1 / 14

Object Sensing using 802.11ad devices

Object Sensing using 802.11ad devices. Date: 2010-09-15. Authors:. Abstract. The hardware of an 802.11ad device is very similar to that of a powerful short-range radar could be used to sense objects in local vicinity of device estimate position and movement of objects

Download Presentation

Object Sensing using 802.11ad devices

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Object Sensing using 802.11ad devices Date: 2010-09-15 Authors: Thomas Derham, Orange Labs

  2. Abstract • The hardware of an 802.11ad device is very similar to that ofa powerful short-range radar • could be used to sense objects in local vicinity of device • estimate position and movement of objects • A “dual-mode” device (communications + object sensing) wouldmake for a low-cost implementation with various applications • smart home/environment, security sensing, … • collision avoidance, emergency detection of humans, … • coexistence with 11ad communications can be ensured • schedule self-allocated SPs for object sensing to prevent interference • efficient method to minimize effect on network efficiency Thomas Derham, Orange Labs

  3. Using 802.11ad device as a radar • Merits: • Baseband bandwidth: 2 GHz => range resolution: 7.5 cm • Array antenna beamwidth: 23 deg (6x6) => angular resolution: 0.8 m @ 2m range • High Doppler / micro-Doppler sensitivity due to small wavelength (5 mm) • Demerits: • limited dynamic range (ADC/DAC ENOB) - may need tight AGC control • fast Tx/Rx antenna switch may be required in case of shared antenna Thomas Derham, Orange Labs

  4. Basic operation • Pulse Doppler radar: • (1) Tx generates and transmits pre-defined radar pulses at pre-defined times • (2) Rx coherently receives reflections of these pulses from nearby objects • (3) Joint signal processing of all received pulses • (4) Repeat for different antenna beam directions to form 4D radar image • range, azimuth, elevation, radial velocity Thomas Derham, Orange Labs

  5. Information in Radar Image • Radar image is 4D array of effective complex reflectivity values • Dimensions: range, azimuth, elevation, radial velocity • From radar image, presence of objects can be detected • Position estimation • range, azimuth, elevation • Movement estimation • linear radial velocity • from conventional Doppler effect – linear movement gives rise to single “spike” in velocity dimension • vibration frequency • from Micro-Doppler effect – vibration causes series of “spikes” in velocity dimension (Bessel weighted), spaced by the vibration frequency Thomas Derham, Orange Labs

  6. Applications • Example capabilities • create 3D image of objects in vicinity • estimate distance to nearest object (e.g. on current trajectory) • identify presence of human in vicinity (breathing / heart beat micro-Doppler) • identify activity of human e.g. waving arms (micro-Doppler gait analysis) • Example applications (opportunistic or non-opportunistic) • Smart Environment • determine and predict location of individual, … • Vehicle/robot collision avoidance • Security sensing • Emergency detection of humans in earthquake (battery backup) Thomas Derham, Orange Labs

  7. Structure of transmission/reception bursts of pulses – objects are approximately static over each burst if Tx/Rx antenna switch • pulse length: • pulse transmission must (or preferably should) finish before receiver activates • receiver active time: • pulse length + max. propagation time • Burst Repetition Interval: • Nyquist requirement according to max. Doppler frequency • total observation time: • according to required Doppler resolution Thomas Derham, Orange Labs

  8. Structure of transmission/reception (2) bursts at each beam angle are interleaved in time • integration gain: • according to required SNR for radar image • 3 inequalities for required structure: • number of pulses per burst: • number of bursts: Thomas Derham, Orange Labs

  9. Transmitted waveform • transmitted pulse is generally short • spectrum of pulse should be well controlled to: • obtain low range-domain sidelobes • meet spectral mask requirements • e.g. classical chirp (linear FM) waveform • raised cosine time-domain window • range resolution approx. 10 cm • with B = 2 GHz, Thomas Derham, Orange Labs

  10. Signal processing • (1) pulse integration • coherent summation of received pulses in one burst • (2) matched filter • cross-correlation with reference Tx waveform => range profile • (3) Doppler processing • form array comprising values from each range bin (sample of range profile) over all bursts • FFT to form Doppler profile for each range bin • note: phase noise strongly mitigated if common Local Oscillator used forTx and Rx due to “range correlation effect” • (4) combine over all beam directions to form 4D radar image • (5) object detection/classification/identification Thomas Derham, Orange Labs

  11. Coexistence with 11ad communications • device can request self-allocated SPs for object sensing • length and spacing according to the timing of bursts • e.g. using service period requests (SPR) • however, in 11ad cannot request position of SP within a BI • results in irregular time-domain sampling of Doppler • requires interpolation/resampling (sensitive to noise) • therefore, it is preferable that object sensing device is also PCP • can first schedule its own SPs wherever it wants Thomas Derham, Orange Labs

  12. Practical example • min/max range: 3 / 10 m • max Doppler freq: 2 Hz; Doppler resolution: 0.05 Hz (for rapid breathing sensing) • SNR of radar image: 20 dB (at max range) • separate Tx/Rx antennas (no switch required) • pulse length: 20 ns • BRI: 0.25 s • Pulses per burst: 1 • Burst length: 87 ns • Number of bursts: 80 • Total observation time: 20 s • if interleave total of 100 different beam angles, need 87 us SP every 0.25 s • channel overhead for sensing over 20 s period: 0.035% Thomas Derham, Orange Labs

  13. Conclusions • Object sensing capability in 802.11ad devices could provide: • differentiating features (reuse powerful 11ad device hardware) • new potential ecosystem of applications to make 11ad devices even more compelling! • potentially increase market acceptance! • Low implementation complexity • fixed transmitted radar waveforms • DSP may share some logic (e.g. DFT core) with OFDM modulator, … • Coexistence with 11ad communications • efficient use of self-allocated SPs prevent interference within PBSS and minimizes effect on network performance Thomas Derham, Orange Labs

  14. References • [1] B. Lyonnet et al, “Human gait classification using Micro-Doppler time-frequency signal representations”, IEEE Radar Conference 2010 • [2] D. Cook, “Smart Environments: Technology, Protocols and Applications”, Wiley 2004 • [3] IEEE P802.11ad draft amendment D0.1, 2010 • [4] M. Budge, “Range Correlation Effects on Phase and Amplitude Noise”, Southeastcon, 1993 Thomas Derham, Orange Labs

More Related