1 / 7

Prep for Gain Tests: Some Progress, Some Setbacks

Prep for Gain Tests: Some Progress, Some Setbacks. TKH for the Stony Brook Crew. Box Preparation: Vacuum & Source. Some trouble with mis-manufactured LEMOs: Did not seat flush to surface. Leaked badly.

karina-fuentes
Download Presentation

Prep for Gain Tests: Some Progress, Some Setbacks

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Prep for Gain Tests:Some Progress, Some Setbacks TKH for the Stony Brook Crew

  2. Box Preparation: Vacuum & Source • Some trouble with mis-manufactured LEMOs: • Did not seat flush to surface. • Leaked badly. • ~1/3 of the LEMO connectors did not have full threads up the body…bottomed out before sealing. • Stony Brook Shop Counter-bores holes. • Leaks gone (w/ He leak Checker) • Source mounted using battery clip. • Was 10 mCi 55Fe • Now 2 ½ lives later…

  3. Box Preparation: Pad Plane & Gas • Small mods: • Pad plane initially sized for prototype GEMs • Holes put into it for final sized GEMs • Solder pads interfere with final GEM frames. • Solution: • Solder underside • Raise pad plane. • Done and ready. • Gas/pump: • Done

  4. DAMMIT!!! • On Saturday, while heat-shrinking tubing onto HV divider chain, DISASTER: • Heat Gun and Scroll pump on same breaker. • Breaker trips. • Chamber under vacuum “refills” though pump exhaust line (i.e. from the floor outside of tent) • GEMs/Grid in use have lots of dust on them • “Necessity is the Mother of Invention”: • Need GEM cleaning procedure to recover these GEMs for test use…maybe success??

  5. Step-by-Step Cleaning Tests • Look at GEMs under low (magnifying visor) and high (microscope) magnification: • LOTS of dust (particularly top GEM). • Blow off with Bottle Gas: • Removes ~90% of dust • Not close to good enough. • Normal cleaning not good enough: • Wash with flow of deionized water. • Chase with ethanol. • Blow dry with bottle gas. • Little improvement…GEM looks bad. • UltraSonics!!

  6. UltraSonic Equipment from DCH • Pulled out equipment from storage. • UltraSonics in warmed deionized water bath: • 40 kHz, 70 kHz, 104 kHz, 170 kHz • Rough Cleaning  Fine cleaning. • Continual resistivity measurement • Tested one corner of one GEM dipped into UltraSonic bath: • US-off…swish around: no change dust remains. • US-on (40 kHz), “untouchable” dust gone in 30 sec. • Put whole GEM in tank: • 10 min at 40 kHz. • 1 min each at 70, 104, 170 kHz. • Quick look: • GEM looks pretty good • Used microscope on 1 strip…zero dust. • Resistors look really clean and pretty.

  7. Lessons Learned: • Scroll Pumps Leak when off! • Need electric gate valve. • Exhaust flapper (like on main chamber pump) • MAYBE (learn today) UltraSonic cleaning can successfully remove dust from a dirty GEM. • 1 strip from bad looking to looking perfect. • Good to know if there is a way. • Better to learn now than later. • Test one GEM for voltage holding before touching others • I’m encouraged • But keep your fingers crossed…

More Related