1 / 29

ELCT564 Spring 2012

ELCT564 Spring 2012. Chapter 5: Impedance Matching and Tuning. Impedance Matching. Maximum power is delivered when the load is matched the line and the power loss in the feed line is minimized. Impedance matching sensitive receiver components improves the signal to noise ratio of the system.

kelly-mccarty
Download Presentation

ELCT564 Spring 2012

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ELCT564 Spring 2012 Chapter 5: Impedance Matching and Tuning ELCT564

  2. Impedance Matching Maximum power is delivered when the load is matched the line and the power loss in the feed line is minimized Impedance matching sensitive receiver components improves the signal to noise ratio of the system Impedance matching in a power distribution network will reduce amplitude and phase errors Complexity Bandwidth Implementation Adjustability ELCT564

  3. Matching with Lumped Elements (L Network) Network for zL outside the 1+jx circle Network for zL inside the 1+jx circle Positive X implies an inductor and negative X implies a capacitor Positive B implies an capacitor and negative B implies a inductor ELCT564

  4. ELCT564

  5. Matching with Lumped Elements (L Network) Smith Chart Solutions Design an L-section matching network to match a series RF load with an impedance zL=200-j100Ω, to a 100 Ω line, at a frequency of 500 MHz. ELCT564

  6. ZL=2-j1 yL=0.4+j0.5 B=0.29 X=1.22 B=-0.69 X=-1.22 ELCT564

  7. Matching with Lumped Elements (L Network) Smith Chart Solutions ELCT564

  8. Single Stub Tunning Shunt Stub G=Y0=1/Z0 Series Stub ELCT564

  9. Single Stub Tunning For a load impedance ZL=60-j80Ω, design two single-stub (short circuit) shunt tunning networks to matching this load to a 50 Ω line. Assuming that the load is matched at 2GHz and that load consists of a resistor and capacitor in series. yL=0.3+j0.4 d1=0.176-0.065=0.110λ d2=0.325-0.065=0.260λ y1=1+j1.47 y2=1-j1.47 l1=0.095λ l1=0.405λ ELCT564

  10. Single Stub Tunning ELCT564

  11. Single Stub Tunning For a load impedance ZL=25-j50Ω, design two single-stub (short circuit) shunt tunning networks to matching this load to a 50 Ω line. yL=0.4+j0.8 d1=0.178-0.115=0.063λ d2=0.325-0.065=0.260λ y1=1+j1.67 y2=1-j1.6 l1=0.09λ l1=0.41λ ELCT564

  12. Single Stub Tunning For a load impedance ZL=100+j80Ω, design single series open-circuit stub tunning networks to matching this load to a 50 Ω line. Assuming that the load is matched at 2GHz and that load consists of a resistor and inductor in series. zL=2+j1.6 d1=0.328-0.208=0.120λ d2=0.5-0.208+0.172=0.463λ z1=1-j1.33 z2=1+j1.33 l1=0.397λ l1=0.103λ ELCT564

  13. Single Stub Tunning ELCT564

  14. Single Stub Tunning ELCT564

  15. Double Stub Tunning The susceptance of the first stub, b1, moves the load admittance to y1, which lies on the rotated 1+jb circle; the amount of rotation is de wavelengths toward the load. Then transforming y1 toward the generator through a length d of line to get point y2, which is on the 1+jb circle. The second stub then adds a susceptance b2. ELCT564

  16. Double Stub Tunning Design a double-stub shunt tuner to match a load impedance ZL=60-j80 Ω to a 50 Ω line. The stubs are to be open-circuited stubs and are spaced λ/8 apart. Assuming that this load consists of a series resistor and capacitor and that the match frequency is 2GHz, plot the reflection coefficient magnitude versus frequency from 1 to 3GHz. yL=0.3+j0.4 b1=1.314 b1’=-0.114 y2=1-j3.38 l1=0.146λ l2=0.204λ l1’=0.482λ l2’=0.350λ y2’ =1+j1.38 ELCT564

  17. Double Stub Tunning ELCT564

  18. Theory of Small Refelections ELCT564

  19. Multisection Transformer Partial reflection coefficients for a multisection matching transformer ELCT564

  20. Binomial Multisection Matching Transformers The passband response of a binomial matching transformer is optimum in the sense, and the response is as flat as possible near the design frequency. Maximally Flat: By setting the first N-1 derivatives of |Г(θ)| to zero at the frequency. ELCT564

  21. Binomial Transformer Design Design a three-section binomial transformer to match a 50Ω load to a 100Ω line, and calculate the bandwidth for Гm=0.05. Plot the reflection coefficient magnitude versus normalized frequency for the exact designs using 1,2,3,4, and 5 sections. ELCT564

  22. Binomial Transformer Design Design a three-section binomial transformer to match a 100Ω load to a 50Ω line, and calculate the bandwidth for Гm=0.05. Plot the reflection coefficient magnitude versus normalized frequency for the exact designs using 1,2,3,4, and 5 sections. ELCT564

  23. Chebyshev Multisection Matching Transformers Chebyshev transformer optimizes bandwidth Chebyshev Polynomials ELCT564

  24. Design of Chebyshev Transformers ELCT564

  25. Design Example of Chebyshev Transformers Design a three-section Chebyshev transformer to match a 100Ω load to a 50Ω line, with Гm=0.05, using the above theory. ELCT564

  26. Design Example of Chebyshev Transformers Design a three-section Chebyshev transformer to match a 100Ω load to a 50Ω line, with Гm=0.05, using the above theory. ELCT564

  27. Tapered Lines ELCT564

  28. Tapered Lines Triangular Taper Klopfenstein Taper ELCT564

  29. Tapered Lines Design a triangular taper, an exponential taper, and a Klopfenstein taper (with Гm=0.05) to match a 50Ω load to a 100Ω line. Plot the impedance variations and resulting reflection coefficient magnitudes versus βL. ELCT564

More Related