 cable and Terminal emulation software

  3. Step1 Connect your computer to the router with the blue serial-to-RJ-45 cable that came with the router. The 9-pin D-shell end connects to your computer's serial port, while the RJ-45 end connects to the console jack on the router. The RJ-45 end resembles a slightly larger telephone jack connector.

  4. Step2 Turn on your computer and establish a terminal session to the 3925. You can use any terminal emulator and many are freely available on the Internet. Configure the session settings as follows: • 9600 baud • 8 data bits • No parity • 1 stop bit • No flow control

  5. Step3 Plug the router's power cables into an electrical outlet and as the 3925 boots, you should see the Cisco boot messages. If you don't see any output on your computer's terminal session, check your settings on the session and restart it if necessary. Press "Break" within 30 seconds of powering on the router to enter rommon (ROM monitor) mode.

  6. Step4 Type "confreg 0x2142" and press "Enter" at the "rommon 1>" prompt. This will cause the router to boot from its internal flash memory without loading the configuration into memory. At the following "rommon 2>" prompt, type "reset" and press "Enter." This will cause the router to reload and ignore the previously saved configuration file.

  7. Step5 Respond "no" and press "Enter" when prompted for responses to enter the initial dialog or basic management setup. Type "enable" and press "Enter" at the following "Router>" prompt. This will put you into enable mode and display the "Router#" prompt. Copy the non-volatile memory into memory with the "copy startup-config running-config" command, followed by the "Enter" key. Type "sho run" at the prompt and press "Enter" to display the current configuration, including the passwords, some of which may be encrypted.

  8. Step6 Type "config t" at the prompt and press "Enter." At the "Router(config)#" prompt, type "enable secret <pswd>" -- where "pswd" is the password -- and press "Enter." At this point, your enable password is reset. Press "Ctrl" + "z" to return to the "Router#" prompt.

  9. Step7 Type "config t" at the "Router#" prompt and press "Enter." At the "Router(config)#" prompt, type "config-register 0x02102" and press "Enter" to reset the boot register to its normal setting. Press "Ctrl" + "z" to leave configuration mode. Type "copy running-config startup-config" and press "Enter" to save your changes. Reboot the router and you should be able to login with your password.

  10. You can also Contact Cisco Router Tech Support for any kind of online assistance.

  11. Contact Us Cisco Router Tech support Number +(61) 386580446 Original source: http://geekswithblogs.net/CiscoRouterhelpline/archive/2016/10/26/199749.aspx

More Related